Search Documents

By Albert L. Toenges

The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by: (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war material; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this Critical fuel situation, an investigation was made of possible sources of fuel nearer to points of consumption in New England.

Jan 1, 1948

By G. E. McElroy

This report discusses the construction and use of an all-pressure psychrometric chart in which the requirements of simplicity of appearance and absolute accuracy have been waived, to a certain extent, to provide for the rapid determination of psychrometric data and for the rapid solution of air-conditioning problems of major interest to the mining industry. Many mines in which air-conditioning problems are important are situated at elevations far above sea level and embrace great differences in elevation - in excess of 8,000 feet in certain mines - throughout their airflow circuits. Under these conditions, the effects of variations in the pressure of the atmosphere upon the physical properties of the mixture of air and water vapor of which it is composed are considerable and should be taken into account in the solution of problems. The simple types of psychrometric charts in common use, such as the Carrier, Bulkeley, Hill, and Goff (American Society of Heating and Ventilating Engineers Guide), are not generally suitable, in that they are drawn for a single barometric pressure - 29.92 inches mercury.

Dec 1, 1947

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

In this U.S. Bureau of Mines report, in situ vat leach mineral recovery system concepts are described and cost compared with conventional mining and pad and autoclave leach processing systems. In the proposed systems, leachable ores are enclosed in place in reagent-impermeable in situ vat constructions. The ores are then rubbled and flood leached or flood oxidized and leached. The in situ vats are called stope leach or stope autoclave vessels. The report also proposes ore body-adjacent in situ vat constructions containing rechargeable processing stopes. A series of ore body-specific, innovative, and conventional mineral recovery systems case study designs are described and prefeasibility level costed. Based on a comparison of these prefeasibility level cost estimates, the proposed systems are determined to be economically competitive with conventional min¬eral recovery systems. The in situ vat leach mineral recovery systems concepts for leachable and refractory ores are developed around the drill-split narrow-vein and longwall mining methods described in part 1 of this Information Circular series.

Jan 1, 1995

By Michael J. Brnich

During the past 15 years the number of reportable mine fires has declined. A decline in the number of reportable fires is a gross indicator that allows experts to say something about the underground coal industry generally: There has been some improvement in overall mine fire preparedness. However, such an indicator is less reliable as a predictor of readiness at any particular operation. An indication of fire fighting preparedness would have to be assessed from evidence gathered at the mine site. In other words, there are two levels from which to view the problem. On a general level, there has been significant improvement in the industry's fire response capabilities over the past two decades. Specifically, however, little data has been gathered on a site-by-site basis to determine what improvements might be made on a local level. These improvements would move beyond regulatory compliance. It is expected that this manuscript, based on work conducted at an underground coal mine in the western United States, will help to focus attention on some central concerns involving this critical issue.

Jan 1, 2006

By W. F. Marshall

This Bureau of Mines report discusses tests conducted with four different catalytic reactor designs to determine the influences of exhaust treatment systems on emissions from diesel engines. Although there was significant differences in oxidation efficiencies at light to intermediate engine loads, all four catalysts were very effective in reducing emissions at heavy loads. Compositional determinations included carbon monoxide, carbon dioxide, unburned hydrocarbons, oxides of nitrogen, aldehydes, sulfur dioxide, sulfates, and particulate loading. Particulate size, exhaust odor intensity, and the character of the unburned hydrocarbon component were also determined.

Jan 1, 1978

By M. M. Fine

The results of tests on oxidized lead ores from two properties are reported in this paper. The investigation was on a small laboratory scale only; no pilot-plant tests were made. One sample, from the Magajupa Mining Co., near Duenweg, No., contained coarsely crystalline and disseminated galena and cerussite, so both tabling and flotation were considered in the beneficiation. By this treatment of an ore containing 11.5 percent lead, a recovery of 79.5 percent of the lead was made in a concentrate containing 73.3 percent lead.

Jan 1, 1948

By D. S. Burgess

A commercially available Halon 1301 extinguisher has been evaluated as part of an explosion-suppression system for use in coal mines. Studies were made both of the dispersion pattern of the Halon 1301 at an initial pressure of 280 psig, and of the efficacy of this suppressant against 9.5 percent methane-air flames. These flames were quenched successfully only when the suppressant was applied before the fireball diameter exceeded 18 inches.

Jan 1, 1971

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By James Spiers

This paper describing the mining practice at the Central-Eureka mine is one of a series of similar papers being prepared by the United Staten Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described in this paper are illustrative of the methods employed in the exploitation of comparatively low-grade gold ores under the extremely heavy and swelling ground conditions which occur in the Mother Lode belt of California. The Central-Eureka Mining Co. comprises a group of adjoining mines in Amador County near Sutter Creek. The principal mines of the consolidated group are the Central-Eureka, formerly known as the Summit mine, and the Old Eureka mine, which is also known as the Hayward Quartz mine. The group is situated in the most productive part of tae main Mother Lode belt, the 10-mile portion which lies between the towns of Plymouth and Jackson. The three largest producing mines of the entire belt at the present time are the Argonaut, Kennedy, and the Central-Eureka; these lie within a radius of less than 1-1/2 miles.

Jan 1, 1931

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

By Alexander May

This report describes a new method of weighing based upon observing the apparent weight of an object ill two separate pure gases. The method is presented in terms of experimental data which prove its soundness, but does not attempt to show the maximum accuracy possible with this technique. The new method incorporates the underlying principle that the apparent weight of an object is a linear function of the density of the atmosphere in which the object is weighed. The coefficients of this linear function are the true mass and volume of the object. From this functional relationship the true mass and volume of the object may be determined.

Jan 1, 1970

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By D. Harrington, W. J. Fene

That fatalities from mine explosions can be very much reduced from the experience of past years if not wholly eliminated was fairly well demonstrated during the fiscal year ended June 30 , 1934 , there being only 28 deaths in the United States from explosions during this period . This is by far the lowest number of fatalities from explosions in the history of coal mining in the United States insofar as records are available . Although the frequency of occurrence of explosions has not decreased greatly during the past 6 years , there has been a marked decrease in severity , indicating that our coal -mining people are taking more effective precautions to prevent the spread of explosions . Pennsylvania is a good example of what may be done in reducing both the frequency and the severity of explosions ; by the adoption of up- to - date safety measures , Pennsylvania bituminous mines now have the enviable record of only one major explosion disaster in more than 5 years , and the one major explosion which did occur cost but 7 lives although 277 persons were exposed ; their lives were saved because rock- dusting prevented the spread of the flame and violence . Many of our other mining States are making definite progress in working mines without disastrous explosions and fires ; some of these , like Alabama , West Virginia , Indiana , Wyoming, and others now operating with few , if any , explosions , have had anything but a favorable record in the past .

Jan 1, 1935

By Charles W. Huggins

Knoop hardness indentations were studied and measured with the electron microscope on TiB2, HfC, and A1B12 crystals. A detailed description of replicating the indentations using collodion and Faxfilm is made. A John Hopkins grating having 28,800 lines per inch was used to accurately determine the magnification used on the electron microscope. The primary objectives were to prepare carbon replicas of hardness indentations, to measure the indenations accurately, and to compare the results with those obtained with the light microscope. The resulting data showed excellent agreement between the measurements made on the replicas with the electron microscope and those made with the optical microscope. The replicas made from collodion showed slightly better agreement with the light optical values than did the replicas made from Faxfilm.

Jan 1, 1963

By M. J. Ferrante

Enthalpy and entropy increments above 298.15° K were determined for cop-per sulfate between 298° and 1,000° K and for copper oxysulfate between 2980 and 1,146° K by the method of copper-block drop calorimetry. Enthalpies, entropies, and heat capacities are tabulated for both compounds. In addition, free-energy functions are tabulated for the sulfate. Equations representing the enthalpies are given for each compound.

Jan 1, 1972

In 2005, a total of 263 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining commodity sector, comprising 1.8% of all mining operations. ? Gold mines comprised 46.0% (n=121) of all metal mining operations. Other common types of metal mines were iron ore (n=32; 12.2%), copper ore (n=31; 11.8%), and lead and/or zinc ore (n=16; 6.1%). ? Nevada had the largest number of metal mines (n=52; 19.8%), followed by Alaska (n=27; 10.3%).

Jan 1, 2008

By Earl T. Hayes

For several years the Northwest Electrodevelopment Laboratory of the Bureau of Mines, in cooperation with the Air Materiel Command, U. S. Air Force, has been studying zirconium alloys. A preliminary survey of these alloys has been completed and reported as a Bureau of Mines Report of Investigations. 4/ Originally the purpose was to determine the suitability of zirconium alloys in medium-temperature applications. However, data also were obtained on other properties of these alloys, and later the scope was broadened to include amore detailed investigation of a selected group. The zirconium-titanium system was one of those chosen. The Bureau of Mines has been instrumental in the commercial development of both of these metals and has constructed pilot plants for the production of titanium at Boulder City, Nev., and for zirconium at Albany, Oreg. Both elements are in subgroup A, fourth series of the periodic table, and therefore have many properties in common. Since both have similar atomic structures and lattice dimensions the possibility of extended mutual solubility seemed likely. Inc transition-point diagram of Fast indicated that the two metals are completely miscible in all proportions in both the alpha and beta forms.

Jan 1, 1951

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990