Search Documents

By M. R. Geer

The Bureau of Mines surveyed the solid wastes that have accumulated from coal mining in Washington, Oregon, and Montana. Location, amount, character, and condition were determined, and both economic and environmental factors were considered. Areas covered by waste comprise 800 acres in Washington, 5 acres in Oregon, and 1,200 acres in Montana. In a few cases waste is being utilized, particularly cinder from burned refuse dumps, as fill in road construction and as a ceramic raw material. It is estimated that wastes deriving from coal mined for electric power generation by 1974 may amount to 3 million tons of washery refuse, 2.7 million tons of fly ash, and 1,000 acres of spoil banks.

Jan 1, 1969

By Wilbert J. Huff

The work of the Explosives Division, Bureau of Mines, United States Department of the Interior, for the fiscal year ended June 30, 1939, is described in the following pages. This paper is the fourth of a series of annual reports covering the activities of the division since July l, 1936.

Jan 1, 1940

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By Sidney Katell

This report is the fourth in the series, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants. The initial work, Bureau of Mines In- formation Circular 7516, was published in October 1949 in conjunction with the synthetic liquid fuels program authorized by Public Law 290, 78th Congress. It included references to and abstracts of publications appearing from 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. A supplemental bibliography, Bureau of Mines Information Circular 7705, was published in January 1955 to cover the period September 1948 through June 1952; and Supplement 2, Information Circular 7751, published in September 1956, covered the period June 1952 through June 1954. The present supplement covers the period July 1954 through December 1956.21 The information in this paper was obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Reports of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Engineering Costs Quarterly (Cost Engineering).

Jan 1, 1958

By Joseph Sabatini

This report, covering the period January through December 1975, contains abstracts of articles concerning all phases of cost engineering and economics for chemicals processing, raining, and other mineral industries. The abstracts are collected from the following sources: 1. Chemical Engineering 2. Chemical Engineering Progress 3. Chemtech 4. Coal Arse 5. Coal Mining and Processing 6. Combustion 7. Drilling 8. Electrical World 9. Engineering and Mining Journal

Jan 1, 1976

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By John J. Mulligan

The Bureau of Mines investigated coal deposits at Mount Gran (latitude 76°59' S, longitude 161°07' E), Victoria Land, Antarctica, during the austral summer of 1959-60 as part of the continuing U.S. Antarctic Research Program, which is under the auspices of the National Science Foundation. The coals and associated rocks were measured, sampled, and analyzed. Five coalbeds, ranging in thickness from over 10 feet to scattered fragments of coaly material in sandstone, occur in a sandstone-coal series overlying a series of crossbedded red-buff sandstones. Both series are part of the Beacon group of sediments, and both show some evidence of pressure metamorphism. The sandstones are poorly cemented and are composed dominantly of rounded and often frosted quartz grains. The sediments have been broken and uplifted by a series of massive diabase sills. The broken nature of the sediments precluded an estimate of the amount of coal present. The Mount Gran coals are highly attrital banded anthracites and semianthracites that have most commonly a moderately dull luster but do include bright bands. Coal in contact with or near diabase intrusives is partly graphitic but shows no evidence of coking. Apparently the coal was beyond coking rank before emplacement of the adjacent intrusives. Fragments of the plant Glossopteris indica found with the coal suggest Permian age but do not prove it. The coals appear to be derived from plant remains that collected in shallow basins; individual coalbeds would tend to be lenticular bodies that formed in different places as the dominantly sandy sediments were deposited. The wide distribution of coal indicates that coal-forming conditions prevailed over much of the continent; the great thickness of Beacon sediments indicates that similar conditions may have persisted through a long period of geologic time. Generally similar coal deposits may occupy widely separated stratigraphic positions.

Jan 1, 1963

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By James C. Barker

Yttrium and rare-earth element. pegmatite dikes are associated with a peralkaline granitic and nephelene syenite complex near Dora Bay on southern Prince of Wales Island. Mineralized dikes were mapped and sampled during USBM investigations in 1987 and 1988. Coarse-grained pegmatite dikes, which emanated as late-stage magmatic fluids from the intrusion, further evolved into vein-dikes and ultimately silica-rich veins. The dikes can be traced up to two miles along a north-south zone. Lithophile elements exhibit a pronounced zonation in vein-dikes and veins that are distal to the Dora Bay complex with increasing values correlating with increasing distance from the complex. The pattern of mineralization suggests very late stage magmatic fluids containing the incompatable lithophile elements were injected into a preexisting north-south fracture zone. REE mineralogy exhibit fine-grained intergrowths of principally thalenite and bastnaesite with lessor monazite and eudialyte. Euxenite contains most of the columbium values and zircon is commonly associated with the dikes. Estimates of inferred and hypothetical resource tonnage range from 1.7 X 1C6 to 8.5 X 106 st for two deposits. Contained RED (including yttrium) averages 0.5 pct and ranges up to 2.0 pct. Deposits are of polymineralic composition and about half of this resource comprises the heavy yttrium subgroup.

Jan 1, 2011

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By H. C. Miller

For nearly a score of years the American petroleum industry has faced the problem of maintaining its economic structure while oil -producing potentialities greatly exceeded the increasing market demand for oil and its products . However , the combination of maximum civilian demand with rising defense requirements caused an all - time peak in crudeoil production in the latter half of 1941 , with a daily production (as estimated by the Bureau of Mines ) of 4,139,000 barrels in December - an increase of 16 percent over the daily production of 3,573,000 barrels in December 1940. In the event of a long war , a continuing , steady, and adequate supply of petroleum and its products for military and required civilian needs is essential, and the efficiency of recovery of oil from natural underground reservoirs will have to be maximum. Whereas it may not be possible to increase production in some fields , the output from others may have to be drawn at a much faster rate than formerly . More than 10 years ' experience in operating oil fields under proration control has demonstrated to petroleum engineers that some of the efficiency of recovery of oil from reservoir sands and rocks is sacrificed if the oil and gas are withdrawn at too . rapid a rate . As petroleum is an irreplaceable natural resource for which suitable substitutes probably will not be available in desired quantities for many years , any producing method that jeopardizes the quantity of oil that may be recovered from underground reservoirs must be considered at this time of declared war against aggressor nations as conflicting with the best interests of national defense . At best, the efficient recovery of oil is a complex problem . It involves not only a knowledge and application of the fundamentals of fluid flow through porous mediums, but the sources of energy responsible for the movement of oil and gas through reservoir sands and porous rocks to wells must be known to determine the best practices for extracting these hydrocarbons . Reservoir energy is of two kinds - (1 ) water under hydrostatic head underlying the oil in the extraneous parts of the reservoir system and ( 2 ) natural gas under pressure as "free " gas in the reservoir or in solution in the oil . Inasmuch as the efficiency of oil recovery depends largely on the manner in which reservoir energy is used to move oil through reservoir sands and porous rocks to wells , optimum practices for withdrawing the oil cannot be determined until it has been established that the oil in the reservoirs is being forced to wells by an internal gas expansion, by a natural water drive , or by a combination of gas expansion and water drive . There is a fundamental difference in the performance characteristics of gas - expansion and water - drive reservoirs . In a strictly gas - expansion reservoir the energy available to move oil and gas through the porous formations to wells results solely from gas pressure , which is maximum when the reservoir is tapped by the first well . Pressures decline as oil and gas are withdrawn ; consequently, the energy available for moving oil and gas through the oil - bearing formations to wells decreases with production . Curtailing the oil - production rate or shutting in gas - expansion reservoirs entirely will not act to replenish energy previously used in the production of oil and gas ; in their operation , therefore , it is especially important not to waste reservoir energy - the production of oil with high gas : oil ratios will be reflected in lower ultimate recoveries of oil .

Apr 1, 1942

By E. P. Youngman

Titanium ranks as one of the more abundant elements, is widely distributed, and occurs in concentrated form in numerous deposits. This substance was discoveres 140 years ago; but despite the efforts of metallurgists and chemists to find a place for it in industry, only within the last 10 or 15 years has the increased use of titanium pigments provided any extensive outlet for titanium ores. Even to-day titanium is confined to a few highly specialized industrial applications. The metal itself is now quoted regularly in trade journale, but scarcely yet can it be said that the production or use of the metal. has progressed very far beyond the laboratory stage. Ferroalloys containing the element were largely used for a time, especially in connection with the manufacture of Bessemer steel rails; but as American rail- ways adopted open-hearth rails in preference to Bessemer rails, the demand for the alloys in the rail manufacture gradually dwindled into insignificance. New outlets for ferrotitanium have been found in the steel industry; and the production of titanium alloys, both in the United States and in Europe, has increased in recent years. By far the largest use of titanium at the present time, however, is in pigments. The manufacture of titanium white began in Norway, but at present the United States is the leading producer. One of the two companies now operating in the United States is also the leading factor in European production. Although titanium occurs, in many minerals, the principal commercial sources are rutile (the natural oxide, Ti02) and ilmenite (iron-titanium oxide, FeO. TiO2). The latter is a coal-black mineral, but it is the one used in the manufacture of the titanium white of commerce, as well as in the manufacture of ferroalloys and arc-lamp electrodes. Rutile, the natural oxide, is not pure white and, being less common in nature, costs more; it is, therefore, reserved for use in the manufacture of titanium chemicals employed in relatively small amounts in dye works and bleacheries and for sundry minor purposes. This paper summarizes the titanium industry, with special reference to its economic aspects. It is offered as a survey of current trade literature and as a digest of material in the files of the bureau and is presented in response to numerous inquiries from prospective producers as to ways and means of exploiting deposits. (At present, much of the ilmenite consumed in this country comes from overseas, principally from British India..). A forthcoming circular, devoted to deposits of titanium-bearing ores, deals with foreign and domestic sources of supply.

Oct 1, 1930

By Louis C. Brichta

"The O'Jack Mining Co.'s zinc and lead deposits in Jasper County, Missouri, have been worked intermittently since the early nineties; production from these deposits was greatest during World War I and II - 4,668 tons of zinc and lead concentrates. The deposits are in a sink-hole structure in which intense deformation has taken place and in areas of disturbance in the sheet-ground horizon.While high-grade ore was being mined, the operators sank seven churn-drill holes for the purpose of extending reserves. They then asked the Bureau of Mines to explore the deposit with the object of developing a reserve of lower-grade ore that could be mined by open-pit methods. Twenty-two holes were sunk. The methods of drilling and sampling and the logs of the holes, as of those drilled by the operators, are given later in this report.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mined has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts development by each exploratory project as soon as practicable after its conclusion. Preliminary examination, conduct of exploratory work, and preparation of final reports are functions of the Mining Branch, Lowell B. Moon, chief, under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By C. M. Harrer

The location, features, qualities, and extent of iron occurrences and the associated resources--limestone and dolomite, bentonite, coal-lignite, petroleum and natural gas, power, and water--are evaluated. The results of pioneer beneficiation tests on South Dakota taconite are discussed. In addition, pertinent features of taconite development, cost factors, the Western and Central United States trade area and markets are reported. The State's production of iron ores until 1963 has been small and for purposes other than the manufacture of iron. This investigation disclosed the probability of large resources of taconite in Pennington and Lawrence Counties. The average iron content is 29 percent, and a 65-percent or better iron concentrate might be produced. Ample resources are available for mining and processing taconite. An investment of at least $26 million would be required for a plant capable of turning out 1 million tons of agglomerated iron concentrate per year. The feasibility of such an enterprise is indicated, but intensive investigation and research must be completed to justify such an investment,

Jan 1, 1966

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system, or systems, thus disclosed. Of the several systems initially investigated and evaluated, four showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD's. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

The goal of the Bureau of Mines diesel engine research program is to reduce exhaust emissions and minimize the risk of fires and explosions caused by the use of diesel- powered equipment in underground mines. This program has led to a fundamental understanding of the problems and to solutions that allow diesel equipment to be used safely and effectively. This volume contains reports of the presentations made at the Bureau Technology Transfer Seminar on Diesels in Underground &fines given in Louisville, KY, and Denver, CO, on April 21 and April 23, 1987. It also contains three reports of related research, not presented at the seminar, which highlight the significant achievements of a joint US.-Canadian research program on diesel emission control technology for underground mines. Topics covered in this volume include discussions of industrial hygiene problems associated with the use of diesels, accident statistics, fire and explosion control systems, measurement of diesel pollutants, emission control techniques including engine maintenance, fuel additives, diesel particulate filters, and ventilation of diesel sections. An alternative to diesel power, the hydrogen-powered mine vehicle, is also described.

Jan 1, 1987

By W. F. RITTMAN, E. W. Dean

This report presents the results of an investigation conducted by the Bureau of Mines for the purpose of assisting in the establishment of a satisfactory standard method for the analytical distillation of petroleum, a problem of great importance to the petroleum industry. Experiments were performed for the purpose of studying the charac- teristics of methods typical of those in use; comparative studies were made of the efficiencies of the principal types of fractionation ap- paratus available to the petroleum chemist; and the characteristics of a type of apparatus that the results of the experiments seemed to indicate was best adapted to the purpose were investigated in detail. Also, some experiments were made to determine the effect of cracking as a factor in the analytical distillation of petroleum in still heads.

Jan 1, 1916

By Perry D. Teitelbaum

In two earlier studies the Federal Bureau of Mines undertook to explore comprehensively the dimensions of the Nation's energy balance. The first of these studies, published in 1950 as Bureau of Mines Information Circular 7582, by Harold J, Barnett, was primarily concerned with projections of future domestic energy requirements and supplies, because these related to projected growth in major fuel-consuming sectors of the economy, changing rates of energy-use efficiency, and interfuel substitution patterns. But, to provide the essential background for these projections, it was first necessary to assemble and examine in some detail the quantitative information on the size and shape of the current United States fuel economy. Among other things, Barnett's path-breaking study indicated the need to consider energy as an entity, particularly for public and private policy makers, industry and commodity analysts, economists, and others concerned with long range questions of domestic and international energy supply and demand. The study also spotlighted a gap in the fabric of current economic intelligence; no comprehensive collation and reconcilation in any single report of available published statistical information covering the origin -a disposition of all energy materials existed. In response to this latter need, the Bureau of Mines prepared the second of the two studies referred t3 above. This was published in 1951 as Report of Investigations 4805, by W, H, Lyon and D, S. Colby, and it consisted of statistical information on the production and use of each of the various fuels and electric energy in the United States for 1929, 1939, and 1947; all were presented in tabular form and on a uniform basis. The three years selected were chosen largely on the basis of data availability.

Jan 1, 1961

The complex organic chemicals in coal differ from those in petroleum mainly by the ratio of carbon atoms to hydrogen atoms; this ratio is about 2 for coal and 1 for petroleum. By changing the ratio, coal can be converted into compounds similar to those found in petroleum. In. very simplified form, omitting here the special conditions required, the paths by which this can be done are: [ ] Part or all of the coal is first gasified by reaction with steam and oxygen, either in a gasifier or while the coal is still in place underground. The resulting gas is mainly hydrogen and carbon monoxide, with impurities that .must be removed before further processing by one of the following routes.

Jan 1, 1959