Search Documents

By J. H. Jacobs

This report records a chapter in the history of the development of an electrolytic manganese industry in the United States. Nearly all the manganese requirements of the United States have been imported. Although there are large quantities of manganese ore in the United States, most of it is low-grade and cannot be used for the production of ferromanganese. Since the electrolytic production of manganese carried out by a process developed in the laboratories of the Bureau of Mines offers a method whereby the extensive low-grade deposits may be utilized and since commercial development had proceeded slowly, the Bureau constructed a new and larger pilot plant at Boulder City, Nev., where abundant electric power was available. An authorization in November 1940 covered a plant of only several hundred pounds daily capacity. Additions to some sections author¬ized by subsequent appropriations have enabled the plant to produce over 2,000 pounds a day for extended periods.

Jan 1, 1946

By J. F. Barkley

Smoke abatement is a subject of which fuel technology, although absolutely essential, is only a part. Its successful accomplishment starts and ends with human factors that must be given thorough consideration; between this "start" and "end" fuel technology is applied. Smoke abatement usually starts from the desire of some person or persons to be free from uncleanness caused by the stack of someone else and ends with the sincere desire of the operator of the fuel-burning equipment to maintain a clear stack. Although "smoke abatement been discussed for many years, it is only recently that the public has been mindful of such expressions as "air pollution" and "air hygiene." The subject has duel in common with that of supplying pure water but is more complicated. The public desires pure water, expects pure water, is willing to pay for pure water, and expects to continue to pay for it indefinitely; it is a development of civilization. It is doubtless correct to say, however, that people in general do not et realize the detriment of air pollution to their well-being or give the question enough serious consideration. This is illustrated by the fact that in city smoke abatement it is the mass of small householders that sins the most and is the hardest to handle. It is rather difficult to assemble a group of people in a room without the air becoming contaminated with smoke. Smoke abatement will lag with the lack of desire for pure air - probably the biggest human factor involved in its accomplishment.

Jan 1, 1939

By A. C. Fieldner

This report is the fourth of a series of annual summaries of research and technologic work on coal by the Technologic Branch of the Bureau of Mines. The coal research program of the Bureau has been broadened and made more flexible to adapt it to changing conditions and needs of the coal industry, and as a result information as to the properties and composition of coal has been increased and new and improved practices in mining, preparation, and utilization of coal have been devised. The present

Jan 1, 1940

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan's pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By Carlon S. Land

The Bureau of Mines investigated the influence of a free gas saturation on oil recovery by water drive. A digital computer was used to calculate the combined oil recovery from solution-gas drive to various states of depletion. Results of these calculations are compared and optimum conditions for the maximum oil recovery are found for various fluid-rock systems. For most of the fluid-rock systems, the calculations show an optimum gas saturation other than zero. Using fluid and rock properties as parameters, graphs are plotted showing the optimum gas saturation and increase in oil recovery brought about by the gas saturation. The effects of fluid properties and relative permeability on the optimum gas saturation are seen in these graphs. The graphs can be used as guides in connection with other considerations in determining the optimum time to start a waterflood. They should also be helpful in determining the MER of a water-drive reservoir. The effects of compressibility and solubility of the trapped gas saturation are investigated for select cases using a backward difference scheme to solve the partial differential equation of three-phase flow. From these calculations, it is observed that some benefit of a gas saturation remains for injection pressures up to 1.5 times the original bubble-point pressure.

Jan 1, 1974

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made an the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Alastair M. Lumsden

A study was initiated to examine the ways in which a number of foreign countries classify and regulate metal/non-metal mines which experience problems due to naturally-occurring flammable gases. Twenty countries were selected for study, and useful information was obtained from sixteen of these. Nine countries were visited (five of them twice) to hold meetings with representatives of government mine regulatory agencies and mine operators, and to visit mines encountering methane and other gases (carbon dioxide, nitrogen). In the later stages of the study seven gassy metal/non-metal mines in the United States were visited so as to provide a basis for comparison, and hence the evaluation of both the U.S. and foreign gassy mine regulations. In addition to obtaining copies of the mining laws and regulations of a number of foreign countries, nine foreign gassy mines, and the seven in the United States were documented in as much detail as possible. All this information is presented, along with appropriate conclusions and appendices. The study took two years and three months to complete.

Jan 1, 1983

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972

By Robert C. Dyni

The Bureau of Mines in cooperation with the Solution Mining Research Institute conducted surface and subsurface investigations over five solution-mined salt cavities in the Hutchinson, KS, area. The purpose of these investigations was to determine the mechanisms that lead to the formation of sinkholes above collapsed solution cavities. Of the five salt-solution cavities investigated, four had collapsed and produced sinkholes prior to the time of the investigations; the fifth cavity was considered stable. Exploratory drilling and coring operations were conducted at all five sites; surface stability monitoring was conducted at three of them. The results of these studies indicate that excessive dissolution at the salt-shale contact of each collapsed cavity produced large, unsupported roof spans that ultimately exceeded the structural integrity of the overburden. The stable cavity was not exposed to excessive dissolution at the salt-shale contact; this limited the roof span and ensured a stable cavity. The data also show that surface settlement in the vicinity of the two surface-monitored sinkholes continued for approximately 7 years after the sinkholes formed, indicating that the rubble piles of the collapsed cavities were undergoing gradual consolidation.

Jan 1, 1986

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By J. C. Cawley, G. T. Homce, M. R. Yenchek, H. K. Sacks

As in many other industries, such as construction and agriculture, overhead electric power lines are a serious hazard at mining and mining-related operations. Even when excluding injuries that occur during electrical maintenance work, over one fourth of electrical fatalities in the mining industry are due to accidental overhead line contacts, and for each fatality nearly two serious non-fatal injuries occur due to such contacts. In incidents involving high-reaching mobile equipment, many of the victims touched the equipment after the fact, unaware that the machine frame had become energized by the line contact. MSHA data for accidents involving overhead power line contacts in the mining industry between 1980 and 1997 reveal that in 57% of the cases personnel were unaware of the accidental line contact until after one or more workers touched the equipment or a hoisted load and were injured. The situation is similar in the construction industry, where according to the National Institute for Occupational Safety and Health (NIOSH) data at least 20% of such victims are unaware of the line contact. This suggests that a device that alerts workers when a power line has been contacted could help prevent many of these injuries. Such a device would not prevent power line contacts, yet if widely employed could yield a significant reduction in the number of resulting injuries. Researchers at the NIOSH Pittsburgh Research Laboratory are attempting to develop such a device. The approach being investigated is based on measuring electric current flow to ground through a machine during a line contact. The specific technique being tested involves the diversion of some part of this current through a shunt cable mounted on board the machine, to provide a point at which to install a current sensor. Experiments thus far indicate that this approach is feasible. Ongoing research is better defining electric current flow through mobile equipment, refining techniques for measuring this current, and identifying factors that could limit the effectiveness of the proposed alarm.

By Charles W. Merrill

The U .S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By Charles W. Merrill

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By David Bendersky

This report covers the activities of a feasibility study of fiber optics technology fur use in mines. The objective of the study was to evaluate, both technically and cost-wise, the possible use of fiber optic technology for underground mine communication and monitoring systems. The first phase of the study was devoted to the collection of information on the present underground mine communication systems and monitoring techniques, and the status of applicable fiber optic technology. In the second ph se of the study, a communication and monitoring system for a hypothetical underground coal mine was designed and the costs estimated. The significant findings and conclusions are presented.

Jan 1, 1982

By Arnold M. Lansche

[Selenium and tellurium are rare elements in the earth&apos;s crust. Their scarcity and primary dependence of supply on copper and lead output are in consonance with the relatively small quantities consumed at 1964 level. Production depending on output of copper and lead creates a supply situation- which would appear to militate against development of large-scale usage of these elements. However, supplies have adequately met. demand in the past decade and can be increased substantially if warranted by new uses for either selenium or tellurium Ores of copper and lead re the principal sources of selenium and tellurium. Byproducts from the smelting and refining of copper and lead concentrates are incorporated in refinery anode slimes from which selenium and tellurium metal are recovered.]

Jan 1, 1967

By Michael J. Sapko, William D. Monaghan, Michael A. Trevits

Mine seals are used extensively in underground coal mines to segregate mined-out areas and to isolate fire zones or underground areas that are susceptible to spontaneous combustion. Over the years, 30,000 mine seals have been erected in underground coal mines in the United States. Mine seals, along with rock dusting and ventilation, represent the fundamental means of preventing underground coal mine explosions. In this study the National Institute for Occupational Safety and Health (NIOSH) used ground penetrating radar (GPR) technology to determine if each of three test mine seals were uniformly constructed. Three mine seals representing different construction methods and materials (cast-in-place foamed cement; solid block, polyurethane foam and gravel; and wire mesh, rebar and gunite) were erected at the NIOSH Lake Lynn Laboratory’s underground mine as part of an on-going research program. The seals were imaged using GPR with 400-, 500-, 900-, and 1,000-MHz antennas. We found that variations in uniformity existed in the material for the cast-in-place foamed cement seal. Variations in uniformity also existed in the seal made from solid block, polyurethane foam and gravel. The post-processed radar records correlated closely with recovered core samples (areas of gravel and polyurethane foam, and areas containing only polyurethane foam). Finally, the radar records of the seal made of wire mesh, rebar and gunite showed the various components. The results of this work suggest that GPR could be used as a tool to evaluate mine seal characteristics and construction uniformity.