Search Documents

By P. N. Anyalebechi

"The effects of solidification rate, initial melt hydrogen concentration, and grain refining on porosity formation in aluminum alloy 2024 have been investigated with unidirectionally cooled laboratory-size ingots. The ingots were prepared from melts containing hydrogen concentration of 0.059-0.27 cm3/100 g and solidified at 0.2-37 °C/s. As expected, the amount of porosity, average pore size, and pore number density increased with increase in melt hydrogen concentration and decrease in solidification rate. However, the effect of solidification rate was greater at the very low melt hydrogen concentration (0.059 cm3/100 g). These results are consistent with reported effects of solidification rate and melt hydrogen content on porosity formation in other aluminum alloys. Interestingly, addition of grain refiner slightly increased the amount of porosity and the average pore size, especially at solidification rates above 1°C/s. IntroductionIn shaped castings and wrought products fabricated from ingots, billets, bars, or slabs of aluminum and its alloys porosity formation is a problem. This is because it compromises their tensile strength, fracture toughness, and fatigue properties [ 1-18]. The pores are usually the crack initiation and propagation sites [6,8,9] and the largest pores tend to dictate the fatigue life of the aluminum products [9,10,14]. Porous regions within an aluminum product probably yield first due to the reduced tensile load bearing capacity, causing the concentration of the strain near the voids which subsequently results in premature fracture. In aluminum alloy ingots, billets, bars and slabs porosity formation is particularly problematic because of its persistence through fabrication and potential for reappearance or exacerbation during subsequent thermal treatment processes before and/or after fabrication [19]. In fact, persistence of microporosity is a serious problem in large thick plates of wrought aluminum alloy products that must be rolled from correspondingly large direct-chill or electromagnetic cast ingots. Some of these thick plate products are machined into large aircraft components that are required in service to withstand multi-directional stresses and to possess high fatigue strength, fracture toughness, resistance to stress corrosion cracking, and strength in the short-transverse direction [1,20]."

Jan 1, 2011

By Wang Shulan

The synthesis process of BaTiO3 from TiO2 and BaCO3 in the molten NaOH-KOH at 350oC was studied by the A.C impedance technique. The A.C. impedance of molten NaOH-KOH (xNaOH = 0.36) and the variation of the conductivity of the salt with time during the synthesized process were measured. The synthesized reaction of the BaTiO3 and the decomposition reaction of BaCO3 are fast and were finished in 10min. The interaction between TiO2, BaO and BaTiO3 and the molten salt was confirmed by the variation of the conductivity.

Jan 1, 2005

By Djona M. Gaballah I.

Selective chlorination of unroasted and roasted spent hydrorefming catalysts was studied between 300 and 600°C using the following gas mixtures : C12+CO, C12+N2 and CI2+air. Such materials contain Co, Ni and Mo compounds supported by alumina and/ or silica. They also contain variable amounts of V compounds, C, S, etc., accumulated during the life time of the catalyst. Direct oxychlorination of the C+S rich sample allows higher extraction rates than those obtained by the carbochlorination of the same roasted one. It seems that the roasting step doesn't favor the economic metals' recovery. Results of the chlorination of C+S poor spent catalysts, in the presence of CO, in the chlorinating gas mixture, or of carbon added to the sample, were comparable. Cobalt and nickel chlorides were .extracted from the chlorination residues by their dissolution with acidified water, whereas molybdenum and vanadium chlorinated compounds were recovered by selective condensation from the vapor phase. The recovery rates of valuable metals as well as the selectivity were higher for the chlorination of spent catalysts than results obtained by the hydrometallurgical processing of the same sample. Results of the scale-up of the oxychlorination of the unroasted sample confirmed those of the laboratory scale. The global recovery rates were about 88 pct of cobalt, 93 pct of molybdenum and 76 pct of vanadium. The carbochlorination was applied to the recovery of W and Ti from Denox catalyst that is a carbon and sulfur free one. Recovery rates higher than 99 pct at temperatures lower than 500 °C could be obtained. This may indicate that the chlorination process can be applied to the treatment of various industrial wastes or by-product containing transition and/or refractory metal compounds A flow - sheet for the pretreatment of these materials is proposed.

Jan 1, 1995

By Katie Schumacher, Greg Roset, Dayle Flynn

The Columbus Processing Complex of the Stillwater Mining Company began operations at Columbus, Montana in 1990 based on electric furnace smelting treating a precious metals concentrate from the nearby Stillwater mine and mill. Since that time, the smelter plant has been expanded in stages in order to treat recycled materials in addition to the concentrate. This paper describes a number of changes made at the plant to effectively handle recycled materials.

Jan 1, 2014

By F. J. J. van Loo, A. A. Kodentsov, J. A. van Beek, M. R. Rijnders

"A periodic layered morphology of the reaction zone has been observed in several annealed solid/solid diffusion couples, including metal/metal and metal/ceramic couples. This morphology is characterized by a regular array of alternating layers, which are either single-phase layers or bands of particles embedded in an intermetallic matrix phase. A description of several systems showing periodic layer formation is given. It is shown that the periodic layered structure with the single phase layers and the one with the bands of particles have a different mechanism of formation.IntroductionSolid state reactions in ternary systems can produce a variety of reaction zone morphologies if there are two or more reaction products. Three types of morphology have been described in detail: 1) simple layered; 2) isolated precipitates in a singlephase layer; 3) interpenetrating columnar (lamellar) or interwoven structure. Understanding the factors that govern the formation of different morphologies is of importance in many fields of engineering. For solid state displacement reactions the conditions governing the formation of these morphologies are well understood [1-4]. For example, the development of a layered or aggregate reaction zone depends on the relative diffusivities of the components through the reaction products.This paper is concerned with the periodic layered morphology which has been observed in various solid state systems. We consider this to be a fourth type of reaction layer morphology. Two manifestations of periodic layered morphology may be distinguished. One form consists of regularly spaced layers of particles of one reaction product embedded in a matrix phase (another reaction product). The other form consists of single-phase layers embedded in a matrix phase. It will be shown that each manifestation has its own mechanism of formation. In section A we consider a system (Ag/Ti-foil/Si) in which periodic layer formation will be explained as a special case of the Liesegang phenomenon. In section B we consider systems where the periodic layered structure has a different origin."

Jan 1, 1996

By Grégory Miette

The paper deals with a process that allows the recycling in a cupola of EAF dusts with 18 % Zn. It produces dusts with zinc grade higher than 50 - 55 % and commercial cast iron with less than 200 ppm Zn, 50 ppm Pb, 0.15 % S. The paper focuses mainly on lab tests made with the aim to develop an effective formulation of self reducing - melting pellets. With such a formulation, agglomerates develop a breaking load higher than 125 - 150 kg without any thermal treatment. Zinc and lead are volatilized in the cupola with yields higher than 95 % at 1200 OC, before any melting. Sulphur is transfemed into gas and slag. All these conditions allow to lower zinc, lead and sulphur grades below the cast iron specifications. Results of first bench scale tests performed at Fonderie Piret to validate the process will be presented.

Jan 1, 2002

By H. C. Roland Kammel

Stannous sulfate electrolytes are widely used nowadays in electrolytic tin production. Characteristic features of this electrolysis process are that dense cathode deposits can only be obtained by additions of organic additives and that so called ?black mud is formed on the anode surface which leads to an increase in cell-voltage. In order to prevent excessive cell-voltages or oxygen evolution the black mud has to be removed periodically. Studies in laboratory scale have been performed about the effect of different organic additives on electrolytic tin deposition and the formation of surface layers on pure and industrial tin anodes. Results reveal that organic addition agents are effective in reducing cathode roughening as well as extending the covering time of the anode ?by black muds.

Jan 1, 1985

By Lloyd R. Nelson

The feasibility of producing low carbon (LC) ferromanganese (FeMn) by lime-'ore' melt refining of high-grade ferromanganese silicon (FeMnSi) was investigated. Thermodynamic simulations demonstrated significant benefits in moving from a single-stage ladle operation to a two-stage counter-current reladling operation (to emulate the commercial Penin Process). The theoretical alloy silicon content was predicted to be refined from 1.57 to 0.005 per cent silicon, at a 6.2 per cent higher manganese yield (yield predicted to increase from 82.3 to 88.5 per cent). Extension of this counter-current refining principle, to a multistage Counter-Current Reaction Launder (CCRL) was investigated using the Slag Metal And Gas Klnetics (SMAK) software to model the mass transfer kinetics of the multicomponent coupled reaction system. Simulation results suggested that commercial production of 50 000 tonnes per annum (tpa) of refined LC FeMn, containing less than 0.5 per cent silicon, at manganese yields of up to 90 per cent, should be feasible in a compact CCRL (7 m long by 0.7 m wide).

Jan 1, 1994

By B. C. Blakey

Unlike most hydrometallurgical slurries, those containing significant concentrations of goethite are typically highly viscous and shear-thinning, even at solid volume fractions below 5%. The viscosity may also depend upon time. These characteristics must be taken into consideration in slurry transport and heating. The technical literature is replete with apparent contradictions regarding the viscous behavior of these slurries, which may be due, in part, to variations in viscosity-measuring techniques. We present techniques that yield consistent results suitable for use in process design. A striking degree of time-dependent behavior is demonstrated for a laterite slurry. Reliable methods to design and analyze tubular transport and heating systems for time-independent slurries are summarized. Rules of thumb are then offered to account for the effects of time-dependency.

Jan 1, 2000

By Jiann-Yang Hwang

A study on microwave assisted chalcocite leaching was carried out with a microwave hydrothermal reactor. The leaching was conducted with thick mineral slurries (50-100 g/l). The leaching media is a mixed solution of CuCL2 and NaCL The investigation included the effect of leaching temperature, quantities of the minerals per unit slurry volume as well as the initial concentration of cupric ions were investigated. The results were discussed and compared with that using conventional leaching method.

Jan 1, 2003

By W. Kasprzak

Modern light metals processing technologies are very complex and involve a diverse set of variables that must be quantitatively evaluated. The most effective way to design new casting processes that deliver specified metallurgical and mechanical properties is to develop a method of simulating the "real-time" process within a test sample of sufficient size. The results can then be analyzed and the required optimizations can be performed. This paper presents a novel method of simulating the industrial casting processes in a laboratory environment using an experimental apparatus based on the principle of high frequency induction heating. The applicability and accuracy of the proposed analytical method is demonstrated, for example, by simulation of the solidification and heat treatment of a test sample composed of two dissimilar materials. The simulation can be used to develop a stress model for an engine block made from an aluminum based alloy with iron cylinder liner inserts.

Jan 1, 2002

By P. Myllykoski, J. Nylander

"A commercial program package called Crownoff for the simulation of temper rolling in four high mills has been verified against measured data. The agreement between measured and calculated transversal strain distributions of the strip was found to be good. Effects of the strip crown and work roll bending force on the strain distribution were simulated. The results showed that when a single ground camber of work rolls is used for all strip widths; the strip crown should be parabolic, excluding the edge drop. An increase or decrease of the strip crown by 30 % during a coil can be compensated by a 2 to 5 t change in the work roll bending force. The ability to control the strip crown by work roll bending was insensitive to strip width. IntroductionCold rolled steel strips are usually temper rolled after recrystallization annealing, which follows cold rolling. The purpose of temper rolling is to suppress the yield point, finish the strip surface and correct possible flatness errors. The presence of a yield point might otherwise cause problems during subsequent forming processes. The in homogenous yielding in non-temper rolled steels leads to the formation of Lüders bands in the strip surface.The rolling force is influenced by the rolling speed and changes in frictional conditions in the roll bite. Therefore it is very important to plan carefully the mill settings and control algorithms during rolling. The purpose of mill control algorithms is to ensure constant reduction and the best possible strip flatness during the entire coil.Correctly predicting the rolling force is important for determining the mill presettings. Torque, forward slip and power requirements are not usually critical, if the reductions are small. However, the large elastic deformations occurring in the roll bite make the physical description of the process difficult. Physical rolling models developed for cold rolling contain assumptions that lose their validity as the reductions decrease to the level of one per cent."

Jan 1, 1994

By M Philip Schwarz

"This paper reviews the status of computational modelling of a variety of common metals reduction processes, namely the blast furnace, rotary kiln and fluidised bed, and one new process not yet commercialised, namely smelting-reduction as in the HIsmelt Process. In each case, the last decade has seen the emergence of the capability to simulate the processes using multi-phase reacting computational fluid dynamics techniques. In some cases this capability is still in the process of being developed, and the next few years will see the maturing of the modelling techniques. As they become established, it will be possible to apply them to further refine the older technologies such as blast furnaces and rotary kilns, and assist in the optimisation, commercialisation and acceptance of the newer technologies such as fluidised bed and molten bath reduction. The development of a computational fluid dynamic model of bath smelting-reduction is described in some detail to illustrate how a large number of complex and interacting phenomena can be successfully simulated within a CFD framework. IntroductionPyrometallurgical reduction processes, such as the iron blast furnace, have become increasing more sophisticated through the centuries, so that today they are often highly efficient. There are continuing pressures, however, to refine existing processes and develop new ones. The imperatives are often economic, given that the long-term trend in the price of metals is always downward. In recent times, there has been the additional need to improve the environmental impact of metal production. Given that they almost inevitably require the use of carbon, metal reduction processes are large sources of greenhouse gases, and even a relatively small improvement in efficiency can be valuable in reducing CO2 production. Local environmental issues, such as the need to control of particulate emissions, are also driving incremental improvements in equipment.In addition to the economic and environmental drivers mentioned above, new process development is also being driven by the need to process new ores, and the need to produce unrefined metal in a form more compatible with alternative routes for downstream processing. An example of the latter is the production of DR! (Direct Reduced Iron) as a feed for EAF Electric Arc Furnace) in mini-mills.Further improvement of processes that have already been honed by continual plant experimentation over many years is not an easy task. To deliver further gains in efficiency, throughput, or product quality requires a highly sophisticated tool: one such tool· is computational modelling."

Jan 1, 2001

By A. W. Bryson, K. C. Lenthall

"With the growth in the use of cobalt in industry, interest in its extraction and recovery has increased. With this increased interest comes the need for a fundamental knowledge of the processes involved in the recovery of cobalt metal. This paper examines the effects of cobalt concentration, catholyte pH, operating temperature and current density on cobalt electrowinning with respect to the current efficiency, cell potential and nature of the cobalt deposit. It is found that the cobalt concentration and catholyte pH affect the current efficiency, while current density and temperature affect the cell potential and thus the specific power consumption. Pitting on the deposit is affected by the catholyte pH and the operating temperature. Furthermore, the effect of feed flow-rate on catholyte pH, and thus current efficiency, is investigated. A model to predict the cell performance, which includes the flux of hydrogen ions through the diaphragm, is proposed.IntroductionCobalt metal is a silvery transitional metal found between nickel and iron on the periodic table. Due to its resistance to corrosion and other properties under high temperatures and its good work-hardening characteristics, it is favoured in alloys used in high temperature applications. These include aerospace, aircraft and high speed tools. Other applications include its use as a colourant in glass and ceramics, a drying agent in paints, a nutrient for livestock, a catalyst in the petroleum industry and, in the medical field, in prosthetics and radiology.The main deposits of cobalt are found in Central Africa, specifically Zaire and Zambia, although deposits also occur in Morocco, Canada and Australia. The cobalt is generally associated with other transitional metals including nickel, iron and copper. It is generally extracted by hydrometallurgical means and recovered from solution by electrowinning or hydrogen reduction. Little data [1-2] exists in literature on the electrowinning of cobalt from aqueous solutions. This paper investigates the effects of various operating conditions on the current efficiency, cell potential and deposit nature under continuous operation."

Jan 1, 1997

By T. Malvik

Norway is a big producer of ferrosilicon and silicon metal. The raw material is quartz and quartzite and large quantities from both Norwegian and foreign sources are used. The demands maade on both the chemical purity and the thermomechanical qualities of the quartz/quartzite have increased in recent years in an attempt to reduce energy consumption and to improve utilization. Control of the chemical quality of the raw material is relatively easy by means of routine analysis, but it is more difficult to find a suitable method for testing the thermomechanical properties. A rapid test method to define high quality quartzite deposits for use in the metallurgical industry has been developed. The method is based on a combination of chemical analysis, dilatometry, thermosonimetry and cathodoluminiscence.

Jan 1, 1989

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By C. Palacios

The Plant, which was started up in April 1970, was originally designed for a capacity of 40.000 ton of cathodes per annum, using 12 sections, containing 408 cells. Since then the addition of another 8 sections containing 280 cells and using the Reverse Current System has made possible the increased output of 109.000 ton. The quality of the cathodes produced is excellent. The extension of the Electrolytic Refinery, by the introduction of the Reverse Current System, has been a great success and no problem has arisen in the new equipment or in the modifications carried out in the plant. The operation of the plant has improved due to better control procedures.

Jan 1, 1976

By B. Mishra

The application of various bydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, eg. metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been 'investigated and suggested for dealing with some of these wastes' and scrap material. The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained? from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EMI' and decontamination and decommissioning [D&D].

Jan 1, 1996

By S. Seetharaman, Du Siehen

"In the processing of molten metals, it is extremely important to monitor continuously the concentration levels of various minor elements. In the production of common metals like copper, iron and aluminium electrochemical sensors involving solid as well as liquid electrolytes are being increasingly used to measure the concentrations of minor elements. The present paper deals with the electrochemical principles underlying these measurements and the possible errors involved. One of the major difficulties in the case of the solid electrolytes is to correct for the consequences of the electronic contribution to the conduction of the electrolyte.The application of the electrochemical sensors for molten metals processing involves designing of these probes to withstand the industrial operating conditions. In this respect, significant achievements have been made with respect to the design of oxygen probes for liquid metals in general and liquid copper in particular. Some of the salient design features are discussed in the paper. The application of auxiliary electrodes for impurities in molten metals like phosphorus in copper and silicon in iron are taken up. The development of oxygen sensors for slags is given special attention. Recent developments in the field of sensor technology, as applied to metals processing are highlighted.1. IntroductionThe rapid technological advancement today require precise control of the process parameters and the impurity levels. Most of the molten metals processing in industrialized countries are often steered by suitable computer models, either phenomenological or simulations based on theoretical principles. These models often require that the process parameters are continuously monitored so that the progress is followed and modified suitably as and when required. It is common practice to measure temperatures by incorporating temperature sensors at the various strategic points of the reactor. In the case of monitoring the composition changes in the various phases, the method of sampling followed by routine chemical analysis involves a time lag as well as uncertainties in sampling and analysis. In this respect, electrochemical sensors have the advantage of generating accurate data when properly applied and increasing attention is being paid in the development of electrochemical sensors for various common species in molten metals processing. In the present paper, the developments in this area over the years are outlined and typical process applications are discussed. A greater emphasis will be laid on sensors based on oxygen conducting electrolytes and their application to the production of common metals like iron and copper."

Jan 1, 1996

By Carlos M. Fontes Vieira, Ruben J. Sanchez Rodriguez, Carlos E. Gomes Ribeiro

"The worldwide demand for ornamental stones in building construction is motivating the use of their wastes, generated during fabrication, to produce compound stones. This work has as its objective to investigate the production of an ornamental compound marble (OCM) under vacuum and compression processing of a polyester matrix composite with addition of marble waste as load and as filler. Square OCM composite plates were subjected to compression and flexural mechanical tests. Samples were analyzed to obtain the density and water absorption. The OCM composites presented properties within the expected range of an artificial stone.IntroductionMarble is a limestone, composed mainly of calcite, more or less crystallized by metamorphism that ranges from granular to compact in texture. It has a density 2.7 g/cm3 and its porosity is approximately 0.4%. The UNI 8458 standard defined marble as: ""every crystalline rock constituted mainly by minerals with a Mohs hardness equal to 3-4"". In marble production around70 - 75% of whole extract material is lost in byproducts generation [1,2].In function of large volume of residues generated, the ornamental stones industry has attracted ever more the attention of environmentalists [3].Actually the marble can be pulverized to obtain calcium carbonate for industrial applications. It is also possible to obtain a thinner powder to produce concretes [l]. Some authors study the use of stone residues in concrete mortars and ceramic bricks, getting better properties to these materials [3,4].The marble residues can be also used in engineered stones, or ''agglomerated"" stones, production. The most common engineered stones in the market consist, like a polymer concretes, in polymer matrix composites incorporating petreous components. In the formulation of the engineered stones, the particulate or granular petreous components are the result of fragmentation or trituration processes to which natural stones were submitted to [ 5]."

Jan 1, 2014