Search Documents

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By Steve Brace

Electronic detonators have been commercially available to the mining industry worldwide for over ten years. It is estimated that total cumulative global sales will have reached 25 million units by the time of the Conference in February 2004. This is below 0.2% of all detonator types sold during this period. Perhaps 20 million will have been used underground in South African gold, diamond and platinum mines. These will have been produced by South African companies, in South Africa for South African customers. Here efforts have met with greater success and in 2003 fully 5 million, or 3% of local detonators sold, could be of an electronic type. However, it is estimated that about US$7.00 (R50.00) has been expended on R & D, manufacturing facilities and marketing, for each unit so far sold. Large sums of money continue to be spent. Despite the apparent success in South Africa, is it justified? Electronic initiation systems have not produced significant technical benefits to the end-user underground nor corporate profits to the supplier. Some doubt they ever will (even from the large surface operations where the price per unit is much higher). A conclusion might be that they have failed. In 1998 Smit and Pistorius wrote a paper titled “Implications of the Dominant Design in Electronic Initiation Systems in the South African Mining Industry”. This ISEE paper seeks to summarise and review the conclusions of the earlier work. These were: that a dominant design had not yet emerged; the type of connector and the way in which detonators are connected and programmed would be a strong determinant influencing the development of a “winning” product; technical aspects rarely solely determine which becomes the dominant design (marketing, social and economic factors often have a strong influence); electronic initiation systems were an emerging technology for the underground gold mining industry in South Africa and because it was under severe cost pressure the mines would look to them to raise productivity and hence profits; finally, as a dominant design begins to emerge, one could expect a number of players to exit from the industry.

Jan 1, 2004

By P. N. Worsey, M. Schmidt

Many advanced military systems and civilian power generation concepts postulate the availability of compact sources of electrical power capable of delivering gigawatts over microsecond time scales. For example, such a compact power source is essential for future practical pulsed high-powered microwave sources. An explosive-driven flux-compression power generator (EDPG) could fill this requirement. A basic strength of this concept capitalizes on the inherent high energy density storage capacity of modern chemical explosives. It relies on the physics of magnetic flux compression to convert that stored chemical energy into very large amounts of electrical power over short time scales. The generator also has the additional advantage of employing the same types of explosives that are already routinely used in conventional munitions. However, the self-destructive nature of this type of power generator places serious limitations on power pulse-lengths and ranges of applications. This paper describes how a multi-disciplinary team led by researchers from the University of Missouri-Rolla (UMR), Texas Tech University (TTU), and Texas A&M University was awarded a grant by the U.S. Air Force Office of Scientific Research to perform basic research to resolve several fundamental EDPG problem areas. Described are the utilization of UMR’s extensive explosives research expertise and facilities to investigate questions of energy conversion efficiency and the mechanics of energy production. Also, UMR explosives researchers will provide inputs to improved dynamic computer models of the complex, intertwined physics and chemistry operative in these devices. In addition to explosives expertise, UMR provides facilities for basic explosives material research, as well as the storage, machining, and formulation of explosives. UMR researchers are also using test facilities and data collection equipment at the Rock Mechanics and Explosives Research Center and at the UMR Experimental Mine to perform “proof of principle” and subscale tests of explosive-driven flux-compression power generator components. An integral part of the paper is a description of the development of an extreme intensity flash system by UMR and TTU to allow for the high-speed photography of EDPGs in operation. This multi disciplinary research program offers major advances regarding the size, weight, and electrical characteristics of compact EPDGs. Such breakthroughs could dramatically accelerate the practical realization of systems currently under study. Also, these power sources may have far reaching relevance to other Department of Defense and certain commercial compact power applications.

Jan 1, 2000

By Anne Caroline Costacurta Polli, Jose Rojas Cáceres, Roberto Mahler de Morais, Thais Costa Silva

The technology and the knowledge about the behavior of explosives and detonation accessories allowed to create new products for different situations by the restrictions imposed by the market. In a Brazilian underground copper mine the restriction occurred in the use of high grammage Det Cord in the development heading blasts perimeter holes. Enaex Brazil has developed Densiex UG™ (Low-Density Bulk Emulsion), a water-resistant bulk gassing emulsion with a density ranging from 0.60 to 0.90 g/cm³ to replace the high grammage Det Cord in blasts. That product is pumped in the same Mobile Manufacturing Unit (MMU) as Enaex Brazil's standard underground (UG) bulk emulsion. This product has a Lower Velocity of Detonation (VOD), vibration, and detonation pressure, which contributes to a better finishing of the drift, lower impact in the support structures, and lower generation on unstable rocks in the perimeter of the drift. This case aims to summarize the results of the work on the application of the Low-Density Bulk Emulsion in perimeter holes in an underground development gallery at an underground copper mine in Brazil. During this work, 10 horizontal drift blasts were performed using the Low-Density Bulk Emulsion, which presented an average density of 0.64 g/cm³, increasing safety, a 25% reduction in overbreak, a 23% reduction in scaling time, elimination of rework, and a saving of $135,000 per year for this business partner that immediately implemented this new product in all blasts at this mine.

Jan 21, 2025

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine.

Feb 1, 2020

By A. Lindo, M. Held

The formation of NOx fumes is an undesired occurrence and is dependent on a variety of variables. Methods for detection of such fumes with blast analysis tools are available using color schemes for grading, but no quantification tools to measure concentration and cloud totals exist today. In cooperation with DIRS (Digital Imaging and Remote Sensing Laboratory) at RIT in Rochester, NY, Austin Powder has been looking for methods and techniques to identify and quantify total amounts of NOx by capturing cloud activity via a video feed from a drone in combination with measuring NOx and subsequent cloud modeling (i.e., plume segmentation). To accurately measure fume events, Austin Powder and the RIT team have been collaborating in performing small scale blasts at an Austin test facility and then transferring knowledge learned to full scale blasts at customer sites. The collected data will allow to identify any relationships between the total amount of explosives used and the quantity of NOx produced. The analysis of the total amounts of NOx and identification of blast areas those fumes originate from will help to better understand key factors that contribute to their occurrence as well as to quantify the severity of such events. By quantifying the magnitude and concentration of fumes generated by non-ideal detonations, the blasting technique can be optimized to minimize unwanted environmental effects and improve public perception of blasting as a necessary component of societal progress

Jan 1, 2024

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Allen Kinney, P. T. Freeport

This paper presents the methodology for final wall-controlled blasting utilized at the Grasberg Mine. The resulting optimized slopes representa14%and17% increase to bench face angle (BFA) and inter-ramp slope angle (ISA), respectively. The corresponding increase in both copper and gold recovery was more than 40% greater than forecast for each material. The Grasberg open pit mine is located in the remote jungle province of West Papua Indonesia, at an elevation of 4,200 meters(13,780 ft).With a diameter of approximately 3.5km(2.2 mi), anddepthover1.2km(0.7 mi),P.T. Freeport Indonesia (PTFI)has mined billions of tons of rock from one of the world’s largest gold and copper deposits. Grasberg Operation and Engineering implemented a quality driven slope optimization program for the final pushback, with the goal to safely increase recoverable metal through steeper slopes, while utilizing existing infrastructure and equipment. This paper focuses on controlled blasting initiatives, blast monitoring, and as-built slope measurement tracking, although many groups contributed to the success of Grasberg slope optimization. The potential slope optimization area was divided into two sections based on geologic assessment: Area A at radial 200°-270° and Area B at radial 270°-360°. Original slope designs for areas A and B specified ISAs of 51° and 52°, respectively, with all BFAs in the pit at 70°. Through continuous development, collaboration and achievement, the Grasberg final pit accomplished a BFA increase to 80°for all areas, and an ISA increase from 51° to 56°in Area A, and 52°to 60° in Area B.

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By Felipe França Sitonio

Parameter’s control of explosives used in blasting operations have become more relevant over the years, bringing a better understanding of detonation performance. Giving into consideration that bulk emulsion density’s variation reflects directly on blasting results due to its importance in product sensitivity and velocity of detonation (VOD), blast designs are conducted assuming that cup density measurements are reliable and explosives gassing agents will perform as per specifications. Nevertheless, confinement conditions in boreholes like temperature, presence of water and surrounding circumstances of rock mass are often neglected on predictive modelling and off-site measurements. This paper describes the assembly of a device equipped with pressure sensors and its utilization in confined boreholes of an open pit mining operation, aiming to obtain in situ monitoring of density variation in several explosive columns. After we developed a software to get and process data of a hardware prototype and the device functionality was validated in water, oil and quarry mining experimental trials, 7 of 291 boreholes in a gold mine operation were chosen to be monitored with two probes each, placed at the top and at the bottom of the explosive column profile. The results obtained enabled a comparison between the bulk emulsion density variation when acting in different environments, since we selected boreholes with diameter of 101.6 mm (4 in) and 139.7 mm (5.5 in) and some with presence of water. Besides the increase of explosive density with depth related to hydrostatic pressure increase, we found an overall error of 6% in cup density measurements when compared with sensors placed at the bottom of boreholes and 2% when compared with sensors placed at the top of explosive column. These findings provide detailed insights into how bulk emulsion explosives behave in different circumstances including depth and borehole diameter, giving the opportunity to re-evaluate blast design parameters such as its geometry, sequence pattern, charging profile and explosive composition.

Feb 2, 2020

By R. F. Favreau, Favreau Patrice

"The economy profits from the rock excavated in mines and quarries and the excavations required for the construction of roads and buildings. However such excavations are achieved by blasting withexplosives, and explosions create fly rock and vibrations which in some cases may throw rock far intoinhabited regions and may vibrate buildings excessively in these regions. Society, however, no longeraccepts that their quality of life be disturbed by the risks of fly rock or the perturbation of vibrations.Thus it is important to know how to design blasts that do not cause excessive fly rock or vibrations, and to understand why sometimes a blast does create excessive vibration or fly rock. An article presented at the 2015 ISEE (reference 1) explains how unacceptable vibrations can be avoided, while the present article explains why dangerous fly rock occurs and how it can be avoided. The article shows by rigorous calculations with the blast simulator Blaspa that long range fly rock can be due to short collar or short burden, but mainly it explains how inadequate blasting that allows the floor to rise can cause even further reaching fly rock, a situation not usually recognized by most blasters."

Jan 1, 2016

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By Stuart Brashear, Robert Brush, Ben Cook

In early 1993, the Piney River quarry owned and operated by the Blue Ridge Stone Corporation of W.W. Boxley, received a series of complaints from the owners of a 130 year-old historic farmhouse that had been converted into a bed and breakfast establishment. Since the distance from the quarry to the farmhouse was substantial, a unique method of seismic data acquisition was utilized to determine if perceived blast effects were caused by air blast or low amplitude, low frequency ground vibration.

Jan 1, 1995

By Jean M. Bouvet, Pierre M. Vuillaume

There is not just one ANFO: ANFO explosive behaviour depends significantly on the blasting conditions and on its physico-chemical characteristics. For instance, ANFO effficiency increases whereas AN porosity is higher and consequently loading density of the explosive is less. This can be argued against generally admitted ideas. Therefore, the efficiency of industrial explosives related to ANFO (for example "relative weight strength" or "relative bulk strength") is a tool that must be used with caution.

Jan 1, 1993

By D T. Froedge

This paper is a presentation of a coyote shot at the Oriskany Sand Quarry of the Pennsylvania Glass Sand Corporation, Berkeley Springs, West Virginia.

Jan 1, 1982

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addresssed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1990

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012