Search Documents

By D. Nardini

The need to move towards faster and safer mine development is a key priority in mining houses globally. In addition to this, South Africa faces an array of challenges introduced by labour-intensive operations; hence a study was conducted to look into improving development rates and labour productivity, specifically in the areas where trackbound flat-end development is required. The aim of the study was to propose a method to deliver fit-for-purpose tracked tunnels that advanced at a rate of one blast per end every single working day. A major part of the study was to optimize the selection of an appropriate trackless fleet and mitigate any constraints introduced with the mechanization. This was done by creating scenarios, based on a typical case study, looking into the aspects around safety, mine design, mine activity cycling, men and machine requirements, service installations, and trackless-trackbound interfaces. The case study was based on a deep-level gold mine developing twin headings with connectings; however, with the move to extend and deepen platinum operations it is foreseen that twin end development will become more prevalent due to ventilation, logistical, and other requirements. With the introduction of the trackless mechanized system suggested, development rates of 56 m of system advance are expected (189 m total development), with on an average of three headings and fixed blast times. Scenarios run with multi-blast conditions yield expectations of 75 m/month advance of the system, significantly higher than the conventional performance seen today.

Jan 1, 2012

By A. F. Silva, R. Dockendorff, J. M. Girao Sotomayor, V. F. Navarro Torres, C. Castro

This paper shows the importance of performing probabilistic analyses in open pits, especially for mine planning, which can lead to more efficient ore extraction and meeting the acceptability criteria for safety in mine slopes. Three-dimensional stability analyses were performed to evaluate the future geometry of a large open pit for iron ore extraction in Brazil. The strength parameters of the lithologies were calibrated using ruptures in the pit walls. After determining the factors of safety (FoSs) from the calibrated parameters, probabilistic analyses were performed using the total range of values of each parameter under different field conditions to verify the reliability of the initial analysis. In this sense, it was possible to plot the probability of failure (PoF) and the FoS on the graph of slope height versus slope interramp angle (IRA) for the future pit in each lithology. IRA recommendations are made for two scenarios: (1) the best scenario: dry without ubiquitous joints and (2) the worst scenario: the water table at 10 m depth with ubiquitous joints in the most unfavourable direction. The results show that probabilistic evaluation is an important tool for establishing alert mechanisms in slopes that can be termed stable.

Jul 2, 2022

By R. Dehghan, M. Zarei, A. Tohry, S. C. Chelgani

Typical depressants for selective reverse flotation of iron oxides from complex silicates do not generally show high levels of efficiency. Therefore, as a hot topic, there are several ongoing investigations in this area. The main aim of this paper is exploring the potential of using humic acid (HA) as a depressant in reverse cationic flotation of hematite from complex silicates. For such a process, the wettability and flotation behaviour of pure minerals (hematite and silicates) was investigated at pH 10 in the presence of HA and cationic collector. Adsorption mechanism of HA on these minerals was measured by zeta-potential and FTIR. Results of flotation tests showed that at the lower concentrations of HA, selective separation of silicates from hematite is beneficial, where the floatability of amphibole was higher than pyroxene. A higher separation efficiency of hematite through reverse flotation was observed in the presence of amphibole, in comparison with the presence of pyroxene. Wettability studies showed that HA has a significant effect on reducing the hydrophobicity of treated minerals with the collector. The adsorption, ZPC and FTIR test results indicated that HA was adsorbed on both silicates and hematite. However, the absorption intensity onto hematite was much higher than silicates. It was found that the adsorption mechanism of HA on hematite takes place through both strong H-bonding and ligand exchange. Keywords: Reverse cationic flotation, humic acid, iron oxide, complex silicates, surface adsorption

Jan 1, 2020

By R. Kok, N. B. Strydom, P. L. Jooste, W. H. Van Der Walt

Intermittent exposures to heat, and the retention of heat acclimatization by N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow), R. KOK, M.Sc. (Potch.) (Visitor), P. L. jOOSTE, M.Sc. (Stell.) (Visitor), and W. H. VAN DER WALT, B.Sc. (Potch.) (Visitor) Twenty-one heat acclimatized subjects were assessed for the degree of acclimatization attained with respect to heart rate, rectal temperature, and sweat rate during a standard four-hour heat-stress test. Thereafter, they were put on light duties in cool environm ents for four weeks, except for four hours of exposure to heat every seventh day. Their state of heat acclimatization was again assessed two days after the final week's exposure. Although heart rates and body temperatures showed significant increases over the initial values, no differences were observed in sweat rates and, in general, the subjects were rated as still adequately acclimatized to heat.

Jan 7, 1975

By P. Michalcik, V. Petros, M. N. Bagde, K. Holub

The objective of this paper is to present some results of laboratory experiments during the investigation of stress-strain characteristics of Carboniferous sandstones at dynamic loading. During these experiments increasing frequency and the constant amplitude of dynamic loading and/or constant frequency at different amplitude of dynamic loading were applied. Der Gegenstand dieses Artikels ist, irgendeine von Ergebnissen von Laborexperimenten bei Messung der Spannungs- und Deformationscharakteristik der Karbonsandsteine bei ihrer dynamischen Belastung vorzustellen. Im Laufe diesen Experimenten wurden entweder anwachsende Frequenzen bei konstanter Amplitude der dynamischen Belastung, oder gleiche Frequenzen bei variabler Amplitude der dynamischen Belastung verwendet. L'objectif de ce papier est présenter quelques résultats d'expériences de laboratoire pendant l'enquête de caractéristiques de la tension – deformation de grès Carbonifère à sollicitation dynamique. Pendant ces expériences fréquence croissante et l'amplitude constante de sollicitation dynamique et/ou fréquence de la constante à amplitude différente de sollicitation dynamique ont été appliquées.

Jan 1, 2003

By L. A. Cornish, B. Eatwell

Austempered ductile iron (ADI) is a ductile iron which has had its matrix toughened by an austempering process. The alloy exhibits remarkable properties, which it owes to a unique microstructure comprising graphite nodules embedded in a matrix of acicular ferrite and carbon-enriched austenite. The properties include high strength combined with high toughness and ductility. Excellent wear resistance is also exhibited because, under strain, the austenite is transformed locally to martensite. Samples of ductile iron were austempered to produce grades I and IV AD!, and were tested at various strain rates. The grade IV ADI exhibited higher strengths and lower difficulties, and the strengths were found to be more dependent on strain rate. Transformation to martensite was more prevalent at the lower strain rates. A mechanism of increased flow stress and work hardening in the austenite of the matrix is proposed to explain the higher strength of the samples at high strain rates, where significantly less martensite is formed in the matrix.

Jan 1, 1995

Corosion technology: An information source book, by Judith Ann Douvile. Taylor & Francis, 1989. 188 pp. £32. Stainless steel buyers guide 1990. Southern Africa Stainless Steel Development Association (P.O. Box 4479, Rivonia, 2128), 1990. Free. Fatigue and stress of engineering materials and structures, edited by H.P. Lieurade. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur- Marne, France), 368 pp. US$ 109. Titanium and aluminium, edited by P.A. Coulon. ITT International (40 Promenade Marx-Dormoy, 93460 Gournay-sur-Marne, France), 200 pp. US$ 80. Engineering applications of stochastic processes. Theory, problems and solutions, by A. Zayezdny, D. Wulich, and D. Tabak. Chichester, John Wiley, 1989. 525 pp. £54.50. Metal behaviour and surface engineering, edited by S. Curioni, B. Waterhouse, and D. Kirk. ITT International (40 Promenade Marx-Dormoy, 93460 Gournaysur- Marne, France), 413 pp. US$ 109. Fuzzy control and fuzzy systems, by W. Pedrycz. Chichester, John Wiley, 1989. 272 pp. £37.50. CILO (carbon-in-leach with oxygen) cost study, by Minproc Engineers (USA). Free.

Jan 1, 1990

By A. Ball

This paper addresses the need for a unifying model that will permit the selection and design of optimum materials for a given wear situation. With this objective in view, the characteristics of the various forms of abrasive, adhesive, and erosive wear are described in terms of localized stress, strain, strain rate, and frictional heating. The measured performance of a variety of metallic, ceramic, and polymeric materials and coated or surface treated materials are described briefly. These results were obtained under conditions of dry-particle abrasion, abrasion in conjunction with corrosion, cavitation erosion in liquids, erosion by particles in low- and high-velocity gas streams, and erosion by particles in a liquid stream. Electron microscopy was used extensively, together with microhardness profiles, in the determination of the modes of material detachment and the underlying deformations and structural changes. As a result of the experimental work, a model based upon a critical strain to microfracture is presented. The microstructural features and materials properties that determine wear resistance are discussed.

Jan 1, 1986

By S. M. Spottiswoode

A simple method for the application of excess shear stress (ESS) analysis to the mining of planar reefs is examined. The potential for seismicity associated with mining is expressed as the calculated increase in ESS on a regular grid of points 50 m above the reef, and is compared with observed seismicity around a deep-level, relatively geologicaly-undisturbed gold mine. Thirty regions were studied, involving over 2000 seismic events with magnitudes greater than 1,5 on the Richter scale and associated with almost 2 million square metres of stoping. The total seismicity, measured either as the number of seismic events or as the total radiated energy, corelated more closely with changes in ESS than with ERR. The incidence of rockbursts also favoured the ESS model. Corelation coeficients of around 0,8 for seismicity and ESS indicated that the assumptions inherent in the method used are collectively reasonable. The total seismicity in each region was found not to be strongly controlled by the presence of dykes and faults, although numerous individual seismic events were located close to such features.

Jan 1, 1988

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By J. G. Ferguson, R. E. Burnton

The nature of the coal and of the roof in No. 3 seam at Coal brook Collieries is such as to preclude the use, during bord and pillar mining, of conventional mining equipment that employs cutting and blasting in its production cycle. Continuous mining machines of the borer type, operating within a mining height range of 1,9-2,3 m, have been successfully employed in No. 3 seam since 1957.The experience gained with this type of equipment, the operational methods adopted, and the results achieved are described. The ventilation method used to eliminate the dust and methane hazards created by this type of equipment is stressed. The limitation on the minimum mining height that can be obtained with the borers in use has lead to the recent introduction of a Rotary Drum type of continuous mining machine. This equipment is capable of operating in areas where the seam width decreases to 1,5m. The production potential of the machine has been proved. The roof conditions created by the cutting action of the Rotary Drum type of miner are not considered satisfactory and a modified drum head profile is to be tried.

By N. B. Strydom, H. H. E. Schroder, A. van der Linde

This paper describes a study of the destination of the mercury that is present in the ore during the recovery of gold. It was found that over 96 per cent of the mercury passed through the process untouched. A small amount finds its way into cyanide solution, and is concentrated with gold in Zinc dust as Merrill precipitate. When the precipitate is calcined, the mercury is driven off and finds its way into the atmosphere. However, dilution of the stack gas in the atmosphere appears to be sufficient to prevent hazardous concentrations arising at ground level. No other significant concentrations of mercury were found at any stage of the process. The amount of mercury lost to the atmosphere by this mechanism appears to be less than 200 kg per year throughout the gold-mining industry in South Africa. Virtually no mercury vapour could be detected in the air in the smelt-house. Slight increases in mercury concentrations above background level were observed in soils around the reduction plants and in the discharge or return waters, but no environmental stress is anticipated from these increases.

Jan 1, 1982

By U. C. Galimidi, J. M. Stewart, A. J. Van Rensburg

The effect of body movement on convective heat transfer from a man performing a block-stepping task was investigated experimentally by direct measurements of convective heat transfer. A series of experiments was conducted in which a nude man was required to stand at rest or to block step at 12 and 24 steps per minute. Wind speed, which was kept constant during each experiment, spanned the range 0,5 to 3,5 m/so Air temperature was kept constant at 43 °C in all the experiments. The results showed conclusively that the convective heat-transfer coefficient depends on the stepping rate. The effect of body motion can be regarded as being equivalent to an increase in the velocity of the free stream. The equivalent increase in air speed was found to be 0,36 and 0,77 m/s for 12 and 24 steps per minute respectively. Data from various sources, including the present study, indicate that wind speed should be increased by about 0,30,0,55, and 0,80 m/s to account for low, moderate, and vigorous body movements respectively. These findings are of direct relevance to the practical assessment of heat stress.

Jan 1, 1979

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

By M. Gholinejad

Applying non-explosive expansion material (NEEM) is one of the safest methods for rock fracturing, especially in a hard rock quarry. An experimental study was conducted to determine the pressure exerted by NEEM in a hole, which is necessary for analysing rock fracturing, particularly in a numerical modelling. Stress distribution was developed in a thick-wall cylinder in order to measure the tangential strain on the external boundary. In the experiments, nine pipes of different materials and varying diameters were selected and then loaded internally with a general type of NEEM. Through electrical strain gauges, the tangential strains were recorded on the external boundary of the pipes. The results obtained from these tests and existing data from previous researchers were utilized for the statistical analysis. A new experimentally-derived formula is proposed for determining the pressure exerted by NEEM by multiple parameter regression with a high correlation coefficient. The proposed model has a nonlinear form with three independent parameters i.e. the hole diameter, the time, and the modulus of elasticity of the material.

Jan 1, 2012

By R. E. Gürtunca, D. J. Adams

Writen contribution by J.F.Curtls The subject mater of the paper is interesting in that, instead of 'numerical modeling based on elastic theory' being used for the prediction of energy release rate (ERR) in relation to various types of stope support, including backfil, use is made of stresses in the backfil in an atempt to corect the numerical modeling. Authors' reply to J. F. Curtis We thank Mr Curtis for his contribution to our paper. First of al, it should be emphasized that the object of the paper is not to address the validity of ERR as a tool for the assessment of seismic events or rockbursts, but to determine an in situ modulus for the rockmass with the aid of backfil measurements. Writen contribution by T.R. Stacey Although the authors of the above-mentioned paper have presented some good and interesting information, the title of the paper, and the recommendation that such an in situ modulis should be used for calculations of energy release rate (ERR), are viewed with some concern. The reasons for this concern are as follows. Authors' reply to T.R. Stacey Dr Stacey's comments on our paper are appreciated; we should like to address his concerns as follows.

Jan 1, 1991

By C. C. Johnson

In the fourteen years that Rössing Uranium Limited has been in production, the metallurgical operations and controls on the leaching plant have evolved through four basic stages. Initially, the emphasis was placed on the achievement of consistent plant operation by overcoming severe startup difficulties. The second stage involved the attainment of the design operating targets, and also the commissioning of the ferric-leaching reactors in order to achieve a ferric ion concentration of more than 3,0 g/l. Improvements in control then became the priority, with the emphasis on consistently achieving the target concentrations of ferric ions, total iron, and terminal acidity. The latest phase has concentrated on the optimization of costs by means of adjustments to the historically established operating parameters in order to achieve large savings on consumables while maintaining the leaching efficiencies. Apart from the obvious incentive of reducing costs in an inflationary economy and a depressed uranium market, impetus for this work was given by a change in the type of ore from the open pit, which has the effect of reducing the extraction efficiency while increasing the consumption of consumable materials. These problems and their solutions are discussed in detail, and the importance to cost-effective optimization of an accurate, up-to-date cost-reporting structure is stressed.

Jan 1, 1990

By A. P. I. Popoola

Aluminium AA1200 was laser alloyed with a combination of nickel and titanium diboride using different weight ratios. Chemical reactions took place with the formation of different phases. The characterization of the alloyed surfaces was carried out by x-ray diffraction (XRD), optical and scanning electron microscopes. The alloyed surfaces are composed of the initial phase of Al-Ni dendrites and eutectics of TiB2/Al and TiB2/Ni distributed on the initial phase. Experimental results obtained showed that Al-Ni intermetallics brought about a significant increase in the hardness property of Al; however, these intermetallics are highly brittle and prone to fail by brittle fracture or stress corrosion cracking when put in service. The addition of TiB2 brought about a reduction in the formation of the seintermetallic phases. A microhardness increase of over 10 times the hardness of the substrate was achieved. Keywords Dendrites, intermetallics, metal composite, Nd: YAG laser.

Jan 1, 2011

The mining rock-mass rating (MAMA) classification system was introduced in 1974 as a development of the CSIA geomechanics classification system to cater for diverse mining situations. The fundamental difference was the recognition that in situ rock-mass ratings (AMA) had to be adjusted according to the mining environment so that the final ratings (MAMA) could be used for mine design. The adjustment parameters are weathering, mining-induced stresses, joint orientation, and blasting effects. It is also possible to use the ratings (AMA) in the determination of empirical rock-mass strength (AMS) and then in the application of the adjustments to arrive at a design rock-mass strength (DAMS). This classification system is versatile, and the rock-mass rating (AMA), the mining rock-mass rating (MAMA), and the design rock-mass strength (DAMS) provide good guidelines for the purposes of mine design. However, in some cases a more detailed investigation may be required, in which case greater attention is paid to specific parameters of the system. Narrow and weak geological features that are continuous within and beyond the stope or pillar must be identified and rated separately. The paper describes the procedure required to arrive at the ratings, and presents practical examples of the application of the system to mine design.

Jan 1, 1990