Search Documents

O. S. GARRETSON, Buffalo, N. Y.: If I may judge from the half-tone illustration engraved from a photograph of this medal and accompanying Dr. Prazer's paper, I do not think the cast ing is exceptionally fine. I have often made castings of simi lar character which I think were equally good. For instance, I have taken a coin, moulded it directly in fine sand, and cast from it in Scotch (or the equally good, if not better, Ameri can Scotch ") foundry-iron a copy quite as sharp and smooth as the original. The secret is in using very fine sifted sand. In fact, I have used for this purpose the dust which had accumulated on the beams overhead in my foundry, riddling it with a very fine sieve before using it. ['NOTE BY THE SECRETARY.—After the session at which these remarks were made by him, Mr. Garretson cast at his Buffalo foundry, in the presence of a number of members of the Institute, copies of the bronze pin furnished to visiting members by the Local Committee of the Buffalo meeting. The accom panying illustration, Fig. I, has been reproduced from a photograph of such a casting, made in green sand, under the conditions of ordinary foundry-practice, and not subsequently polished in any .way. I can also certify that the photo graphic negative was not touched, to improve its clearness of definition, before the production of the " half-tone" plate from which Fig. 1 has been printed. As, in the case of the Kytchtym medal, it was the thin, ribbon-like sprue, rather than the low-relief features of the medal itself, which indicated the fluidity of the metal and the sharpness of the casting, so in this work of Mr. Garretson it is the long and slender pin which offers the strongest evidence of these qualities. It is scarcely neccssary to point out that the filling in the mould of a long and nar row opening, such as this pin presents, is the severest test that could be imposed upon the casting, and that the sharpness of the point of the pin in the casting is striking evidence of the success with which this test has been met. The Pittsburgh Testing Laboratory .has made for the American Manufacturer measurements of this casting and an analysis of the sprue. The thickness of the main casting is from 0.049 to 0.068 inch. That of the tag bearing the stamped number is 0.024 inch. The analysis, which represents the iron ordinarily employed by Mr. Garretson for thin castings, is as follows :

Jan 1, 1899

By Anna Sukhanova, Svetlana Babaeva, Sergey Andreev, Victor Beltenev

"The Zenith-Victoria /1/ and Jubileynoye /2/ hydrothermal fields have symmetrical structural position on the Mid Atlantic Ridge (Fig. 1). In order to compare the evolution of hydrothermal systems, we conducted mineralogical and geochemical studies of SMS from both sites.Radiochemical and geochemical investigations of massive sulfides of the Zenith-Victoria field distinguishes three major stages of evolution: initial, interim and final represented by Fe-S, Cu-Fe and Zn-Fe types of SMS respectively /3/. In this talk, we describe the results of geochemical analysis of massive sulfides from the Zenith-Victoria field. Geochemical varieties of SMS are considered to be indicators of the evolutionary stages of the hydrothermal system."

Sep 1, 2014

By J. R. Campbell

The need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. Washability Studies The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money can hardly be spent on "feed surveys') to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus. The sizes to be examined to get the picture are optional to the investigator. In modern wet washing, the range is from 4 to 0 in. Hand-picking on properly constructed belts is perhaps the standard for cleaning above these sizes. A good picture of the coal may be obtained by the following screen analysis: 3½ to 1¼ in. 1¼ to 3½ in. ½ to 5/16 in. 5/16 in. to 14 mesh 14 to 28 mesh 28 to 48 mesh and for very complete data on the fines: 48 to 100 mesh 100 to 200 mesh and through 200 mesh

Jan 1, 1930

The Health Tracking project is one of five projects being undertaken as part of the Minerals Industry Cooperation Initiative (MICI) û a national initiative sponsored by the Minerals Council of Australia. The aim of the Health Tracking project is to assess the practicality of ways to demonstrate the monitoring of hazardous exposures and the occurrence of related occupational illness and disease and development of management systems and strategies at a national level. This second stage of the project will be completed in 2005 and will cover four areas: pilot development of a comprehensive job exposure matrix (JEM) for the minerals industry; development of both proactive and reactive occupational illness and disease metrics; recommendations regarding appropriate health tracking models; and provision of best practices guidelines for management of occupational health. The synergies between these areas will establish the path towards an effective national occupational health surveillance system and the development of effective prevention strategies and policies.

Jan 1, 2005

By J. A. Singmaster

IT will perhaps be wise to define my terms in begin-ning to talk about my subject, especially so where the popular and commercial terminology are as con-fused as they are in the case of zinc. While our French friends know zinc by its true name, and we find Balzac, Daudet, and other literary celebrities using it correctly in their novels, it is quite the contrary in English, particularly here in America. The quotation of a definition for zinc recently appearing in one of our leading technical magazines, "zinc is the place where they wash the dishes," will emphasize the difference. Zinc suffered in the first place by becoming an article of commerce long after its alloys with copper were in common use under the name of brass. Then again, when the art of zinc coating iron and steel objects was commercialized, we called it galvanizing, which is really a meaningless term. The French and Germans use the obvious terms-zinguerie and verzinken-for the opera-tion. Since these two uses of zinc, brass making and galvanizing, have been by far the largest consumers of zinc, is it any wonder that the popular knowledge of zinc is as vague as it is? In fact, since the disappear-ance of the sheet of zinc along with the parlor stove, the zinc-lined bath tub and refrigerator, there has been little popular contact in this country with the undis-guised metal zinc. On the Continent, where zinc has been used for over a hundred years under its real name, particularly for roofing and building purposes, the situ-ation is quite different. It is quite refreshing to turn for a moment to the contrast offered by my friend, Dr. Merica's specialty, nickel. They put 2 or 3 per cent of it into steel, and we have nickel-steel, or a larger amount into an alloy, and we have nickel-silver. To be sure there is no silver there, but what need that matter, nickel is used in the alloy and is first in the name. They plate with nickel and call it nickel-plating, no galvanizing about that. And, finally, they take that noble coin which admits us daily to underground New York, composed of three parts of copper and one part nickel, and get away with nickel as its popular name.

Jan 6, 1927

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By Pierre Mousset-Jones

A questionnaire was sent out to three classes of mines to determine the extent of the heat problem in U.S. and Foreign underground mines. The following list shows the replies received from this questionnaire, however not all the known hot mines in the US replied. A complete listing of the results can be seen in Appendix I. 1) US coal mines - 37 replies 2) US non coal mines - 23 replies 3) Foreign non coal mines - 36 replies. At the present time there are approximately eleven non coal and one coal mine in the US experiencing heat problems which require special efforts to maintain an acceptable working place climate. However since the survey was completed some of them have been placed on standby. The Mine Safety & Health Administration (MSHA) does not have any specific regulations relating to heat stress. Informally the American Conference of Governmental Industrial Hygienists guidelines are followed which use wet bulb globe temperature (WBGT) with values ranging from 26.7°C to 31.1°C for a moderate workload, and different rest regimes. An MSHA report (Misaqi 1976) recommended that conditions should not exceed 26.1°C WBGT for men and 24.4°C WBGT for women. However, quite recently the organizations involved with planning two of the proposed nuclear waste repositories in the United States, have opted for the criteria of an air cooling power of 300 w/m2, and a WBGT of 27'C respectively.

Jan 1, 1986

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By J. S. Contreras, E. Córdova, I. Gottreux, A. Anani, A. Ferrada

Cave mining is an underground mass mining technique. The largest projects, which are known as ‘super caves’, produce hundreds of thousands of tons of ore per day, which involves large footprints with considerable column height, and have a life of mine of over 20-40 years. These operations are typically located deep, under high stresses and in competent rock masses, making initiation and propagation of the caving process harder to manage. These challenges must be confronted by optimizing the fragmentation of the orebody to achieve smaller size blocks that will result in consistent caving and improved flow of the ore from the drawpoints. To achieve better performance from the drawpoints, preconditioning is applied to fragment and damage the material required to cave. We present a proposed design for preconditioning in underground mines, considering the challenges that these large-scale mines are already facing, based on a comprehensive analysis of current design parameters, case studies, and sensitivity analyses using numerical models.

Feb 2, 2021

By Gaudin. A. M., S. C. Sun

THIS paper presents the results of a study of the relationship of the electrokinetic or zeta potential to flotation phenomena. The relationship is established on the experimental evidence that mineral behavior in flotation and in cataphoresis is generally governed by the chemical properties and amount of the reagents adsorbed at mineral surfaces. Cataphoresis1-5 or electrophoresis is the name given to the movement of a charged particle in a liquid medium under the influence of an applied electric field. Mineral behavior in cataphoresis, as indicated by the magnitude and sign of its ionic charge, can be represented by the term zeta potential. In this paper, the zeta potential represents the difference in potential between the immovable liquid layer attached to the surface of a solid particle and the movable liquid layer in the body of the liquid, and is the result of the tendency of ions on the surface of the particle and within the liquid boundary layer to establish a condition of equilibrium. A high positive zeta potential means that the mineral surface is dominated by cations, a high negative zeta potential indicates domination by anions, and a low zeta potential indicates that the surface is influenced almost equally by cations and anions. In terms of observed quantities the zeta potential is given by the relation [z = 47ruu(300)$ Kx] in which z is the zeta potential expressed in in volts, u the viscosity of the solution in poises, u the velocity of particles in centimeters per second, x the impressed potential gradient in volts per centimeter, and k the dielectric constant of the solution in c.g.s. units. A convenient source for the derivation of the equation is the book by Thomas,6 The term zeta coefficient is an expression coined to denote the difference between the magnitude of the zeta potential of a mineral suspended in solution A, and that of the same mineral suspended in solution B, which consists of solution A and an additional chemical agent, but is at the same pH. For example, the difference between the zeta potential of galena particles in distilled water and that in any chemical solution at the same pH is a zeta coefficient. Or, when the zeta potential of a mineral particle is measured first in distilled water, then in a mixture of water and copper sulphate, and finally in a mix-

Jan 1, 1946

By M. A. Cook

Crude titanium metal, produced by the reduction of titanium tetrachloride with magnesium, is contaminated with some excess magnesium end adhering magnesium chloride when it is removed from the reaction pot. The method of vacuum 'purification is described in which the crude mixture is heated in a vacuum at a temperature of about 1,700° F. and the magnesium metal and chloride are volatilized away from the titanium, leaving it practically magnesium-free in a sponge-metal form. The pilot-plant equipment is described in detail, together with the technique of operation and methods of sponge recovery. Operating data is given, which compares ten 24- to 30-hour heats with ton 48-hour heats, and finally, power and labor requirements are discussed. Vacuum purification of raw titanium produced by the Kroll process has boon employed for treating of several tons of raw titanium with results for superior to those achieved by the method of leaching and grinding. The operations described, while on but little more than pilot-plant scale, indicate commercial feasibility of the process, even though it is a batch-typo operation. All equipment is either of standard manufacture or can be readily fabricated from standard materials, and operation of the units can be satisfactorily maintained by semiskilled labor.

Jan 1, 1952

By A. L. Marshall, F. J. Norton

THE object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C.oin a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. APPARATUS AND TECHNIQUE The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 0800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard' glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not 'a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by

Jan 1, 1944

By Walter Fuchs

IT is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds ;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2 : I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. SYNOPSIS OF BIOLOGICAL AND CHEMICAL FACTS The biosphere is not sterile; i.e., microorganisms are always present. Microorganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life-proteins, fats, carbohydrates, lignins, waxes, resins may serve as a habitat of microorganisms. In the decomposition of a medium. some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17, 32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1941

By Ernesto Bacigalupo

Kallpa Generación S.A. (Kallpa) es una empresa dedicada a la actividad privada de generación de energía eléctrica, ubicada en el distrito de Chilca, provincia de Cañete, Lima que opera la central termoeléctrica del mismo nombre. En ese sentido, el presente texto describe el proyecto de conversión a ciclo combinado que va desde el ciclo simple a ciclo combinado de la C.T. Kallpa. Este ciclo consiste en la coexistencia de dos ciclos termodinámicos (ciclos de producción de energía mediante vapor y gas) en un mismo sistema, de manera que el calor que genera uno, lo aprovecha el otro omo fuente térmica. Asimismo, la principal ventaja de utilizar el ciclo combinado es su alta eficiencia, ya que se obtienen rendimientos superiores al rendimiento obtenido operando en ciclo simple.

Sep 14, 2009

By F. V. Lenel

This discussion is concerned with the method of manufacturing, the design possibilities, and the properties of pole pieces for direct-current electric . motors and generators made from iron powder. In such applications as pole pieces, the electric and magnetic properties of the material are of major importance, therefore they are discussed somewhat more fully. However, the main advantage in making pole pieces from powders lies in the rapid and inexpensive method of manufacturing these pieces, and in the flexibility of design, rather than in their superior electrical properties. As a matter of fact, pole pieces from iron powder have found their principal field of usefulness in small electric motors for controls and similar applications where the highest possible flux density in a given design is not required. Fig. I shows a number of different designs for pole pieces made from iron powder. The steps involved in fabricating them are: (I) briquetting—with each stroke of the briquetting press a complete . pole piece is produced; (2) sintering, and (3) sizing, which is a one-step coining operation in a hand-operated punch press. Conventionally small pole pieces are made from laminated electrical sheet steel stock by punching out the laminations and riveting them together (Fig. 2). The powder method has the advantage of being rapid and inexpensive; also, it makes possible the molding of pole pieces with a round hub, which are better from a design standpoint, as will be shown later. It is difficult to make such round-hubbed pieces from laminated stock. The pole pieces could, of course, be machined from solid stock, but this method is not widely used. The raw material for making pole pieces from powder is straight iron powder without the addition of any alloying ingredients. However, the grade of powder used is of considerable importance, as will be shown later when the influence of the grade of iron powder upon the magnetic properties is discussed. Pole pieces are briquetted in the same way that other iron-powder machine parts are made. Because the pole pieces are flanged—i.e., they have a hub and a wing section—they are made in presses that apply pressure from both ends. For best mechanical and magnetic properties, the density throughout the piece should be even and also should be constant from piece to piece. For that reason a powder of constant compressibility from batch to batch is needed for briquetting pole pieces. One method of obtaining the required magnetic properties is to sinter the pole pieces at temperatures higher than are used for most iron-powder parts. A temperature of 2400°F. and an atmosphere of hydrogen has been found satisfactory. No automatic furnaces of the roller hearth or mesh-belt type have yet been developed for such high temperatures. A box-type furnace heated with Globar heating ele-

Jan 1, 1945

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high- temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols4 it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range.

Jan 1, 1932

By Lowell B. Moon

Concern over possible wartime shortages finally resulted in passage of the Strategic Materials Act in 1939. As authorized by one section of this legislation, the Bureau of Mines proceeded to investigate deposits of seven strategic minerals with the objective of developing tonnages of low-grade material that could be mined in an emergency. During the war, the size of the program and the number of strategic minerals were increased, and the objective was the more immediate one of aiding production. Since the war, the size of the program has been reduced, but the number of minerals on the strategic list continues to be large. The objective has returned to that of 1939. In the course of the program, more than 10,000 examinations were made and about 1,300 projects were run on deposits of 33 different commodities. A considerable contribution to war production was made in six of the commodities investigated, and a minor contribution was made in twelve others. Substantial reserves have been indicated in 19 minerals. Private interest is currently active in some of the deposits developed in 14 commodities.

Jan 1, 1950

By U. Schoepf

Economic and at the same time environmentally acceptable mining of small vertical ore bodies and veins to great depths has always been a challenge for miners. The Bauer cutter system, widely used in civil engineering, has been further developed for applications in exploration and mining, to a sustainable system for selective mining with a focus on small vertical ore bodies and veins, as well as residual ore in open pit operations. Current situation of conventional mining of small ore bodies and vertical veins Small ore bodies and vertical or near-vertical ore veins often pose a challenge to the mining industry. The relatively small size of the ore deposit over great depths or lengths, with only limited exposure to the surface makes economical mining difficult. Open pit mining of such ore bodies must either be terminated early because of the high stripping ratio and the enormous environmental impact or is unprofitable from the very beginning. The required massive stripping of waste rock leads to high material hauling times and costs, intensive roadway and bench construction and maintenance, possible safety hazards due to heavy vehicle movement, pit wall stability risks, intensive surface water management and massive waste dump requirements. In addition, it can be assumed that increasingly extensive rehabilitation measures will be required in the future after mine closure. Particularly in vertically oriented magmatic and hydrothermal deposits the technical, economic and environmental limits for further pushbacks, to extend the open pit depth, can lead to an early end of mine life even if a significant quantity of residual ore is left behind. Going underground is only a viable option in a limited number of mines with very high ore values and volumes. The high development cost of an underground mine, as well as the higher underground mining costs, often prevent further mining to greater depths.

Feb 1, 2023

By Walter Fuchs

It is now generally conceded that coal is the product of deposition and transformation of debris of forests and swamps.29 Ample data are available to illustrate the metamorphosis of biochemical substances through biological action; other data show the progressive regional metamorphism existing in coal beds;25 and numerous examples of change effected by intrusion of igneous dikes into coal deposits have been established.23 However, often the relative importance of the biological and the geological factor in determining the character of the various natural coals is a debatable question. Since both biological and geological factors are ever present in nature, the problem, at first glance, would appear to resemble certain probability problems: specifically the simultaneous toss of two coins, with the biological factor as heads and the geological as tails. The probability is 2:I for the combined effect of both factors, as compared to the exclusive effect of either one, if the a priori probability is the same for each factor. This condition can be analyzed by a thermodynamic treatment of data, which may be obtained from a consideration of pertinent biological, chemical, geophysical and geological facts. Synopsis of Biological and Chemical Facts The biosphere is not sterile; i.e., microorganisms are always present. Microor- ganisms have been established in the ocean deep, under the ice of the polar regions, in the sand of the deserts, and in swamps far below the surface. The various biological media may be acid, neutral, or alkaline, and they may or may not be readily accessible to air. Microorganisms are encountered almost everywhere, except where the temperature is not within the range tolerable by microbial life. Of course, with changing conditions, the type of microorganisms will change. All chemical products of life—proteins, fats, carbohydrates, lignins, waxes, resins— may serve as a habitat of microorganisms. In the decomposition of a medium, some microorganisms macerate organic matter mechanically and remove certain constituents for their own nutrition; others decompose a large part of the organic matter but may leave certain constituents undecomposed. Some attack only certain specific ingredients of the organic matter. All of them build up cell substance. The nitrogen content of the medium largely determines the degree of decomposition. Below 1.7 per cent nitrogen, growth of microorganisms and hence decomposition of organic material is retarded; consequently organic material will accumulate.17,32 Such accumulations of organic material may give coal eventually. Coals differ in type and rank. The nature of the original vegetation and the conditions attending the transformation of the accumulated debris determine the type of coal such as bright, splint, cannel, and algal or boghead coals. Chemical analysis of representative samples of a given type of

Jan 1, 1942