Search Documents

By Steven D. Scherer

The highest earthquake risk in the United States east of the Rockies is along the New Madrid Fault System, which extends for 193 km (120 miles) through the Central Mississippi Valley from northeastern Arkansas, through southwestern Missouri, western Tennessee and western Kentucky to southern Illinois. Historically, this fault has generated some of the most powerful earthquakes in U.S. history, notably three Magnitude 8 events in 1811. Apart from the West Coast, this region experiences more earthquakes than anywhere else in the United States, with more than 200 events recorded along the fault annually. These events are typically of much lower magnitude than those experienced in California. Most are too small to be felt. However, should a significant event occur, damage can be expected to be widespread because of the underlying geology. In recent years, earthquake preparedness and seismic upgrade of vulnerable structures has become a focus for a number of State Departments of Transportation, including those in Illinois and Missouri where there is a potential for future damage. This paper presents three case histories illustrating three different techniques used to retrofit interstate highway bridge foundations bearing on potentially liquefiable soils. Friction minipiles were installed at the approach span of the I-57 bridge crossing the Mississippi River near Cairo, Illinois to provide additional support to the pile caps in the event of liquefaction of the underlying sands during a seismic event. In St Louis, Missouri, rock-socketed minipiles were installed to increase the capacity of drilled shaft foundations supporting a section of Interstate 64. In Mounds, Illinois, compaction grouting was used to densify loose sand deposits beneath a pile-supported interstate bridge on I-57.

Jan 1, 2001

By Michael J. Garlich

Steel sheet piling has a long history of use in a variety of permanent and temporary structures. Current engineering practice uses numerous publications and standards for design guidance. U.S. design guidance is fragmented, with numerous inconsistencies between design guides. To improve current U.S. design practice, the North American Steel Sheet Piling Association has initiated a project to produce a design standard that will unify design procedures and provide specification guidance for engineers and users of steel sheet piling. The wide range of uses for sheet pile structures presents a challenge in developing such a standard. Load factors or allowable stresses acceptable for a temporary retaining wall in soil may reasonably vary from those for a river cofferdam or a dockwall located in sea water. However, it is still possible to provide consistent and rational guidance for such varying uses. The standard also can address sheet pile design aspects often neglected in U.S. publications, such as vertical load capacity and resistance to loads applied parallel to the sheeting.

Jan 1, 2008

By Brad W. Taylor

"During the past several months, I have introduced to civil and structural engineers an innovative solution for the integrity testing of concrete using the Thermal Integrity Profiler (TIP) Wire Cable System by Pile Dynamics. While in the process of “educating” highly-trained professionals about a technological breakthrough, I ended up being educated myself about their needs for quality control/quality assurance (QA/QC). With that in mind, I would like to focus on their two key areas of concern:• How complex is the TIP installation process?• How does the QA/QC engineereffectively analyze and report TIP test results?A few months ago, during a discussion with a senior QA engineer, he asked a question that stopped me in my tracks: “Why should we do foundation testing at all?” Turning it around, I asked, “Why wouldn’t QA/QC personnel want to know everything they could about their critical infrastructure foundation?” Honestly, I didn’t answer his question nor did I fully comprehend what he was trying to say. With his experience, the engineer understood that there has not been an integrity test or a combination of integrity tests that could deliver an inside the cage and outside the cage (cover) complete data set that would provide a definitive profile of the entire shaft. Crosshole sonic logging (CSL) becomes more effective the larger the diameter of the shaft becomes, with a maximum effectiveness between 70% and 80%, but does not provide any data of the integrity of the shaft beyond a straight line between CSL tubes. Gamma-gamma logging (GGL) provides qualitative information about the concrete surrounding the GGL tube and device, and it provides information about a small percentage of the drilled shaft concrete near its outside edge."

Jan 1, 2017

By Jesús E. Gómez

A total of 260 micropiles were installed as part of a retrofit effort for two existing bridges. The micropiles consisted of hollow core bars installed under limited headroom conditions. Of the total number of micropiles, 180 were installed in submerged sand and 80 were installed in stiff, silty clay. The micropiles were drilled using a lean cement grout which was re-circulated for de-sanding and re-use. Final grout was injected upon completion of drilling to the design tip elevation. The micropiles were subject to a rigorous quality control that included grout quality testing and proof-testing of each production micropile. This paper presents a description of the procedure for installation and quality control of the micropiles. The successful proof-testing of all the production micropiles showed that hollow core bar micropiles can be used effectively in granular and fine-grained soils. Hollow core bar micropiles offer particular advantages when installed in submerged sand formations with respect to other traditional micropile types. The results of the proof load tests are presented in a companion paper.

Jan 1, 2007

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By Mike Muchard

A design phase load test program was performed at the Broadway Viaduct bridge site to evaluate load carrying capacity and constructability of post grouted drilled shafts. The program included construction, instrumentation, post grouting and load testing of three drilled shafts. Two shafts included sleeve port and plate base grouting apparatus and were post grouted. The third shaft was un-grouted and served as a control shaft for comparison of the un-grouted end bearing. The shafts were 5 feet in diameter with the control shaft at 55 feet in length and post grouted shafts at 55 and 66 feet. SPT borings at the centerline of each test shaft defined geotechnical conditions at each shaft. Test shafts were instrumented with strain gages and concrete integrity was evaluated with crosshole sonic logging. Instrumentation and data acquisition was used during the post grouting operation to fully capture the shaft behavior. Finally, Statnamic load testing was performed on all three shafts to their ultimate capacity. The fine to coarse sandy soils in which the shafts were tipped in were well suited to improvement from post grouting. Grout pressures of 660 psi were achieved with 0.08 inch or less of upward shaft movement. Subsequent Statnamic load tests showed 183 to 192 percent greater end bearing in the post grouted shafts as compared to the un-grouted shaft. The overall result showed a potential savings of approximately 9 feet to 35 feet of drilled shaft length in addition to the increased quality assurance from post grouting.

Jan 1, 2009

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2013

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Lance Helwirg

New high and low double outfall bridge structures for a juvenile fish bypass system have been constructed on the Washington Shore approximately two miles downstream from the Bonneville Dam on the Columbia River. The high and low outfalls each extend approximately 400 feet into the river from the Washington shore and are designed to release juvenile salmon into the river at above-water discharge elevations for improved survival rates. The two outfall structures include post-tensioned concrete double box flume girders approximately 7 feet high by 13 feet wide, which will be submerged in river flows as high as 15 feet per second. Each of the 6 offshore foundation piers is composed of a single 10-foot diameter reinforced concrete drilled shaft with a permanent steel casing embedded into the river bottom approximately 100 feet. Challenging outfall design conditions included designing the entire structures to be submerged for long periods of time in 15-feet-per-second river water flow with a 60-foot cantilever at the end of each outfall, and with the superstructure 70 to 80 feet above the river bottom. Figures 1-1,1-2, and 1-3 show the high and low outfall structure overhead photos and elevation view.

Jan 1, 2001

By Clif Kettle

The paper will detail the design and execution of passive and active settlement control measures, the means adopted to overcome the various physical and operational constraints, and to meet specified allowable settlement criteria. The paper will highlight the close integration between the tunnelling and geotechnical contractors, designer, and Client, and demonstrate how particular practical difficulties were overcome by both the design and the construction methods.

Jan 1, 2008

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By Rob Jameson

Micropiles are ideally suited to seismic retrofit applications. Their high tensile and compressive capacity can sustain the large concentrated loads induced during seismic events. Micropiles can be drilled through and grouted into the wide variety of soil and rock materials encountered in seismically active zones, using equipment that operates effectively within existing structures. Micropiles have seen increased acceptance and are now widely specified for retrofit work in the San Francisco Bay Area. While installation equipment and the structural configuration of micropiles have been largely unchanged since the early 1990?s, market forces have pressured both engineers and contractors to continually optimize the cost and performance of seismic upgrades. Instead of the contractor simply developing stronger, stiffer and cheaper micropiles as isolated structural elements in response to a specification, focus has shifted to maximizing the efficiency of micropiles within the overall foundation system. The case history of seismic retrofit project in Berkeley, CA is presented to illustrate the collaboration between designers and drilling specialist which resulted in a structurally efficient and cost effective design. The seismic retrofit program for this 6-story concrete building was developed through careful consideration of the geotechnical and structural mechanisms of resistance, in combination with the deformation response of high capacity micropiles (2670 kN) under ultimate loading conditions. This case history describes the interactive project development emphasizing performance-based design and field testing to optimize the micropile foundations and the overall structural system.

Jan 1, 2008

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Brent Wilkins

The project team was tasked with the design and installation of a deep foundation system to support an expansion to a power generating station in Glenrock WY. Cast-in-place piles installed by a fixed mast drilling platform were assessed to be the most efficient foundation system for the subgrade conditions and range of design loads for the project. It was determined that conventional augered, cast-in-place piles could not be installed to the required pile toe elevations. Subsurface materials consisted of interbedded coarse- and fine-grained soils to about 23 ft to 30 ft depth below the ground surface, underlain by carbonaceous shale (claystone) with interbedded sandstone. The overburden materials varied from very soft to medium stiff and loose to dense. The claystone was typically foliated and very weak to weak whereas the sandstone was typically massive and very weak to weak. The site characterization consisted of a variety of field and laboratory programs including soil borings with Standard Penetration Tests, pressure-meter testing, and geophysical testing. A load test program was performed involving the compressive, lateral, and tensile testing of piles ranging from 14-in to 24-in diameter. Compression test piles were instrumented with vibrating wire strain gages. The paper includes a discussion of the regional and local geologic and geotechnical parameters, particularly the results of the various in situ and laboratory test programs. The selected foundation system is introduced. Load test results are then presented along with analysis and discussion of these results with regard to performance of the piles in the claystone.

Jan 1, 2009

By Mark S. Greenleaf, Alec D. Smith, Mary Vittoria-Bertrand, Heather B. Scranton, Jean Louis Z. Locsin

"Rhode Island’s new $163.7 million, 2,265 ft (690 m) long, four-lane Sakonnet River Bridge sits just south of the existing bridge in Portsmouth/Tiverton. The bridge, a critical transportation system link between Massachusetts and Rhode Island, has a steel I-girder main span and concrete New England Bulb Tee approach spans. The foundation work was done between October 2009 and July 2010, and the bridge was completed in February 2014.Foundation design and construction challenges make the project noteworthy. There were thick layers of silty glacial soils with bedrock as deep as 400 ft (122 m) below the waterline, coupled with high foundation capacity demands at the river piers in 50 ft (15 m) of water. The Sakonnet was one of the first major bridge projects in the country to incorporate AASHTO Load and Resistance Factor Design (LRFD) guidelines for foundation design and construction. Because of these and other challenges, the engineers conducted two design-phase load test programs on several foundation elements. These programs were successful and allowed the engineers to adjust the final foundation design prior to the start of construction. During construction, the contractors drove thirty 6 ft (1.8 m) diameter steel pipe piles, each with a novel recessed steel plate insert, to depths of 130 to 200 ft (40 to 61 m) at the three river piers. The insert provided increased resistance of the steel pipe piles and saved about $9 million. Also, 457 14x117 en bearing or friction H-section piles were driven to between 50 and 190 ft (15 to 58 m) at five land piers. All piles were driven relatively close to the existing bridge, which remained in service during construction, due to the project team’s precautionary use of instrumentation and the installation of a jacking system.Area GeologyThe Sakonnet River is up to 60 ft (18 m) deep along the bridge alignment and is underlain by a deep bedrock valley. The bedrock valley is buried by at least 350 ft (107 m) of soil, which includes a complex sequence of interbedded glacial soils (glacial till, glaciolacustrine deposits and glaciofluvial deposits), overlain by geologically recent estuarine deposits. The soils having the greatest impact on the foundation resistance are the glaciolacustrine (fine sandy silt or silt) and glaciofluvial (silty sand with gravel, cobbles, and occasional boulders less than about 2.5 ft [0.8 m] in size). The soil overburden decreases toward the east and west banks of the river, as the bedrock surface rises."

Jan 1, 2015

By Osama A. Safaqah

Driven plate anchors can be used to hold in place large bridge caissons during floating construction. Their small size and simple method of installation make them a very cost effective alternative to other direct-embedment, gravity, and drag anchors. The geotechnical design of plate anchors involves the anchor geometry, embedment, drivability, and proof testing. This paper describes the experience gained with plate anchors used during construction of the new Tacoma Narrows Bridge. For this project, the anchors had to be driven in dense to very dense sands, and had to resist large forces from 7-9 knot currents.

Jan 1, 2013

By Walter Kaeck

In a recent upgrade of their system, Amtrak converted a bascule type draw bridge over the Thames River to a vertical lift structure supported by the existing piers. During the bridge replacement, significant settlement occurred on one of the piers and movement continued thereafter. Construction was stopped as Amtrak became concerned as to how much the subsequent construction activities would cause the pier to further settle and tilt, not only impacting the operation of the existing bridge, but also jeopardizing the new lift span. Mueser Rutledge was engaged at this time to help understand and solve the problem. A remedial grouting program was developed to arrest the settlement. As a subcontractor to Cianbro Corporation, Pittsfield, ME, The Judy Company was hired to perform the remedial grouting work. Work platforms were constructed around the pier for support of the drilling equipment. A dual string drilling system was used to install sleeve pipes at depths of up to 185? below the water level. Ultrafine cement grout stabilized with additives was placed at 2.5 foot intervals through the depth of the sand and gravel stratum below the bottom of the pier. Logistics were difficult and the schedule was severely impacted by the remedial work, necessitating working six 12-hour shifts per week and working in the river through the winter months. After four months of drilling and grouting, movement of the pier stopped. At the conclusion of the remedial work, more than a million gallons of ultrafine cement grout were placed. Confirmation borings recovered completely solidified material with compressive strengths ranging from 500 to 1500 psi. The bridge replacement was then completed and is functioning. Continued monitoring through July 2009 shows negligible movement.

Jan 1, 2009

By Kenton W. Braun

Concourse B at the Anchorage, Alaska International Airport is currently being renovated while retaining the original building structure and foundations. Part of the renovation includes the installation of a new, permanent baggage tunnel system beneath the existing building. Installation of this cast in place concrete tunnel, beneath the existing structure, required installation of a steel retaining wall to support footing loads above the base of the excavation. Construction of this retaining wall presented challenging and unconventional design and construction methods. Detailed discussions of the design and construction techniques utilized for this project are outlined.

Jan 1, 2008

By K. Viking

It&apos;s well known that conventional impact hammers, usually are the method to use in order to drive precast prestressed concrete piles. However sometimes the vibratory technique might be considered as a suitable alternative due to favourable soil conditions. It is also well known that piles driven into granular soils can be installed more efficiently by the use of a vibratory driver compared with impact hammers. However, the use of the vibratory technique is seldom regarded as the first choice, since the technique is constrained by several uncertainties related to the pile capacity, and concrete piles to cope with tensile stresses. With the opportunities of having suitable subsurface conditions and a fair amount of piles to be installed, it was anticipated that the use of the vibratory method could result in a significant reduction of the installation costs. Part of the uncertainties of using a vibrator was intended to be eliminated by restriking the vibratory driven pile with an impact hammer and use a Pile Driving Analyzer? (PDA) to correlate recordings of soil resistance to driving with measured rate of penetration, and to evaluate the static capacity and load/settlement characteristics of the vibratory driven pile by conducting static load test. The conducted test study of using a vibrator to drive the precast prestressed test pile (14-in. square by 30-ft-long) did not turn out to the author&apos;s complete satisfaction. The present paper focuses mainly on a numerous practical engineering issues in relation to the use of the vibro-technique to drive precast prestressed concrete piles in granular soils. The obtained experiences of using a PDA to monitor vibro-driven piles, with its potential and limitations, is presented and discussed. Furthermore, a simple method of how to subjectively pre-estimate the soil resistance due to vibratory driving is presented and discussed. The reasons for the partly unsuccessful test study are discussed in great detail based on the obtained experiences. Suggestions of how to better approach a similar situation in the future are also provided in great detail

Jan 1, 2004

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner&apos;s engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel&apos;s observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile&apos;s geotechnical and structural design, and the contractor&apos;s pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005