Search Documents

By F. Qunfei, W. Laijun, X. Lyu, A. Cosmos, L Huijuan, Z. Jinggang, G. Yao

In this paper, four cyanide-utilising bacteria strains were isolated from a gold mine tailings pond, in the Hexi gold mine (Shandong), China. Based on the analysis of 16S rRNA gene sequence, four strains were identified as Aeromonas hydrophila strain C1, Bacillus mojavensis strain C3, Shewanella oneidensis strain C2, and Aeromonas media strain C4. Based on the cyanide detoxification efficiencies results of the four strains, Bacillus mojavensis C3 had the highest detoxification rate and was selected to assess its efficiency to detoxify cyanide in gold mine tailings at different pH (9.5, 10.5, and 11.6) using cyanide as the sole carbon and nitrogen sources. Strain C3 was capable of detoxifying 46.5mg/L of cyanide-containing gold mine tailings at all tested pH ranges at 30oC, 196 rpm after 15 d. The amounts of cyanide detoxified were 87.5%, 84.1%, and 73.5% at initial pH 9.5, 10.5, and 11.6, respectively. The highest cyanide detoxification was observed at pH 9.5. The viable cells growths in the samples were 5.7E+09CFU/mL, 4.9E+09CFU/mL, and 2.7E+09CFU/mL at pH 9.5, 10.5, and 11.6, respectively. Free ammonia concentrations were observed as a byproduct of the biodetoxification process. The residual ammonia concentration in the sample was observed at 0.35 mg/L, 0.33 mg/L, and 0.62 mg/L at pH 9.5, 10.5, and 11.6, respectively. The highest residual ammonia concentration was noticed at pH 11.6. The amount of cyanide removed by mixed culture strains C3 and C4 was 94.6% and showed a residual free ammonia concentration of 2.6mg/L, as biodetoxification byproduct after 120 h. The pure culture Bacillus mojavensis strain C3 and its mixed culture strains exhibited higher potential to detoxify cyanide-containing gold mine tailings at alkaline pH values and could be cultivated to detoxify gold mine effluents at large-scale. Keywords: Bacteria strain, cyanide, detoxification efficiency, gold mine tailings

Jan 1, 2020

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By N. A. Barcza

INFACON 7, the seventh International Ferro Alloys Congress, took place in Trondheim, Norway, in June 1995. The main aim of the Congress, which was held under the auspices of Euroalliages and the Norwegian Ferroalloy Research Organization, was to present the challenges facing the ferro-alloys industry on the road to the 21st century. Halyard Tveit, Chairman of the Technical Committee, summarized these as: ? the transition to a single global market economy ? new demands with regards to quality arising from customer needs, and ? increased awareness of the global environment. In the Plenary Sessions Kouichi Nakamura (Nippon Steel) outlined, from the steel industry's point of view, the relationship between technical advances in the products and more demanding ferro-alloy specifications. Advances in steel manufacturing technology and higher product quality have been supported in the past by raising the quality standards of ferro-alloys. Future requirements are bound to bring about more severe standards, and these need to be established by common agreement between both industries.

Jan 1, 1996

By B. M. V. Baloyi, D. Mchabe, D. Chetty

South Africa accounts for the largest global manganese ore production share, primarily from its Kalahari Manganese Field deposit. Despite this, domestic smelting is beset by energy constraints, resulting in most ore being exported for smelting. Mintek is investigating energyefficient pathways for ore reduction, specifically undertaking prereduction tests to reduce energy consumption for manganese smelting. The present contribution considers the effect of methane, anthracite, and holding time, at a fixed temperature, on the extent of reduction of Mamatwan-type ore, primarily from a mineralogical perspective. In particular, the aim was to carburise the monoxide Mn phase to Mn carbide, as this is less energy intensive than producing metallic Mn from the monoxide. Based on thermogravimetric test results, the ore and products from three experiment sets were analysed using X-ray diffraction and scanning electron microscopy to assess the phases and textures present. The findings show that carburisation of manganese monoxide and its equivalents is most advanced under conditions of 8% anthracite, 10% methane, and 60 minutes of holding time, thus confirming with the thermogravimetric data. These results show promise for reducing energy consumption for Mn smelting in ferromanganese production.

Mar 4, 2025

By C. Musingwini, A. S. Nhleko, P. M. Muke

Open-pit mine planning includes the determination of a long-term open-pit mine production scheduling (OMPS) plan. The OMPS plan is generally a three-dimensional (3D) block extraction sequence that seeks to maximise the net present value (NPV) of future cash flows, while complying with technical and operational constraints. The OMPS problem is computationally complex because it involves the analysis of large datasets, while simultaneously incorporating both multiple hard and soft constraints. The OMPS problem has been solved using deterministic or exact approaches, heuristic, and metaheuristic models. When compared to heuristic and metaheuristic models, deterministic approaches tend to take much longer to solve the OMPS problem when the number of constraints increases. Therefore, this paper presents a metaheuristic model which utilises a genetic algorithm (GA) framework to solve the OMPS problem. The GA-based model was applied to the Newman1 and Zuck Small mining instances, which are publicly available from the online MineLib database. The NPVs for the OMPS plan generated using the GA-based model for the two case studies were compared to the best-known published MineLib solutions obtained using the TopoSort heuristic model at the time of this study. For the Newman1 instance the equivalent annual NPVs were approximately US$6.6 million for the GA-based solution and US$5.1 million for the TopoSort solution. For the Zuck Small mining instance, the equivalent annual NPVs were approximately US$99.8 million for the GA-based solution and US$102.5 mil for the TopoSort solution. These results show that the GA-based model produced comparable solutions to some of the best-known solutions, thus, indicating strong potential application of GA-based models to solve OMPS problems.

Sep 1, 2021

By N. Snyders, I. Mwandawande, S. M. Bradshaw, M. Karimi

"Computational fluid dynamics (CFD) was applied to predict the average gas holdup and the axial gas holdup variation in a 13.5 m high cylindrical column 0.91 m diameter. The column was operating in batch mode. A Eulerian-Eulerian multiphase approach with appropriate interphase momentum exchange terms was applied to simulate the gas-liquid flow inside the column. Turbulence in the continuous phase was modelled using the k-_ realizable turbulence model. The predicted average gas holdup values were in good agreement with experimental data. The axial gas holdup prediction was generally good for the middle and top parts of the column, but was over-predicted for the bottom part of the column. Bubble velocity profiles were observed in which the axial velocity of the air bubbles decreased with height in the column. This may be related to the upward increase in gas holdup in the column. Simulations were also conducted to compare the gas holdup predicted with the universal, the Schiller-Naumann, and the Morsi-Alexander drag models. The gas holdup predictions for the three drag models were not significantly different. IntroductionColumn flotation is an important concentration technology that is used in the mineral processing and coal beneficiation industries. The growing interest in the use of column flotation in mineral processing has been attributed to the simpler flotation circuits and improved metallurgical performance compared to conventional flotation cells (Finch and Dobby, 1990). Flotation columns have also found other applications outside mineral processing, such as de-inking of recycled paper (Finch and Hardie, 1999).In column flotation, a rising swarm of air bubbles generated by means of air spargers is employed to collect the valuable mineral particles and separate them from the gangue minerals in a countercurrent process. Wash water, which is continuously fed at the top of the column, is used to eliminate entrained particles and stabilize the froth. The column volume can be divided into two sections – the collection zone in which the bubbles collect the floatable mineral particles, and the cleaning zone (or froth zone) where product upgrading is enhanced through the removal of unwanted particles entrained in the water mixed with bubbles from the collection zone."

Jan 1, 2019

By F. Samimi Namin

One of the main tasks in exploitation of mines is to select a method suitable for the deposits, specific features including geometric, geo-mechanical and geological features. The purpose of selecting a mining method at this stage is to choose one or more method(s) having the most coordination with the deposit?s conditions and external factors, including the allocated budget and local technology for detailed feasibility studies. Several methods have been developed in the past to evaluate suitable mining methods for an ore deposit, based on its physical characteristics. These approaches can be classified into three groups: (1) profile and checklist methods, (2) numerical ranking (scoring) methods, and (3) decision-making models. Most of these methods have shortcomings. Considering the fact that most of the specifications of mineral deposits, such as dip and depth, are linguistic variables, absoluteness of the explaining parameters by previous methods can be mentioned as the most important disadvantage of these methods. This paper discusses the Fuzzy technique for order performance by similarity to ideal solution (Fuzzy TOPSIS) to determine the mining method. The fuzzy decision making (FDM) software tool is employed to develop a Fuzzy TOPSIS based model. Application of this model with various values (crisp, linguistic and fuzzy) of the deposit eliminated the existing disadvantages of other methods. Two empirical illustrations demonstrate the effectiveness and feasibility of the evaluation procedure. These show that the proposed model performs better than its alternatives. Keywords: mining method selection, fuzzy TOPSIS, decision making, mining engineering, linguistic variables.

Jan 1, 2008

By D. F. Malan

Considerable practical knowledge and effective use of empirical evidence is required in the design of tunnel support systems. In many instances, it is unclear how individual support elements interact with fractured rock and which elements of the support system are critical in controlling and containing the movement of material proximate to the excavation. The present paper outlines a displacement discontinuity approach that allows the coupling of surface constraints, in the form of liner or mesh material, to an explicit representation of time-dependent rock discontinuity creep movements. The method is illustrated for a simple square-shaped tunnel profile in which the fracture zone is mobilized by an imposed stress field. A crucial aspect of the model is the computational treatment of the coupling between the liner material and there presentation of the fractured rock mass. This allows the response of the liner material to be assessed quantitatively in terms of the possible reduction of movement in the rock mass. The importance of installing the liner timeously after the excavation is formed is illustrated in a specific example. A number of computational difficulties in simulating liner-rock interaction mechanisms are identified.

Jan 1, 2008

The vast majority of the roughly 100 million rock anchors installed in mines in the USA each year use resin cartridges1. About 4.5 million of these bolts are installed using a mechanical shell in addition to the resin to create an active (pre-tensioned) bolt. Over 1 million of the bolts are passive cable bolts and typically have an effective grout length of 1.2 m, regardless of the cable length, which could be as long as 6 m. The successful performance of the resin grouted bolts depends on several parameters, including the annular gap between the bolt and hole wall, which should be relatively small, ideally from 3 mm to 5 mm. This requirement, combined with the high viscosity of the resin, produces a high back-pressure that can cause the bolt being installed to buckle or not be installed to standard. It is this back-pressure that limits the effective grout length with passive cable bolts and causes the mechanically anchored bolt failures (typically called ?spinners? where the mechanical shell does not anchor). This creates potentially unsafe conditions and wastes time and money. A purpose, built rig was used to mimic underground installations and record the back-pressures during full scale applications in the laboratory. This information was used, and is still being used, to reduce the failures and sub-standard installations by producing improved designs. In addition, a flow model was calibrated that can act qualitatively to estimate the back-pressures and can be used as a crude screening process before full scale prototypes are built and tested. To date, the results obtained have been used to stop the use of a mechanical shell due to the proven higher rate of failures. A new, improved mechanical shell is being field tested and another system is underdevelopment. The use of the rig is therefore ongoing to develop improved mechanical anchor systems. It is too early for real data; however, anecdotal evidence seems to indicate that significant improvements can and will be made.

Jan 1, 2011

By S. Andika, O. A. Putri

Maintaining fleet productivity, which consists of balancing loader and truck performance, has always been a challenging task. An automatic dispatching system (ADS) is implemented to help monitoring fleet condition and assign trucks to a designated loader. Integrated data from real time Global Positioning System, Vehicle Health Monitoring System, and other production related data are acquired to support the ADS. However, the abnormal truck cycle has been the main culprit which resulted in unnecessary loader hanging time and trucks queuing time. Hanging and queuing time accounted for 2.34 and 2.07 minutes respectively per loading cycle or equal to 2,861 loose cubic metres per fleet per day production losses. Using integrated dispatching system data, the authors conducted research to study a truck’s hauling cycle that affects fleet productivity. The data is modelled to obtain the arrival rate pattern in a front loading area by adopting the queue theory algorithm. This paper aims to understand the potential pattern of a truck’s cycle abnormality and to resolve its occurrence.

Sep 1, 2021

Spiral concentrators are compact, cost-effective and generally efficient gravity concentration separators for a wide range of applications (for example: coal, beach sands, iron ore, chromite and tantalite). Large mineral processing plants consist of thousands of spiral concentrators resulting in large plant footprints (capital intensive) and the adjustment of splitters is time consuming, impractical and is in many cases neglected?high capacity (HC) spiral concentrators aim to address these shortcomings. As a result Exxaro Namakwa Sands is currently investigating high capacity spiral technology for the spiral circuit upgrade at the primary concentrator plants (PCPs). This article summarizes the rougher spiral performance evaluation that was conducted on different types of spiral concentrators (the traditional MG4 spiral concentrator and the high capacity (HC) spiral concentrator) under different feed conditions. In addition, the effect of slimes on the spiral concentrator performance was also investigated. Slimes rheology was linked to the poor concentrator performance at the higher slimes concentrations. The test campaign shows a sacrifice in recovery under design-feed conditions can be expected when using high capacity spiral concentrators in the rougher stage when compared to traditional spiral technology currently in use. Both spiral concentrators show a detrimental impact of slimes on the performance, but the high capacity spiral concentrator is more sensitive to the higher slimes conditions.

Jan 1, 2010

The Proceedings of the above Symposium have been edited and published by the Symposium Committee. The Symposium was sponsored by the Australian Coal Association, the Joint Coal Board, and the United Nations Economic Commission for Europe. The Symposium was very well attended, with presentations from fourteen countries, including all the major coal-producing countries of the world. The Proceedings are presented in two parts: the Symposium Part and the Workshop Part. The Symposium Part deals basically with the theoretical aspects of outbursts and high-gas emissions in mines, while the Workshop Part is more practically oriented and describes case studies, and the management systems, and drilling technologies used in underground mines.

Jan 1, 1996

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

By M. Karsten

Platinum mines in the Bushveld Complex are located in areas with a high geothermal gradient. This means that, compared to, for example, gold mines of the Witwatersrand region, high rock temperatures are encountered at relatively shallower depths. Thus air cooling and refrigeration need to be considered at early stages in mine development. Another factor that influences air cooling and ventilation requirements is the use of trackless diesel equipment for loading and hauling broken rock. At shallower depths it will be more cost-effective to locate the cooling and ventilation equipment on surface, whereas for deeper mines the more cost-effective option is to locate cooling equipment underground. For intermediate depths, trade-off studies need to be undertaken to determine the optimum mix between more cooling and less air or more air and less cooling, as well as the optimum location for this cooling equipment. Factors that are taken into account include power requirements, positional efficiency, and additional infrastructure requirements. Traditionally the approach has been to ventilate ?all of the mine all of the time?. However, with increasing power costs and growing pressure to ensure sustainability, this strategy must be modified to apply ventilation and cooling on demand. In other words, both cooling and ventilation equipment should be operated only when needed and should be adjusted to the demand at the time. Obviously there will be areas that will need to be ventilated (and cooled) continuously (for example, for dilution of flammable gases), but this can be built in to the overall strategy. In addition, in devising ventilation on demand (VoD) strategies, occupational criteria relating to exposure to gases, noise, and heat need to be taken into account. This paper discusses options available for implementing energy-efficient ventilation and cooling systems and suggests ways of changing traditional thinking in the overall ventilation and cooling of mines. Efficient ventilation and cooling designs can play a major role in improving sustainability and reducing energy costs and carbon footprint.

Jan 1, 2012

By K. Thambi

"A recent amendment to Section 36(11)(e) of the Income Tax Act, 53 of 1968 (Tax Act) now extends the allowable deduction of ‘capital expenditure’ incurred by mining companies pursuant to the Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA). In terms of the Taxation Laws Amendment Bill 2016 (TLAB 2016), the allowable deduction has been extended to include expenditure incurred on infrastructure in terms of Social and Labour Plan (SLP) requirements as per the MPRDA. Interestingly, what necessitated the amendment was the need to recognize SLP requirements and to circumvent administrative difficulties for mining companies and the South African Revenue Services (SARS) in differentiating the use of developmental infrastructure by employees or the community. The successful implementation of such a deduction hinges on a sound SLP system. However, given the challenges within the current SLP system, this amendment could be considered somewhat premature. IntroductionSection 36(11) of the Income Tax Act 58 of 1962 (Tax Act) enabled mining companies to deduct certain capital expenditure in lieu of its other sections. In particular, it made provision for mining companies to deduct capital expenditure incurred pursuant to the Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA), but excluding capital expenditure incurred in respect of infrastructure or environmental rehabilitation. As such, mining companies could only deduct such capital expenditure that related directly to their employees and not to the wider community (Clegg, 2018).In terms of the Taxation Laws Amendment Bill 2016 (TLAB, 2016) (South Africa, 2016a), the recent amendment to Section 36 extends the relief provided under section 36(11)(e) to include capital expenditure incurred on infrastructure in terms of the Social and Labour Plan (SLP) requirements of the MPRDA. In other words, the capital expenditure incurred by the mining company for the benefit of the people living in mining communities. To qualify for such a deduction, the infrastructure erected or developed by the mining company should reflect what was agreed between the mining company and the Department of Mineral Resources (DMR) as per the SLP requirements of the MPRDA (TLAB 2016)."

May 1, 2019

By S. Mohanta, B. C. Melkap

"SynopsisDry beneficiation of coal by air dense medium fluidized bed is an emerging trend. It is widely believed that the particle size of the medium has a significant effect on the separation efficiency. This investigation demonstrates that medium particle size has a major effect on separation efficiency. Experimental results show that different size fractions of the same feed respond differently to the same size fraction of medium solids. Furthermore, a particular size fraction of feed coal responds differently with different size fractions of medium solids. The Ep values and overall metallurgical performance parameters, obtained from experimental results, clearly indicate the superior performance of an air dense medium fluidized bed separator when using –150+106 µm magnetite powder as the fluidizing medium. These observations reinforce the importance of sizing the medium particle size for the air dense medium fluidized bed.IntroductionIn an air dense medium fluidized bed (ADMFB), a fluidizing bed of a particular density is created by suspending solid particles in an upward air flow. A feed containing coal particles of different densities is introduced into this fluidizing bed. The particles with relative density less than the bed density float on the top of the bed, while particles denser than the bed density sink through it. Since there is a general correlation between ash content and density of coal particles, it is possible to remove ash-forming impurities from a raw coal to the required level by regulating the density of the fluidizing bed. Recently, the ADMFB process has received significant attention world-wide for its specific advantages of low operating cost and less restrictive for small capacities (Luo and Chen, 2001; Houwelingen and de Jong, 2004; Dwari and Hanumantha Rao, 2007; Sahu et al., 2009; Mohanta et al., 2012). This process is not recognized as a well-established industrial practice because of the availability of efficient wet processing technology. However, with the revival of interest in dry beneficiation of coal in general, and ADMFB in particular, there is a concerted effort to improve the efficiency of the ADMFB process, and successive improvements have made the process a competitive and viable option for beneficiating coal."

Jan 1, 2015

"SAMPLING: THE IMPACT ON COSTS AND DECISION MAKING1. INTRODUCTIONFor years those in the minerals industry have been taking samples to assist them in making decisions; whether they be about investing billions of rand in a new mining operation, or simply whether a truck load of mineralised material should go to the mill or the waste dump, - we need a sample to help us make our decisions. This paper emphasises the importance and significance of sampling as a process, some of the associated technical problems and some of the advantages, especially in the light of traditional approaches that has usually left mine sampling to the least educated and lowest paid individuals on the mine. Perhaps the most important aspect that requires attention is the variability, usually measured in terms of precision, that tends to infect the sampling procedures. Francis Pitard 12 has stated: ""There is no such thing as reliable feasibility studies, unbiased ore grade control, accurate environmental assessments or effective process control, if you cannot identify and minimize the seven (ten) major sources of sampling variability. "" It is these ten sources of sampling variability and the way they arise that are briefly investigated. Variability is measured in terms of variances and rather than being self-compensating, there is good evidence to indicate that they are in fact additive at every step in the sampling and analytical process."

Jan 1, 2014

By E. Van Der Lingen

This paper provides a review on coloured gold, platinum, andpalladium intermetallic compounds, and discusses the models thatwere developed to obtain these materials. These compounds have acrystal structure of high symmetry, such as the CaF2or CsClstructures, ensuring distinct electron band structures. Variousexamples of coloured gold, platinum, and palladium intermetalliccompounds are provided. More in-depth discussion is provided on thepurple gold (AuAl2) and yellow platinum-aluminium (PtAl2)compounds with CaF2structure, as well as the purplish-pinkpalladium-indium (PdIn) compound with CsCl structure. Precious metal intermetallic compounds are used in jewellery andprovide a new dimension to design. Some of these compounds havealso found use as barrier coatings on turbine blades for jet engines,and more recently, research has been conducted into their potentialuse as catalysts, electro-catalysts, sensors, capacitors, and fordecorative coatings.

Jan 1, 2014

By S. R. Grobler, S. Bilessuris, M. E. Greenway

Ensuring that all the head ropes on a multi-rope friction winder share the load equally has been a design and maintenance issue since they were first developed. Accurate machining of the rope grooves is necessary to meet this objective. Early analysis of the change of rope loads for ropes in grooves that are mismatched in depth treated the grooves as rigid. Groove depth tolerances deduced from this analysis are stringent and difficult to achieve in practice. Test work indicated that the inherent flexibility of groove lining materials alleviates the load-sharing problem. However, no analysis of rope load changes due to mismatched flexible grooves has been published. In this paper we develop new equations for the rope load variation for flexible grooves. By allowing flexibility to reduce to zero, the corresponding rigid rope groove equations are obtained. New criteria for tolerable groove depth variations are developed from this analysis, which depend on the flexibility of the groove lining material.

Sep 1, 2021