Search Documents

By I. Mitov, A. Stoilova, D. Krastev, B. Yordanov

We present three technological scenarios for the recovery of valuable components from gangue, stored in the tailings dam at Kremikovtzi metallurgical plant in Bulgaria, into marketable iron-containing pellets. In the first approach the iron concentrate was recovered through a two-stage flotation process, desliming, and magnetic separation. In the second proposed process, the iron concentrate was subjected to four sequential stages of magnetic separation coupled with selective magnetic flocculation. The third route entails the not very common practice of magnetizing roasting, followed by selective magnetic flocculation, desliming, and magnetic separation. The iron concentrate was pelletized in a laboratoryscale pelletizer. Each technology has been assessed with regard to the mass yield of iron concentrate, the iron recovery. and the iron, lead, and zinc content in order to identify the most effective route.

May 1, 2021

By D. F. Malan, J. A. L. Napier

This paper describes some important aspects associated with historical underground measurements in South African gold and coal mines. Deformation measurements were used to confirm the use of elastic theory to simulate the rock mass behaviour in the Witwatersrand gold mines in the 1960s. Although a prominent time-dependent component of stope closure was measured as early as the 1930s, it was ignored owing to the benefit of adopting elastic theory. Neglecting the time-dependent response of the rock for many decades resulted in important aspects such as the effect of mining rate, the effect of advance per blast, and the need for enhanced design criteria not being explored. Recent work is only now starting to address this gap in knowledge. In-situ measurements of large coal specimens in the 1960s and 1970s indicated that a linear formula may possibly be a better approximation of coal pillar strengths. This alternative formulation was never adopted, however, as the power law strength formula was already deeply entrenched in the industry at that stage. In spite of these apparent failures to continuously generate and adopt new knowledge, a key lesson learnt is that major advances in rock mechanics will not be possible without careful monitoring of the rock mass behaviour in experimental sites. Areas requiring further research, such as pillar strength formulae for the Bushveld Complex and enhanced design criteria for the gold mines, can only be developed using extensive undergroundmonitoring programmes.

May 1, 2021

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By W. A. Smith, M. C. Bekker, C. Marnewick

Projects or project-orientated approaches have become a common form of work in nearly all sectors of economies. This has led to concepts such as ‘projectified’ and ‘project orientated’ organizations. By defining projectification of a company, industry, or economy as the share of project work in total work, one can reasonably determine the impact that project management, and by default projectification, has had on that company, industry, or economy in terms of staff optimization and allocation. This paper presents the results for such a projectification study of the South African mining industry. This sector has long been a significant contributor to the country’s economy from a gross value added (GVA) and employment point of view. Understanding the impact of projectification and the project management way of work on this industry may potentially add significant value to both the mining and project management knowledge areas. We show that although the mining industry is considered by some to operate in archaic ways, the level of projectification has increased over time, and now represents approximately one third of all work conducted.

May 1, 2021

By A. Mainza, I. Govender, Elbasher M. E. Ahmed

A mechanistic description of axial segregation in rotating drum flows remains an open question. Consequently, optimal mixing of grinding balls and rocks for efficient breakage, maximum production of fines, and slurry transport is seldom achieved. Experimental and numerical studies of granular mixtures in rotating drums identify alternating axial bands that eventually coarsen in the long-term limit. Most models of axial segregation are limited to binary mixtures and cannot always predict the logarithmic coarsening effects observed experimentally. A key missing factor is a robust description of the axial free surface profile that is valid across a wide range of flow regimes. We present a practical model of the axial free surface profile by linking it to readily-derived geometric features of the cross-sectional S-shaped free surface profile. A parametric study shows good agreement with experimental measurements reported in the literature and heuristically valid trends.

May 1, 2021

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021

By B. DANIEL MARJAVAARA, I. A. SOFIA LARSSON, ANNA-LENA LJUNG

The flow field and coal combustion process in a pilot-scale iron ore pelletizing kiln is simulated using a computational fluid dynamics (CFD) model. The objective of the work is to investigate how the thermal effects from the flame affect the flow field. As expected, the combustion process with the resulting temperature rise and volume expansion leads to an increase of the velocity in the kiln. Apart from that, the overall flow field looks similar regardless of whether combustion is present or not. The flow field though affects the combustion process by controlling the mixing rates of fuel and air, governing the flame propagation. This shows the importance of correctly predicting the flow field in this type of kiln, with a large amount of process gas circulating, in order to optimize the combustion process. The results also justify the use of down-scaled, geometrically similar, water models to investigate kiln aerodynamics in general and mixing properties in particular. Even if the heat release from the flame is neglected, valuable conclusions regarding the flow field can still be drawn.

Apr 20, 2021

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in by-product molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have reduced the possibility ofH2S gas evolution immensely. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Benchscale rougher flotation results for samples from the Sierrita Cu–Mo plant showed the best DCMTperformance at 8 kg/t of DCMT and pH=10.5 with 30 min of shear conditioning and 10 min of flotation conditioning time. The Aminpro plant model simulation confirmed that DCMT with 4–8 kg/t under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared to NaHS.

Apr 19, 2021

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted by-products generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining; (2) dyke construction schedule; (3) size, shape, and location of tailings-cells; and (4) mining and processing production targets. The results show that in creating in-pit tailings-cells designs, decreasing the mining-cells volume and increasing the number of mining-cells improve the net present value of the operation due to increased operational flexibility. The model generated a uniform schedule for ore and practical tailings-cells designs for backfilling activities. Integrating tailingscells optimization into oil sands mine planning and waste management ensures the efficient use of in-pit mined-out areas required for sustainable operations.

Apr 14, 2021

By Aldin Ardian, Mustafa Kumral, Jagjit Singh

Risk assessment of mining projects is a requirement in the mineral industries. In this process, many risk variables are timedependent, and the only available data are historical time series. Moreover, in the case of a multivariate scenario, conventional forecasting methods fail to capture conditional dependency across the variables, which is important when there is an underlying causal relationship that needs to be modeled for accurate project evaluation. Thus, we investigated the use of copulas to capture the conditional distribution of the factors involved in a mine risk assessment study. We employed a multivariate copula-based time-series approach to model several uncertain variables. The Autoregressive Fractionally Integrated Moving Average - Generalized Autoregressive Conditional Heteroscedasticity (ARFIMA-GARCH) model was used for the conditional mean and copulas were used to model the error distribution, thus capturing the collective variation and dependence pattern across the variables. The method was implemented to model gold prices, copper prices, and the 10-year US Treasury bond yields and to determine the project’s net present value and probability of being economically feasible. The proposed approach can be used for cases where simulation of multivariate time-series is conducted.

Apr 13, 2021

By G. T. Daware, M. J. Chaddha, S. P. Masurkar, P. G. Bhukte, A. Agnihotri

JNARDDC has evaluated bauxite deposits of India from the geo-technological point of view. During the evaluation studies, it was observed that bauxite deposits are associated with saprolite resources. During bauxite mining, various low-grade materials such as saprolite, laterite and low-grade bauxite are generated. These materials typically have low-alumina, high-iron oxide and high-silica content. Owing to their inferior quality, these materials cannot be used for alumina production and hence remain unutilized at the mine site. For the present study, the saprolite samples were collected from the Western Ghats bauxite deposits in India. The sintering studies were conducted on saprolite granules using a variety of parameters. The sintered granules were characterized, and their properties determined. The test results showed that bulk density, apparent density, porosity and refractoriness (PCE 1645–1659 °C) of the aggregates were within the range of refractory specifications. The feasibility tests carried out at the refractory industry indicated that the developed aggregates are suitable as refractory material and can substitute for calcined clay. Currently, high-purity clay resources used in the refractory industry are limited and fast exhausting; therefore, the industry is likely to face an acute shortage of raw materials, which will become more critical in the future. Therefore the sintered granules (aggregates) developed from saprolite, which is a mining waste, provide a low-cost, eco-friendly solution for the fast-exhausting resources of the high-purity clays. The developed process may change the Indian bauxite mining scenario because saprolite may substitute as a potential raw material for the refractory industry.

Apr 12, 2021

By Inoka E. Perera, Michael J. Sapko, Marcia L. Harris

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effectively inert a coal dust explosion, rock dust must be able to disperse as individual particles to air. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anticaking additives after being exposed tomoisture and then dried. The dusts were exposed tomoisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anti-caking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Experimental Mine (LLEM), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for 1 day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for 6 months. This report details the analysis and characterization of anticaking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber.

Apr 12, 2021

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

By C. C. Pretorius, S. Ramjee, R. J. Mostert

The study investigates the effect of prior corrosive exposure on crack growth resistance behaviour of thin sheet (3 mm thick) aluminium alloy 2024-T3 at slow strain rates. Compact tension specimens were exposed to standard corrosive environments that simulate accelerated atmospheric corrosion attack. Two corrosive environments were considered – an exfoliation corrosion (EXCO) solution and a 3.5 wt% sodium chloride solution. The unloading compliance R-curves of the two-hour EXCO-exposed specimens revealed a significant degradation of approximately 11% in the crack growth resistance behaviour (Kc_e values) compared to the baseline (air-exposed) values. Furthermore, secondary intergranular crack formation was also revealed in the plastic zone ahead of, and adjacent to, the crack tip of these specimens; which formed during the crack growth resistance loading. It is postulated that the observed degradation of the Kc_e values of the EXCO-exposed material is due to hydrogen embrittlement since the exposure times for the EXCO evaluation were limited to ensure that uniform corrosion dominated; that is, significant penetration of corrosion damage and pitting due to localized corrosive attack did not occur. The sodium chloride-exposed specimens revealed a similar degradation (13%) after 24 hours exposure. However, slight intergranular corrosive attack and isolated pitting were observed on the exposed surfaces prior to crack growth resistance loading, resulting in notch effects that could assist in crack growth. Pitting and intergranular corrosion were, however, not observed at the pre-crack tip. The relative contributions of the notch effects and the hydrogen embrittlement during the degradation of the KR performance are, therefore, unclear.

Apr 1, 2021

By M. N. Mathabathe, A. S. Bolokang, C. W. Siyasiya, R. J. Mostert, G. Govender

The b-solidifying g-TiAl intermetallic alloys of nominal composition Ti-48Al (binary alloy), Ti-48Al-2Nb (ternary alloy), Ti-48Al-2Nb-0.7Cr (quaternary alloy), and Ti-48Al-2Nb-0.7Cr-0.3Si (quinary alloy) (in at.%) were developed. The materials produced were tensile tested at room temperature. The as-cast microstructures and fracture surfaces of the tensile tested specimens were examined using conventional metallographic methods. Microstructural examination indicated that the alloys were comprised of lamellar structures (a2+g) embedded in columnar dendritic cores in the as-cast condition. However, the quinary alloy contained a Ti5Si3 second phase. The alloys exhibited no detectable ductility during tensile deformation, indicating the brittleness of all the materials. The fracture surfaces revealed that the alloys failed by translamellar fracture with correspondingly few cleavage facets.

Apr 1, 2021

By Ian Farrell, Josh Stowe, Eric Wingeard

Tailings transport system design is generally based on identifying the minimum and maximum process boundary conditions for pump selection and pipeline sizing. The approach is robust and well-proven. However, the approach has the potential to skew selections to operating scenarios that have a very low likelihood of occurring, such as the combination of high solids throughput and low tailings solids concentration. The approach can result in a tailings transport system design that is overly conservative. A probabilistic method-based approach captures the independent variability of design inputs and the combined likelihood of outcomes. This approach identifies the process conditions that have the highest likelihood of occurrence and are most applicable to equipment and pipeline selections. An outline of a probabilistic-based approach to tailings transport system design and the resulting selections is provided in this article. The probabilistic-based system design is compared to the outcomes from the traditional approach. The benefits and challenges to this approach are discussed and recommendations for utilizing this approach for tailings transport system design are provided.

Mar 31, 2021

By MOHAMMAD R. H. GORAKHKI, Christopher A. Bareither, MANUEL APARICIO, Joseph Scalia IV

The focus of this study was on the evaluation of hydrologic and environmental behavior observed in GeoWaste and waste rock test piles. GeoWaste is a mixture of fast-filtered tailings and waste rock prepared as a tailings-dominated mixture. The two test piles included potentially acid-generating (PAG) waste rock and were operated for 26 months to evaluate whether GeoWaste can suppresses sulfide oxidation and production of metal-rich acid mine drainage relative to PAG waste rock. The test piles were constructed in the shape of truncated 5-m-tall pyramids with 25-m base sides and flat 5-m × 5-m top surfaces. Water content, temperature, electrical conductivity, and oxygen concentration were monitored in four layers and at five locations within each layer in both test piles. In addition, 5-m × 5-m lysimeters were installed at the base of each pile to collect leachate. Approximately 2660 mm of water was added to the surfaces of the test piles via precipitation and irrigation (irrigation ≈ 1050 mm applied at an approximately constant rate for 70 days). The measured saturation, oxygen concentration, electrical conductivity, and temperature in the GeoWaste and waste rock piles suggest more sulfide oxidation occurred in the waste rock pile compared to the GeoWaste pile. Observations from the pile experiments suggest that co-managing mine waste in the form of GeoWaste reduced acid generation compared to waste rock alone due to the lower permeability and unsaturated state of the GeoWaste pile that reduced downward migration of moisture and inhibited drainage.

Mar 31, 2021

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By Yuexin Han, Yanjun Li, Peng Gao, Yongsheng Sun, Qiang Zhang

The non-isothermal magnetization roasting process and isothermal magnetization roasting process of siderite ore were investigated using thermogravimetric (TG) analysis and a real-time infrared gas analyzer. X-ray diffraction (XRD) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS) were used to analyze the characteristics of samples. The results showed that the decomposition degree and decomposition rate of siderite ore were vitally affected by heating rate and roasting temperature. It was determined that A1 reaction model (f(α) = 1 − α) and A3/2 reaction model (f(α) = (3/2)(1 − α)[−ln(1 − α)]1/2) were the most probable mechanism function of the non-isothermal decomposition process and isothermal decomposition process, respectively. The phase transformation and decomposition mechanism during the roasting process were evaluated. Siderite decomposed in the process of magnetization roasting, released CO and CO2, and transformed into strongly magnetic magnetite. The SEM images highlighted that as the decomposition progressed, the structure of roasted samples was destroyed, and an increasing number of cracks and pores emerged on the surface, which is advantageous to the following grinding process.

Mar 26, 2021

By J. Christophe Niyonzima, Ekata Emmanuel Edo, Sayaf Mustafa, Liqun Luo

Iron and manganese both are important ferrous metals, and they usually need to be extracted separately for better usage. Ferromanganese ore from the Yunnan Province of China was investigated by subjecting it to reduction roasting, leaching, magnetic separation, hydrometallurgical separation process, X-ray diffraction (XRD), electron probe micro-analysis (EPMA) and scanning electron microscopy/energy-dispersive spectroscopy (SEM-EDS). It is noted that the ferromanganese ore contains valuable components or elements of 21.41 wt%Fe2O3 and 19.88 wt%MnO, which are 14.99% and 15.40% of the total of Fe and Mn, respectively, with a large amount of impurities comprising 33.00 wt% SiO2, 9.81%wt%Al2O3, etc. After roasting, microscopic examination showed the presence of haematite, magnetite, pyrolusite, psilomelane, hollandite, marcasite, pyrite, limonite, braunite and manganite, while XRD analysis showed that the magnetite content increases with the increase in roasting temperature, reflecting the increase in conversion of haematite to magnetite. Based on EPMAand SEM-EDS analysis, it was shown that the haematite and magnetite interface were the main Fe-bearing minerals; however, the dissemination of the two minerals, that is, haematite andmagnetite with the coexistence of Fe- and Mn-bearing minerals, will result in difficulty in effective separation of Fe and Mn. The effective roasting temperature and roasting time were 800 °C and 60 min, respectively, to avoid the formation of a composite oxide of MnxFe3-xO4 beyond 800 °C. The Fe recovery via roasting and magnetic separation only was 66.56%, whereas a combination of magnetic separation which ensued after the leaching process showed a recovery of 80.08% and 59.95% of Fe and Mn, respectively.

Mar 26, 2021