Search Documents

By Z. Sawlowicz

Finely dispersed, primary sulphide mineralisation in the Cu-Fe sulphide zones of copper-bearing shale of the Polish part of the Permian Kupferschiefer is mainly present in the form of framboids and spherules. This type of mineralisation is especially well preserved in organic-rich shale, where it often dominates over a later diagenetic mineralisation that consists of large grains and veins. In microscopic observations special attention was paid to composite grains of copper and iron sulphides. The results suggest that the Cu-Fe and Cu sulphides precipitated in the Kupferschiefer sediment before pyritisation of the framboids had ceased and that they replaced metastable precursors of pyrite. The precipitation of copper sulphides could have been delayed owing to the formation of Cu-organic complexes.

Jan 4, 1992

By D. G. Skinner, J. H. Griffiths, F. T. Williams, A. G. Withers

"The absence of homogeneity, in dust-clouds underground indicates the use of a method in which the volume of air sampled is an appreciable proportion of the total volume under consideration. Of the available methods, only the impinger and gravimetric techniques seem to comply with this requirement. In practice, greater efficiency of collection of the smaller particles is possible by the use of a gravimetric filter than with the impinger. For this reason if, as seems desirable, a standard method of sampling be sought, the adoption of a gravimetric technique is to be recommended.Provided that the amount of dust collected is reasonably large, the paper filter would seem to be preferable to the solid crystal type of filter on account of its greater convenience in use.Alternative methods of sampling are desirable to cover the wide range of practical conditions."

Jan 1, 1947

By J. Drzymala, K. L. Wolters, T. Chmielewski, T. D. Wheelock, D. H. Birlingmair

Microflotation tests were conducted with a modified Hallimond tube equipped with a fritted glass disk and magnetic stirrer to determine whether the results would support an equation that predicts a linear relationship between particle size and the reciprocal of particle density in water for a specified flotation recovery in a given time. Data obtained with the tube for either hydrophilic or hydrophobic solids fit the equation satisfactorily. It was also shown that the natural flotability of molybdenite is somewhat less than that of elemental sulphur and that sodium dithionite is a good depressant for sulphurised pyrite. In addition, it was found that the untreated pyrite and galena used in the study were hydrophilic and did not float by particle-bubble attachment.

Jan 4, 1992

By D. J. Allan, W. R. Wilson

For conventional aerospace aluminium alloys of the 2000 (copper) and 7000 (zinc, magnesium) series the recycling of process scrap from both metal suppliers and aircraft manufacturers is a well-established, worldwide industry. The recent introduction of a new family of alloys that incorporates lithium has posed a new challenge to the recycling industry owing to the high cost of lithium, its high reactivity to the atmosphere and to refractories and its absence from the specifications of all other registered alloys. Various process options for recycling have been identified, but vacuum distillation has been selected as the most cost-effective and technically feasible solution. Experimental work established that the separation of Li from AI-Li scrap is feasible and an industrial process has been designed. The economics of Li recovery are very sensitive to the AI-Li content of the feed material. Owing to the design of aerospace vehicle manufacturing plants it is expected that the swarf will be mixed with other alloys. A method of enriching this feed has been developed that is based on the control of swarf morphology by thermal and mechanical treatments as a precursor to eddy-current separation. After eddy-current separation and vacuum distillation small proportions of Li are retained in the AI residue. The effects of this on the properties of conventional AI-Si shape-casting alloys were investigated and safe threshold levels have been established.

Jan 4, 1993

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By R. Winand, P. Harlet

he cathodes produced are of electrorefined grade; metallographic structure and surface roughness are controlled to a depth of 1.3 cm (single-side deposits); silver levels in the cathode are regulated by the presence in solution of Cl- and Br- ions; organics must be used at very low concentrations (around 0.1 mg/l with a consumption of about 0.01 mg/l/hr). The required concentrations of additives were established according to a well-defined strategy based on the consumption of organics at the cathode by a mass transfer limited-process.

Jan 4, 1992

By R. Phillips

The low concentration of diamond in workable deposits requires very large samples for grade estimation, and results, even then, may be erratic and difficult to interpret. Although the Poisson probability distribution cannot accurately describe the occurrence of diamond, it is suggested that it gives a better estimate of grade than conventional methods, even from single samples. Examples illustrate the simple calculation required.

Dec 1, 1971

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By A. B. Holland-Batt

Two graphical techniques which are commonly used to assess batch separations are analysed in terms of reaction kinetics to provide a more powerful method of evaluation. An alternative and more general approach, based on the selection and application of suitable efficiency criteria, is also presented. The method proposed distinguishes between selection and collection efficiency in flotation and can be used to estimate the degree of liberation in the feed. Two examples are given: table concentration of monazite and ilmenite from a beach sand, and flotation of a pyrite-haematite ore

Dec 1, 1971

By R. E. T. Hill

"A laboratory study was undertaken to determine the condensed equilibrium phase relations at 600°C in that portion of the quaternary Fe-Ni-Cu-S system which lies in the neighbourhood of the monosulphide solid solution (MSS). The study sought to determine to w hat extent copper affects the temperatures of stability and compositions of iron-nickel sulphides in bulk compositions similar to those of massive Fe-Ni-Cu ores. Experimental data, including stable phase assemblages and phase compositions, are presented.In the quaternary system at 600°C MSS forms stable phase assemblages with pentlandite, chalcopyrite solid solution, pyrite and vaesite. Over the range of bulk compositions displayed by natural ores copper as well as metal/sulphur ratio have a significant effect on the thermal stability of pyrite and pentlandite. Errors therefore accompany the widespread practice of ignoring copper or chalcopyrite when the mineralogical and compositional changes that have accompanied the initial cooling of primary magmatic sulphides or their subsequent homogenization during isochemical metamorphism are being deciphered. These errors are most significant for ores the bulk compositions of which lie tow ard the sulphur-deficient side of the cupriferous MSS. Temperatures as much as 300°C above the copper-absent value are possible for the interpreted upper stability limits of pentlandite in these ores.The experimental data show that up to 2.0 at% copper can occur in pentlandite stable at 600°C in a bulk composition equivalent to natural magmatic ores. This is equivalent to nearly 10 vol% chalcopyrite. Pentlandite contains more copper than coexisting MSS and the copper content of both phases increases with increasing iron."

Jan 1, 1984

By P A. Collier

The general view of the author is that all the good intentions of manufacturers can fail completely if the variations in circumstances in underground mining are not considered at all times. With a belief that it is the customer that has the experience and know ledge of problems which occur on long installations. Reilloc talk with customers in coal mines around the world, and have done so from their inception. With considerable experience in their home market, their technical approach was received with enthusiasm by coal companies in both Australia and South Africa, and whilst experience was obtained in other countries, it is the particularly close working relationship in these two areas that is covered in this paper. The refinement of manufacturing techniques and the fine tuning of the specification to which the chain is made was developed in conjunction with factual underground experience obtained by customers as they sought to improve their productivity and a reduction in working costs. With a reliable product the mines are able to concentrate on improved operational techniques to extend the useful working life and plan for multi-panel usage of the chain.

Jan 5, 1996

Jan 1, 1984

By L. T. Matthews, C. E. Loo

During sintering, porous ore particles are easily assimilated by liquid melt. Two simple models of the process are considered: the dissolution of a solid by a liquid and the penetration of a liquid into a porous solid. Laboratory sintering studies covering a range of experimental conditions were undertaken to characterise the assimilation of large particles of ore and flux by melts formed from different mixes of fines. For ores, the process appeared to be complicated by the detachment of fines from the ore surface prior to melt formation, according to the mass of adhering fines and surface roughness of the particle. This delayed the onset of assimilation and sometimes reduced it, although melt penetration was fast and effective. Studies using different temperature profiles suggested that the assimilation of haematite was controlled by the transport of Fe2O3 away from the surface of ore particles. The assimilation of limestone depended more on thermal conditions than on the three magnesia-bearing minerals considered. Changing the composition of the initial melt significantly altered the extent of assimilation of ores and limestone, but again had a less marked effect on the magnesia-bearing fluxes.

Jan 8, 1992

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993

By A. D. Read

Selective flocculation was investigated as a possible method of recovering values from mineral slimes which are too finely divided to be treated by conventional mineral processing methods. It has proved possible to flocculate selectively either haematite or a silicate from a stably dispersed mixture by varying the anionic character of the high-molecular-weight, partially hydrolysed polyacrylamide employed. Different separation methods have been developed for hard and soft water media. Electrokinetic and infrared techniques have been employed to elucidate the mechanism whereby selectivity has been attained in the different cases. The following influences on the various selective flocculation parameters have been investigated: (a) the level of the different reagent additions and (b) the shear conditions during and after flocculant addition. A feature of the particular system studied was the high solids content at which it was possible to achieve good selectivity. Probable reasons for this are advanced, and the possibilities and potentialities of the process are discussed.

Dec 1, 1971

By S. G. Tsimas, A. K. Moutsatsou, S. G. Tsivilis, G. K. Parissakis

(NH4)2SO4 can be used with success as a leachant to remove gypsum contained in celestite ores. The process, which is applied before flotation, provides an upgraded feed and problems related to the simultaneous flotation of CaCO3 and SrSO4 are reduced. The process is independent of the gypsum content of the feed so that each leaching stage decreases the gypsum content by almost 50%. The use of (NH4)2SO4 has an insignificant effect on the co-leaching of SrSO4 (0.45 wt.%) at each stage

Jun 13, 1905

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

By A. C. Dunham, Y. D. Drakapoulos, P. W. Scott

The Pt and Pd occur alloyed with copper in small, irregularly-shaped grains, 0.25-5.0 micrometers in maximum dimensions. Grains of unalloyed native copper are also present. The grains are completely surrounded by or marginal to magnetite with inclusions of Ni-Fe-Co sulphides and native Ni-Fe, which is apparently a product of the serpentinisation process. Crystallisation of the Pt-Pd-enriched copper probably occurred at the same time, at low temperature, but the previous form of the Pt and Pd is unknown as no earlier PGE phases have been found. While Pt and Pd minerals are usually important in early-magmatic base-metal sulphides, Pt alloyed with Cu is extremely rare and apparently occurs only very late in the paragenetic sequence. A Cu alloy with Pd dominant over Pt and only minor amounts of other elements appears not to have been reported

Jun 14, 1905