Search Documents

By Marcelo Rebellato, Leonardo Silvestre, Zhang Yongqing, Felipe Bastos, Zhang Weiqiang

This work reviews the new version of GB1499.2-2018 Chinese national standard and specification, which governs the production of high-strength reinforcing hot rolled ribbed bars in China. In addition, it discusses the main concerns from Chinese rebar makers that might affect production and application of Nb-bearing rebars, like reheating temperature required to dissolve given niobium additions, the promotion of bainite microstructure and continuous yielding, as well as Nb strengthening effects. Through extensive investigation involving both thermomechanical laboratory simulations and industrial trial, the existing state and effects of Niobium along the reheating, rolling and cooling are illustrated. At the end, optimum processing conditions have been established to produce high strength rebars for the specified requirements. The adoption of new process conditions reflected in an amount of about 20.0 million tons of Nb-bearing rebar being produced in China in 2018 with required tensile properties and microstructure, and helped rebar makers to reduce production costs considerably. Based on production data, Niobium demonstrated positive strengthening effect for high strength rebars, in particular for small diameter rebars with earthquake resistant performance. What is more, the results of the research enrich the knowledge of the application of Niobium in steels when TMCP rolling is not used.

Oct 1, 2019

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

By Laurent Dorel

Surface quality monitoring is primarily implemented in the last steps of steel manufacturing before shipment to the end user. However, an increasing trend for also addressing this topic in the upstream stages, such as hot rolling plant, is tackled by Primetals Technologies to give steel producers the key to a global optimized yield management, and efficient “lessons learned” processes. After the last developments of SIAS Next Gen platform, including High Resolution and Near Infra-Red, some site results will be exposed on the very specific high constraints lines such as ESP Endless Strip Production and Plate Mills, and highlights the related most interesting aspects for our customers.

Aug 17, 2017

By Francisco Morganti

The market requirements which strip processing lines have to deal with have altered significantly within the last decades. Particularly, the production has to be economical and ecological efficient and processing lines have to cover a broad product portfolio. Already existing plants either directly or indirectly are competing with new plants, which are equipped with the latest technologies. The “Special Strip Processing Equipment” is designed to be integrated easily and within small downtime phases in existing lines. All single machines can be delivered in short time “ready-to-perform” with a tested and proved automation system. Thus, the competitiveness of existing lines can be increased immediately with less effort. To find out which machines can be reasonably implemented SMS group offers an “Efficiency Check”. A special proceeding is used by experts to find out quickly which machines will have the largest effect on the efficiency of the line while demanding at the same time the smallest expense.

Aug 17, 2017

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017

By Eddy Dierckx

Modernization of flat rolling plants is essential to sustainably fulfill increasing market demands and to improve competitiveness. Intelligent modernizations ensure getting maximum prime yield of existing mills, even if they have gone through half a century of operation. Existing mills were designed based on former production, consumption and quality targets. Ever increasing requirements such as increase of productivity, change of product mix (e.g. new steel grades), reduction of energy consumption and improvement of product quality lead to the necessity to adapt the existing equipment to the new target. SMS group provides, besides the reliable equipment and automation solutions to successful upgrades of existing mills, also a systematic approach to develop technical and economical solutions together with our customers (conceptual engineering). This paper describes the SMS group approach to modernizations / upgrades, introduces powerful performance modules and provides a number of successful examples that have been implemented recently.

Aug 17, 2017

By Saul Garcia Hernandez

The research work objective is to study a new ladle shroud internal design to reduce the slag emulsification in the tundish during ladle transient periods. A 3D mathematical model of the tundish was created to solve the fundamental equations, a turbulence model, and a multiphase model. The results show that using a conventional ladle shroud, the fluid is delivered with an excessive amount of kinetic energy being dissipated inside the tundish bath, generating strong mixing flow patterns and entrapping a massive amount of slag. In the other hand, the proposed ladle shroud dissipates the kinetic energy before the fluid enters the tundish promoting less intense mixing patterns; thus, the amount of slag emulsification is reduced significantly. Consequently, if the internal design of the ladle shroud is able to dissipate the kinetic energy before the fluid enters the tundish, it shall be possible to reduce considerable the slag emulsification and the slag opening area.

Aug 17, 2017

By Theodore James Kurela

Analysis of adverse technical issues has traditionally relied on a snapshot of the state of the operation complemented with both the melt shop’s archived data and eyewitness accounts of adverse events. The GrafTech ArchiTech System is helping EAF shops solve problems faster by combining continuous analysis of information with statistically based alerts of process deviations. After one year of system implementation, a number of cases have been detected and communicated to melt shops worldwide. The objective of this paper is to examine a few of these cases; the early detection, statistical analysis, deviation reporting and the resulting countermeasures implemented.

Aug 17, 2017

By Jorge Madias

Los hornos eléctricos de arco han sido motivo de una aplicación dinámica de nuevas tecnologías en lo que va de este siglo. La preparación de la chatarra y el uso de materiales de carga alternativos han dado lugar a la concepción de nuevos equipamientos y experiencias en todo el mundo. Surgen nuevos conceptos para el precalentamiento de la chatarra, superando las limitaciones de mantenimiento y ambientales de los conceptos iniciales y mejorando su performance energética. El aporte de energía química para la fusión supera sus límites año a año, requiriendo el desarrollo de equipamiento capaz de una acción rápida y precisa con grandes caudales de gases y sólidos inyectados. Existen nuevas herramientas para eliminar los riesgos de seguridad en la plataforma del horno, haciendo uso de sistemas de enfriamiento más seguros y duraderos, robots, automación de la operación del agujero de colado, y puertas de escoria controladas desde el púlpito.

Aug 17, 2017

By Ronaldo Câmara Cozza

Iron aluminide alloy; Ball-cratering wear testing; Rolling abrasion; Wear volume; Coefficient of friction

Jul 31, 2018

By Andrea Taurino

Innovation means implementing a new product or a product that has undergone significant improvement over time, in terms of method, form and performance. Innovation encompasses all the scientific, technological, organizational, financial and commercial steps that need to be taken to put it into operation. Innovation combined with research and development makes it possible to perfect the product with consistency over time. Taking inspiration from the bases developed by the Austrian economist Joseph A. Schumpeter back in 1911, Danieli came up with the concept of “Innovaction” – a combination of Innovation and Action, to refer to the development and advancement of various products for the steelmaking industry, including the loop laying head for wire rod.

Aug 17, 2017

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By Dusan Ilic

Conveyor system wear of belts and transfers attribute to a significant proportion of the maintenance costs and lost productive hours when handling hard abrasive ores at high unit rates typical of the iron ore industry. The recent growth phase has seen a rapid increase in mine and export capacity, with many new and upgraded plants operating at high throughput and utilisation. Subsequently, the industry has progressed to an optimisation phase, seeking to maximise production capacity and reduce maintenance costs with minimal capital spend. To support this, a programme of modifying designs was executed to improve conveyor transfer chute and belt life, which identified a need to challenge the industry practice for specification of designs to improve the functionality of the installed equipment. While acknowledging the importance of selecting the highest wear resistant materials for the intended application, this paper investigates design criteria related to decreasing conveyor transfer and belt wear. Of focus is a shift in the manner in which designs are specified, from specifications primarily governing geometrical constraints, to those meeting technical and functional requirements aimed at producing optimum geometry for a given set of material handling parameters. An assessment of transfer design criteria is presented.

Aug 17, 2017

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By Luke A. Balzan

Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such realtime information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing a case study of their use at an Australian site, and a description of the potential benefits of a range of analysis equipment.

Aug 17, 2017

By Qingwen Dai

The Marangoni effect is an important phenomenon where a surface tension gradient drives liquid towards high surface tension regions. Temperature gradient, evaporation, disparity of viscosity, and surface roughness and topography are all significant factors that can affect this thermo-capillary migration. The purpose of this study was to investigate the influence of micro-groove patterns on the migration of paraffin oil, and obtain a well-designed texture of micro-grooves to prevent the thermo-capillary migration. Patterns of micro-grooves with differing orientations and geometric parameters were fabricated on the surface of SUS 316 stainless steel substrates. Experiments on the migration behavior with different viscosities of paraffin oils were carried out various temperature gradients. The experimental phenomena indicated that the surface with the micro-grooves perpendicular or parallel to the temperature gradient have a strong impact on the migration performance of paraffin oil. Micro-grooves perpendicular to the temperature gradient exhibited extraordinary slower migration velocity than that of the parallel one. Width and depth of micro-grooves had an obvious influence on the behavior of temperature-driven migration and detail discussions on the effects of these geometric parameters were carried out.

Jul 31, 2018

By Shibu John

Rising energy demand and steadily decreasing quality of raw materials due to the global resource depletion are great challenges to the steel production today. The FINEX® Process has been developed jointly by POSCO, Korea and PRIMETALS Technologies Austria, to provide the iron making sector with the capability to lower hot metal production costs, environmental pollutions and to increase the flexibility in terms of operation and the choice of raw materials. FINEX® is a new technology combining a gas-based reduction in a series of fluidized bed reactors and a reduction smelting in a melter gasifier. Commenced in April 2007, the first 1.5Mtpa commercial plant has demonstrated the competiveness as an alternative iron making route. Another 2.0 Mtpa, third generation FINEX® (3G) plant was recently installed at POSCO, Pohang Works and has been operating satisfactorily since its blow-in in January 2014. Based on the well-proven plant concept, new process features, the highly competitive production costs and environmental advantages, the FINEX® Process can be considered as a competitive alternative to the conventional blast furnace iron making route.

Aug 17, 2017

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017

By Daniel Eduardo Parodi

Para acompañar el plan de aumento de producción de slabs de Siderar, fue necesario proyectar una nueva unidad separadora de aire para incrementar la generación de oxígeno, nitrógeno y argón. La premisa que direccionó este proyecto fue la integración y sinergia de la nueva unidad con el sistema de la Central Termoeléctrica y Altos Hornos, con el objetivo de salvar condicionamientos, obtener beneficios energéticos y aumentar la confiabilidad operativa. Como resultados de esta línea de trabajo se espera: Optimizar el aprovechamiento de gases de proceso, mejorando así el balance energético y la ecuación económica en la producción de los gases industriales; Mejorar el aspecto ambiental disminuyendo el quemado de gases en antorcha, reduciendo el consumo de combustibles fósiles y la compra de energía eléctrica; y aumentar la confiabilidad en el suministro de gases y del sistema de aire soplado a Altos Hornos.

Sep 25, 2017

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017