Search Documents

By William R. Yernberg

The 26th Peruvian Mining Convention (Convención de Ingeneieros de Minas del Perú) was held Sept. 15 through 19, 2003, in Arequipa. The convention was sponsored by the Peruvian Institute of Mining Engineers (Instituto de Ingeneiros de Minas del Peru). The Institute has been organizing these events since 1954. They are now held every other year. The conventions spotlight Peru’s mineral resources and have contributed to the tremendous growth of the Peruvian mining industry. This year’s meeting consisted of technical sessions, forums, field trips and social activities. It was held at the Tecsup Institute of Technology of Arequipa. More than 3,000 mining professionals attended. As always, the meeting was well organized, and participants expressed gratitude to the organizing committee for another successful meeting.

Jan 1, 2004

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By Irina Chernyshova, Erik Larsen, Hanumantha Rao Kota, Vladislav Slabov, Garima Jain

The mining industry faces pressure to provide metals for the green digital shift using sustainable technologies. This study evaluates biosurfactants as collectors for ultrafine and coarser particles of hematite and malachite, aiming to improve the flotation of ultrafine particles.

Jun 1, 2023

By M. K. Larson

"Specialized numerical modeling codes have been developed over the years to estimate ground stresses during the excavation of coal in underground mines. One of these tools, MULSIM, a displacement discontinuity boundary element code, was last developed by Zipf into a version called MULSIM/NL [USBM 1992a, 1992b]. The code was used frequently in years past, but closure of the Bureau of Mines in 1996 marked the beginning of a pause in its development. A similar tool with distinctly different treatment of overburden idealization, LaModel, was subsequently developed [Heasley 1997] and largely displaced MULSIM/NL in the literature. However, recent work modeling deep western longwall coal mines [Larson and Whyatt 2013] has demonstrated that MULSIM has distinct advantages for regions with relatively stiff and strong overburden. This work required that MULSIM be revived and updated into a version called MulsimNL/Large. Updates include larger array sizes, greater precision, greater number of materials, and the addition of a five-point, six-segment pillar load/displacement model that provides the user a more flexible coal-strength model allowing hardening and softening before a final residual strength. MulsimNL/Large has the ability to calibrate to large load transfer distances observed in some western U.S. coal mines that appear to be caused by strong, massive units in the overburden and/or floor of a coal mine. Also, it provides the ability to calibrate gob stiffness to simulate measurements or estimates of overpanel weight distribution between gob and abutment, while still maintaining load transfer distance with minor adjustments. MulsimNL/Large can easily implement material strengths calculated from various pillar strength models. The five-point model gives MulsimNL/Large the ability to easily simulate pillar behavior that is extracted from detailed pillar models, such as FLAC3D. MulsimNL/Large or similar approaches should be considered for evaluating mining layouts where stratigraphic conditions are known to cause overpanel weight to transfer to an extent significantly longer than the empirical method widely used to calculate load transfer distances in the U.S. [Peng and Chiang 1984; Mark 1987; USBM 1990]."

Jan 1, 2015

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990

By José Mirão, Pedro Madureira, v Costa, Patrícia Conceição

"The exploration of seamounts south of the Azores during the EMEPC/Açores/G3/2007 campaign allowed for the collection of 30 Fe-Mn crusts from the Atlantis, Great Meteor, Small Hyeres, Irving and Plato seamounts, as well as from the East Azores Fracture Zone. These were the first samples of Fe-Mn crusts studied from these seamounts. The Fe-Mn crusts were analyzed using multiple analytical methods.The crusts are fairly homogeneous, showing typical textures for this type of occurrences. The Fe/Mn ratio, patterns and concentrations in rare earth elements, and the great homogeneity of the crusts lead to the conclusion that they have a hydrogenetic origin, precipitating directly from seawater. Although the content in Fe and Mn of the crusts is consistent with data available for the Atlantic, the mean concentration of Co is comparable to the average values for the Pacific. Cu and Ni show lower values than the ones known for the Pacific."

Sep 1, 2014

By S. J. Stokowski

Abstract An extensive drilling and laboratory testing program indicates that a construction aggregate resource is present within the Oligocene Sombrerito Formation limestone, southwestern Dominican Republic. The first part of the testing program included the collection, photographing and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I- (youngest) approximately 10 m of white, dense marine limestone II-approximately 5 m of white, interbedded dense and chalky marine limestone III-more than 2 m of tan, chalky, calcitic dolomite. Unit I is often altered by lateritic weathering and/or dolomitization. Unit II is often altered by dolomitization. The cores were individually crushed by quarry layer into coarse and fine aggregate sizes for chemical and physical analyses: specific gravity and absorption, MgSO4 soundness, sand equivalent, Atterberg limits of the minus #40 mesh fraction, and LA degradation. The unaltered portion of Unit I is suitable for all construction aggregate uses. Unit II is best suited for crushed stone base. Each of the non-weathered units decreases in coarse-aggregate yield and quality with depth and diagenetic dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average five-cycle MgSO4 soundness of about 17%.

Jan 1, 1991

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

By Raymond A. Bradbury

Martin County Coal Corporation's operations are located on Wolf Creek in Martin County in the eastern part of Kentucky. The mining complex was started in 1971 and has grown to a 2.273 Mt/a steam coal operation. All of the production goes to Duke Power Company's Belews Creek electric generating station in North Carolina. Production comes from four seams that are mined by deep and surface mining methods. Surface mining accounts for 55% of the production and the remainder comes from 2 underground mines. Continuous miners are used exclusively underground. The preparation plant was originally designed to take coal at the rate of 907 Mt/h but that has gradually been increased to 1134 Mt/h. Other cleaning equipment includes Daniels DMS vessels, Model 77 Deister tables, 355.4-mm R. & S. Hydro- cyclones, Krebs 254-m classifying cyclones, Daniels froth cells and in 1980, 3 Krebs 508-mm heavy media cyclones were added to recover some lost and misplaced material. CMI centrifugaldryers and a Hey1 & Patterson size 100 thermal dryer are also part of the coal preparation equipment.

Jan 1, 1981

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By John F. Oyler

The performance of high alumina refractory subjected to high compressive loads and high temperatures is an area in which operating experience is quite limited. This paper documents the results of five months of operation of a combustion chamber lined with 83 pct alumina brick subjected to compressive stresses as high as 45psi and hot face temperatures of about 2750°F. It also describes a method for predicting long term subsidence results based on the limited information available in standard hot load limit tests. Descriptions of the chamber itself and the pilot plant upon which its design was based are included.

Jan 1, 1978

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

By K. Huttu, A. van Wageningen

"The Kittila underground mine is extracting one of the largest known gold deposits in Europe and has an estimated mine life through 2034. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. The ore at the Kittila mine is refractory, making gold extraction relatively difficult because the gold is generally locked inside the two main sulphide minerals – arsenopyrite and arsenic-rich pyrite. The orebody consists of a complex pinch-and-swell structure including up to 100 different gold mineralization lenses. Fluctuating gold prices and other economic considerations increase the need to maintain and update the mining plans more frequently. Over 3,000 stopes need to be designed and optimized once a year for the LOM-plan and more frequent updates are needed for mid- and short term plans as well as production studies. As a large part of ore body is very sensitive to cost and gold price changes, stope optimization is crucial to find the best possible production scenario for every moment. Kittilä has gone through several methods for stope design and optimization. Most recently the Deswik Stope Optimizer (Deswik.SO) has been successfully used. Dewsik.SO has helped Kittilä to design and optimize stopes in a timely and cost efficient manner. Together with the Deswik suite of planning tools, reliable and auditable plans are created. This paper describes the methods used for stope design and optimization at Kittilä. THE KITTILÄ MINE The Kittila underground mine in northern Finland is extracting one of the largest known gold deposits in Europe. Kittila achieved commercial production on May 1, 2009, becoming Agnico Eagle’s first mine to open outside of Canada. The Kittilä orebodies were initially mined from two open pits – Suuri and Roura – and underground operations were added in October 2010. The pits were mined out in November 2012, so mining is now entirely underground in the Suuri and Roura deposits. Additional, small open pits will mine any remaining near-surface reserves in the future. The Kittila mine is located in the Lapland region of northern Finland, approximately 900 kilometres north of Helsinki and 150 kilometres north of the Arctic Circle. With a mine life estimated through 2034, Kittila is Agnico’s longest-life mine. The mine’s proven and probable reserves contain 4.7 million ounces (32 million tonnes at 4.6 g/t gold). Ore has been mined from underground since 2010. The original 3,000-tonne-per-day operation underwent an expansion project to increase the throughput capacity of the mill by 1,000 tonnes/day, starting by the end of 2014. The region around the Kittila mine is underlain by mafic volcanic and sedimentary rocks of the Kittila Greenstone Belt oriented nearly vertical. This greenstone belt is similar to those hosting Agnico Eagle's Canadian deposits in Quebec’s Abitibi region and Nunavut. At the contact point between iron-rich and magnesium-rich rocks lies a 100- to 200-metre-thick structural zone known as the “Suurikuusikko Trend”. This trend hosts the Kittila deposit, where multiple mineralized zones have been traced over a strike length of more than 25 kilometres."

Jan 1, 2015

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By J. F. Brune

This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Although direct examinations of the gob atmosphere are difficult due to the inaccessibility of these gobs, evidence from methane drainage practices and investigations of numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners. Most recently, this was demonstrated in the explosion of the Upper Big Branch Mine in West Virginia, where 29 miners lost their lives.The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions, along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Jan 1, 2013

By Graham Davey

High-speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However, it has been widely used in the industrial mineral field for more than 30 years. Many existing metallurgical operations are looking to maximize economic return from existing deposits this requires new thinking and technologies. The operating experience of two copper operations is discussed here to show the effect of the introduction of the Metso Stirred Media Detritor (SMD), a new type of high speed stirred mill. Both operations have derived significant metallurgical benefits from this new technology. The benefits and process difficulties are explained. The initial drive in high speed stirred milling technology was toward ultra fine grinding where the mill product has an 80 percent passing size of 15 µm (937mesh) or less. More recently, a number of installations have occurred in a more conventional regrind setting. Few conventional copper concentrators require such fine grinding to attain satisfactory copper grades and recoveries. So other advantages must be considered here rather than just the ability to grind fine with good power efficiency.

Jan 1, 2004

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994