Search Documents

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960

By W. F. Marshall

This report describes exhaust-emission data from 10 diesel engines: six 4-cycle, direct-injection, naturally aspirated engines; two 4-cycle, direct-injection, turbocharged engines; one 4-cycle, precombustion-chamber, turbo-charged engine; and one 2-cycle, direct-injection engine. These engines were tested over a 3-year period (1968-70). Lowest emissions were obtained with a precombustion-chamber engine. Emissions from the 2-cycle, direct-injection engine fell within the range of emission rates for the 4-cycle, naturally aspirated, direct-injection engines. Excluding the precombustion-chamber engine and excepting one of the 4-cycle, naturally aspirated engines, carbon monoxide emission rates were about the same for all engines tested. Test data on smoke, odor, and emissions of hydrocarbons, oxides of nitro-gen, carbon monoxide, and aldehydes are given.

Jan 1, 1971

By David R. Peterson

This report presents a deep ocean mining operational simulation which is capable of describing the response of the bottom collection unit to specified mining ship maneuvers and the corresponding operation of the mining ship maneuvering system. Bathymetry, obstacles, collector and pipe dynamics and ship maneuvering capabilities are included in the simulation. The simulation is capable of evaluating the technical requirements and operating costs for specified mine plans, Results are useful in assessing mine size requirements and provide operating 'cost 'estimates useful as inputs to deep ocean mining economic feasibility assessments, The simulation is used to determine the consequences of obstacles to mining system operations in terms of impact on mine size requirements and reduced production arising from obstacle avoidance maneuvers of a towed (unsteered) collector.

Jan 1, 1979

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By C. T. Baroch

The purpose of this report is to describe the design features and techniques used in operating a plant capable of producing about 1,500 pounds of titanium metal per day. The process used was based on the reduction of titanium tetrachloride with magnesium, a modification of what is generally known and spoken of as the Kroll process. Sponge metal crushed to melter's specifications was the end product of the operation as conducted. The report is divided into sections covering general plant layout and the major unit operations. These, in turn, are each divided into discussions of the equipment, operating procedures, and typical results. Descriptions are given in more detail than is generally expected of a technical report. During 1953 and 1954 over 130 engineers and businessmen, officially representing some 80 industrial, chemical, end engineering firms, visited the operating plant, and their questions, which indicated a serious interest in details, have served as a guide for the material contained in this report.

Jan 1, 1955

By R. J. Leary

A small electronic digital computer employing punched cards has been used to facilitate the solution of a variety of problems in Bureau of Mines pyrometallurgical research. In this work the computer has been found to be economical for solving both simple problems that occur repeatedly and those involving complex or iterative calculations. Each of these classes of problems and their respective solutions are described. These small computers can be used effectively by researchers when they work in consultation with a computer specialist. Close team work produces the required solutions in less time, and, oftentimes, in a more useful form. Participation in programming by researchers develops in them a skill for evaluating the suitability of problems for electronic computing.

Jan 1, 1960

By R. W. Michelson

The Bureau of Mines developed computerized mathematical models to estimate the economic availability of Mesabi Range taconite concentrates; these are a quality model, a cost model, and an economic availability model. The quality model evaluates metallurgical test data; the cost model determines iron unit cost from mining and processing cost data; and the economic availability model determines quantity from geologic and ore quality data. By correlating all of the physical resource quality factors and dimensional characteristics with the economic cost factors associated with producing iron ore pellets, these three models combine to establish a final relation between iron ore reserve quantities and iron unit cost.

Jan 1, 1970

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines, the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1957

By W. M. Myers

[The principle of the application of electrolytes for deflocculation of fine materials in order that impurities may settle out, and the subsequent flocculation of the suspended particles by a different reagent, is well known and has been applied successfully to clays. Flocculation is also applied with success to ore slimes. Thus certain electrolytes, particularly alkalies added to a suspension of colloidal particles cause deflocculation so that, suspension may be-maintained indefinitely. The addition of bother electrolytes particularly acids, on the contrary produce's flocculation and the articles produce's are rapidly precipitated from suspension leaving a clear liquid above: the precipitated mass. Salts of trivalent elements such as aluminum act similarly. Due to its cheapness the double sulphate of aluminum and potassium, ordinary alum, has been used extensively for treating clays. These properties of electrolytes. and. their utilization in the commercial: preparation of clays have been described in publications of the Bureau of Mines.2]

Jan 1, 1927

By Warren E. Morrison

A simplified energy model for the United States is quantified for a recent historical period. The basic model and calculated quantified structures are used for a number of analytical case studies that estimate midterm and long-range shifts in patterns of energy resources demand and required supply. Historical data series are presented for the years 1947 to 1965 in the form of integrated energy balances by source, form, and consuming sector. In case studies I to XII, conditional projections of historical trends of energy demand and required supply are made for the midterm period 1966 to 1980. The projections are carried out by correlation of major energy components with relevant independent variables such as major economic indicators. Simulations of the medium-range projections to 1980 are carried out by varying the assumptions for the determining variables to produce high-and low-range projections for the midterm period. Case studies XIII to XXII are long term contingency or technological forecasts to the year 2000. These cases assume technological changes or innovations that produce major shifts in the long term pattern of energy consumption and the mix of required resources. The domestic resource base is assessed in its ability to meet projected or forecast demand for energy resources under the midterm and longrun assumptions made in the various case studies. Various energy issues or problems identified from the analyses of the case studies are discussed, and possible alternative approaches to solutions to these issues or problems are suggested.

Jan 1, 1968

By J. B. Zadra

After the discovery of the rare-earth mineral deposit in the Clark Mountain area near Mountain Pass, San Bernardino County, Calif., two samples wore obtained through the Mining Division of the Bureau of Mines for investigation of possible method of concentration. Three other samples were received later from different locations in the same area. The rare-earth mineral in this ore had been identified by E. T. Schonk as bastnaesite, a fluocarbonate of the rare-earth metals containing cerium, lanthanum, praseodymium, thorium, uranium, etc. Associated with the bastnaesite were barite, silica, and some calcite. The bastnaesite contained a small amount of iron as a coloration and some manganese. Twenty to fifty percent of the weight of the samples studied was bastnaesite, or ten to twenty-five percent total rare-earth oxides; about half was cerium oxide. Apparently, none of this mineral occurred in pure form. Even the highest-grade particles 'wore contaminated by fine, interlocked grains of barite, calcite, and silica; barite contamination predominated, and the barite was interlocked with varying amounts of bastnaesite. While the specific gravities of pure bastnaesite and barite (approximately 5.0 and 4.50 respectively) differ enough to allow separation by gravity, the interlocking of the minerals nullified this difference. Consequently, only a partial separation could be made by gravity concentration. The extremely fine grained texture of most of the ore prevented grinding to a size that would make concentration by flotation practicable; a partial separation of barite by this means was effected.

Jan 1, 1952

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By L. G. Marshall

This report presents a cross section of the sand and gravel operations in the Minneapolis-St. Paul area. The study covers individual operations, economic problems peculiar to the industry, glacial geology of the area and its effect upon the grades and types of products, and past, present, and future trends of the expanding population and its effect upon the industry.

Jan 1, 1963

By D. Bienstock, R. C. Kurtzrock, E. R. Bauer, J. H. Field

To remove hydrocarbons and carbon monoxide in automotive exhaust by oxidation , a catalyst of 4.2 percent Uз Og , 1.7 percent Cr₂ 0 , and 1.7 percent CuO supported on 1 /8 - inch y- alumina spheres was tested in a reactor in place of the muffler of a 1 / 2 - ton truck . Tests were made with both nonleaded and leaded gasolines . With the engine at operating temperature , tests were made with the engine idling and with the vehicle cruising at 30 mph . Auxiliary air was added to maintain an oxygen concentration of 3 to 4 percent in the gas leaving the catalytic reactor . The vehicle was operated for 83 hours (about 60 percent of the time with the engine idling ) and 525 miles with nonleaded gasoline . Conversions of 98 percent of the hydrocarbons and 100 percent of the carbon monoxide were achieved with the engine idling and with 7,000 ppm carbon atoms and 4- percent carbon monoxide in the feed to the reactor . Hydrocarbon conversions of 75 percent were obtained at cruising speeds of 30 mph with a feed of 1,700 ppm carbon atoms ; the carbon monoxide concentration was less than 0.3 percent in the feed and was unchanged in passage through the reactor . Identical activity was obtained initially in switching to a gasoline containing 1.9 ml tetraethyl lead (TEL) per gallon . However, there was a gradual loss in activity thereafter . Conversions in tests with the engine idling about 50 percent of the time , had decreased by 23 percent for the hydrocarbons and by 25 percent for the carbon monoxide from their initial values after 122 hours and 1,300 miles of operation with leaded gasoline . The levels of radioactive materials in the exhaust of the reactor and the radiation in the vehicle were negligible .

Jan 1, 1963

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and, (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke. This is the third of a series of reports giving results of studies by counties under part (1) of the investigation. This report covers Pike County, Ky., which comprises parts of the Harold, Williamson, Matewan, Gilbert, Pikeville, Regina, Hurley, Pound, and Clintwood quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By J. A. Organiscak

Quartz dust is one of the most significant ongoing health concerns in coal mining today. Since the early 1980's, the U.S. Bureau of Mines has conducted numerous studies in underground and surface coal mines to identify the sources of quartz dust and its fundamental characteristics. This report presents data and conclusions obtained from these studies. The two most significant quartz dust sources were found to be the continuous miner excavating rock and the highwall drill operating in a rock overburden. The percentage of quartz was found to be higher in the smaller size fractions of dust when significant amounts of rock were mined by the continuous miner. Another factor theorized to affect quartz dust generation and size characteristics is the morphology of the quartz-bearing rock. Several laboratory studies were conducted to investigate capture efficiency of water spray technology and flooded-bed scrubbers with respect to the particle size of the dust. Water sprays and flooded-bed scrubbers were both found to be less efficient on smaller dust particles, and the scrubber was particularly less efficient on quartz dust. These results indicate that quartz control technology should be directed at controlling smaller sized dust particles.

Jan 1, 1990

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

By Lewis A. Smith

This circular presents a summary of the domestic chromium industry, and discusses the salient features of the world situation , reflecting the literature of the subject . The United States Bureau of Mines has in its files additional detailed information on many subjects briefly discussed in this paper and desires to assist the industries and the public by giving further data in response to individual inquiries . It will welcome comment and criticism and any contributions that would assist in making future editions of this circular more accurate . Unlike most common metals , chromium is rarely marketed as a pure metal . The chromium industry deals mainly with chromite , the principal ore of chromium , and with ferrochromium , the basic alloy in which chromium enters the metallurgical industry.

Apr 1, 1932