Search Documents

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By P. Sharma

Longwall panels facing wind blasts have been investigated at both Newstan and Moonee Collieries in the Newcastle Coalfield under the Wind Blast Project of the School of Mining Engineering, The University of New South Wales. The fluid mechanics involved in the compression and expulsion of air during wind blasts have been defined and the overpressure and air velocity time histories utilized to determine the wind blast parameters and define the relationship between them. The characteristics of wind blasts pressure pulses in mine roadways show some similarity with transient phenomenon like air blasts from explosives and shock waves from the failure of pressurized vessels. The peak wind velocities in roadways, however, exhibit marked deviations from theoretical predictions based on compressible fluid flow and Rankine-Hugoniot relationships applied to goaf air displacement and panel geometry. Peak overpressures and wind velocities have shown a positive correlation with the areas of goaf falls, with the values peaking off for larger areas. The field investigations have helped the mine management in risk assessment and in evaluating the success of induced caving by hydrofracturing to mitigate the hazard.

Jan 1, 2004

By T. Lindstad, J. Kaczorowski

The Boudouard reactivity of single cokes produced from selected bituminous coals and commercial cokes has been investigated in a thermo gravimetric furnace. The effect of potassium as a catalyst for this reaction was studied, as it is known to accumulate in ferromanganese furnaces. A gaseous impregnation technique using K2CO3 as the potassium source was applied to impregnate the coke samples. The reactivity experiments were designed to simulate conditions occurring in an industrial furnace, as used for production of Mn-alloys. The coke particle size varied from 3.35 to 6.63 mm, while the temperature was maintained between 800- 1100oC with a gas composition from 50 to 75% CO2 in a CO/CO2 mixture. To determine the catalytic effect of potassium, the concentration varied from a fraction of a percent up to 15%wt. The results show that single chars vary significantly in reactivity, depending on the properties of the parent coal, while commercial cokes exhibit similar reaction rates. Temperature and partial pressure of CO2 have the strongest influence on the reactivity, while the influence of gas flow rate and coke particle size were found to be negligible. The catalytic studies revealed that the relative reactivity of non-impregnated samples are preserved after the impregnation, so the least reactive coke is still the least reactive after the impregnation for the whole range of potassium loads. Also, it has been confirmed that the Boudouard reactivity reaches a plateau at potassium concentration of 4%wt.

Jan 1, 2007

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By C. Balci

Specific energy is defined as the amount of work required to break a unit volume of rock and is used to predict the performance of mechanical miners. It is obtained from full-scale rock cutting experiments, which require large block samples, experienced personnel and expensive equipment found in only a few research centres in the world. Estimation of the optimum specific energy, at which a given geological formation is excavated at optimum cutting geometry in the most energy efficient manner, from mechanical rock properties to predict the performance/efficiency of roadheaders is the basic aim of this study. The mechanical rock property tests require only core samples, which are easier to obtain and to test. In this context, full-scale rock cutting tests are performed on 23 different rock, mineral and ore samples including sandstone, claystone, tuffite, chromite, trona and copper collected from some operating mines in Turkey. The optimum specific energy values are obtained for each sample. Physical and mechanical property tests are performed on the core samples obtained from the same samples to determine uniaxial compressive strength, indirect (Brazilian) tensile strength, static and dynamic elasticity moduli, Schmidt hammer rebound values, density, and Cerchar abrasivity index. The relationships between the optimum specific energy and the mechanical rock properties are analysed using statistical methods. The results indicate strong relationships between the optimum specific energy and the mechanical rock properties. The strongest relationships are found by using uniaxial compressive strength and tensile strength. The performance models developed in this study are in good agreement with the empirical models previously developed for roadheaders and can be used reliably for prediction purposes. Keywords: Mechanical excavation, roadheader, performance prediction, rock cutting, optimum specific energy, mechanical properties of rocks.

Jan 1, 2004

In ilmenite smelting, the FeO content of the feed material (nominally FeO.TiO2) is decreased by reduction with carbon. In a parallel reaction, a significant amount of the TiO2 is reduced toTi2O3. One of the striking features of these reactions is a consistent relationship between the extents of FeO and TiO2 reduction; this relationship is independent of furnace size. It was recently proposed that this relationship follows from the solidification behaviour of the slag, where the final slag composition corresponds to the minimum melting point (?eutectic groove?) in the FeO-TiO2-Ti2O3 phase system; the hypothesis is that solidification equilibrium with the freeze lining stabilizes the slag composition. If this is the case, the system of slag and freeze lining must be capable of correcting two types of disturbances: thermal and compositional. Thermal disturbances result from incorrect power input, for the feed rates of ilmenite and reductant. For example, excessive power input will tend to overheat the slag, causing the freeze lining to melt partially, establishing a new steady-state heat loss from the furnace. Compositional disturbances result from an incorrect reductant input for the given power and ilmenite input. In this work, the dynamic response of the slag and freeze lining to different inputs (flow rates of ilmenite and reductant, and power input) is modelled. The model is based on solidification equilibria, and quantified heat loss through the freeze lining. The conclusion is that the solidification equilibrium cannot constrain the composition to the eutectic groove for typical operating conditions. Keywords: ilmenite smelting, freeze lining, solidification, high-titanium slag

Jan 1, 2004

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By A. L. Edwards

A two-year study focused on current noise exposure levels in the South African mining industry, aimed at helping the Mine Health and Safety Council of South Africa meet its milestones for eliminating noise-induced hearing loss (NIHL). Methods A multi-task methodology was adapted from international baseline studies to determine the exposure to noise in both large-scale and small- to medium-scale mines. Results On average, 66.7 per cent of the employees sampled in year 1 and 78.4 per cent in year 2 were exposed to noise levels of above the 85 dB A legislated occupational exposure level. Conclusions Information obtained through the study could be developed into a national personal noise exposure database, including audiometric results, equipment noise emission levels and initiatives for noise engineering control by mines and equipment manufacturers to facilitate targets of eliminating NIHL. Keywords Noise exposure levels, mining industry, noise-induced hearing loss

Jan 1, 2011

By N. Sahay

Improvement in work place environment by conventional methods viz., installation of higher capacity fan, fans in parallel operation or booster fan is a risky proposition in many coal mines in India because of difficult geo-mining condition such as shallow depth, multi seam workings having thin parting and inter connected goaves one above the other. The situation is further worsened if the mines have fire affected sealed off area connected to different ventilation circuits. On many occasions circulation of more air quantity by increasing fan pressure have resulted in initiation of spontaneous heating. To address these problems, authors have made some improvement in conventional Dynamic Balancing of Pressure Technique and worked out few ventilation schemes which are aimed for neutralization of pressure differential across sealed off area at the same time having improvement in ventilation in the mine. The excess pressure differential across sealed off area is mainly caused by introduction of higher capacity fan. Similar situation prevailed in one of the mines of Jharia Coalfield, India. The problem was solved by application of the above technique. In this paper, brief description of the technique, the problem in the mine, results of investigation, computer simulation studies of various schemes and methodology adopted for implementation of the technique in the mine have been discussed in some detail. Keywords: Dynamic Balancing of Pressure Technique, Spontaneous heating, Work place environment.

Jan 1, 2003

By A. S. Macfarlane

The South African Institute of Mining and Metallurgy was approached by the Australian Institute of Mining and Metallurgy to present a paper on the current practice in terms of the valuation of mineral projects and properties, given the development of a Code for the Valuation of Mineral Properties, developed in Australia (the VALMIN Code), and a similar Code in Canada (the CIMVal Code).This paper is the result of research and investigation into the matter, in terms of the reporting of Mineral Resources and Reserves, financial reporting practice, the Listing Rules of the Johannesburg Securities Exchange, and various practices in valuation. The paper establishes that a strong linkage has already been established between the SAMREC Code for the reporting of Mineral Resources and Reserves and the Listing Rules, and that, for completeness, a Code for Valuation needs to be developed. This Code will be similar to its international counterparts, with the necessary inclusions which are relevant to South Africa, and will provide guidelines and definitions on matters such as transparency, materiality and competency in valuation. It proposes that a multi-stakeholder steering committee be established under the auspices of the SAIMM, to deliberate and design a process for establishing such a Code.

Jan 1, 2002

By N. J. Castilla, R. Giglio

"Circulating fluidized-bed (CFB) combustion technology has been around for over 40 years, but over the last 6 years it has been commercially demonstrated at the 500 MWe scale at the Lagisza plant located in Bedzin, Poland. The CFB at the Lagisza plant has unique first-of-a-kind design features, such as vertical-tube supercritical steam technology and a lowtemperature flue-gas heat extraction that allows the plant to achieve high plant efficiencies of over 43% (net lower heating value). Another unusual feature for a coal power plant is that this plant meets all its atmospheric emission permit levels without any post-combustion de-NOx or de-SOx equipment such as selective catalytic reduction (SCR) or flue-gas desulphurization (FGD).CFB clean coal power technology is entering the utility power sector just in time to help deal with declining quality in internationally traded coals and to promote the large-scale use of economic, low-quality domestic fuels. Owing to the very attractive price discounts, growing supplies of low-quality Indonesian coals are outpacing the supply of high-quality Australian, Russian, and US coals. In Germany and Turkey, the use of domestic lignites for power production provides a secure and economic energy solution while creating domestic jobs.Conventional pulverized coal (PC) boilers will have trouble accepting these off-specification coals because of their narrow fuel specifications; they typically call for heating values above 5500 kcal/kg. This limitation is not an issue for CFB technology because of its ability to burn the worst and best of coals with heating values ranging from 3900 to 8000 kcal/kg.This paper provides an outlook for future coal supply, quality, and price, as well as a review of the technical and economic benefits of CFB technology firing low-quality fuels for utility power generation."

Jan 1, 2015

By R. G. B. Pickering

Resue mining was practiced extensively in the East Rand in the first half of this century. The obvious benefits were that a higher grade of ore was trammed to the surface. The disadvantages were slow rates of face advance and an extremely labour-intensive method of mining. A collaborative effort by personnel from Avgold?s Target Gold Mine and Sandvik Tamrock has resulted in the design of a method of resue mining which can be totally mechanized. The purpose of this paper is to describe the methodology used and the proposed new mechanized resue mining method.

Jan 1, 2000

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

By L. Bbosa

Paper written on project work carried out in partial fulfilment of BSc (Hons) (Eng) (Mechanical) degree Discrete element methods (DEM) are being used to provide detailed impact histories of the particles in comminution devices, such as mills. To match this immense detail of information, far more informative breakage tests than those that are generally conducted are now required. The split Hopkinson pressure bar apparatus is used in this study, as it allows the calculation of breakage forces and absorbed energies. The geometry of rock particles has been identified as significant, so this project undertook to identify the influence of shape on the breakage pattern of blue stone. Comparisons are then made between the breakage pattern of angular rocks and rounded, milled rocks for single impact fracture and consecutive impact loading at low energy. Results of this experiment indicate that although breakage for both geometries occurs over a similar energy range, rounded particles have the greater probability of fracture because they absorb more of the impact energy for a given loading. Size distributions of progeny show that five pebbles or more are sufficient to predict the distribution of most particles in small energy regimes. Cumulative impact testing shows that considerably more energy is required to break a rock through cumulative damage than through a single impact?this is of considerable importance in the light of the indications from DEM simulations that most breakage in a mill will be from cumulative damage rather than single impact breakage.

Jan 1, 2006

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003