Search Documents

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company's Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network. and 2)development at a set pit digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the models and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated fur their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

By Michael S. Contratto, Dave Marshall, Tom Brodersen

The European Union (EU) completed a new directive 2002/44/EC1 called the Physical Agents Directive (PAD) that establishes action and limit values for hand-arm and whole body vibrations. The directive specifies that: “…workers shall not be exposed above the exposure ‘limit value’.” 1 and “…once the exposure action values … are exceeded, the employer shall establish and implement a programme of technical and/or organisational measures intended to reduce to a minimum exposure to mechanical vibration and the attendant risks…” 1 The PAD limit value is effective for new machines starting July 6, 2007 and for used machines by at least July 6, 2010. These requirements apply to the users of machines, but machine manufacturers will be challenged to provide machines and information to help the users comply with the directive. Caterpillar manufactures machines with the goal of enabling our customers to comply with all regulations dealing with health and safety. Caterpillar designs all of our machines to provide a safe, comfortable and productive work environment. This study was to determine if seat suspensions could provide a reduction in the vibration environment experienced by operators of Caterpillar mid sized (<50,000KG) Track Type Tractors Methods Seat manufacturers were asked to provide seat suspensions that provide improved isolation over and above current seat suspension. Each supplier was provided with ride profiles and was asked to demonstrate the vibration reduction on a shaker table. Two suppliers provided suspensions that were compared with the current seat suspension in a field study. Three full factorial experiments were conducted. The first experiment was to evaluate overall suspension performance for four operations. The second experiment was to determine the benefit of the adjustable vertical damper at three different levels and the third experiment was to determine the effect of the fore/aft and side/side isolators. Six operators were used for the study. Acceleration was measured at the seat base and at the operator seat pad. Both the transfer function and the ISO 2631 RMS ride values were used to determine the seat suspension’s effectiveness of isolating the operator from vibration. A structured questionnaire was used to determine the operators’ subjective assessment of the seat suspensions. Results There was significant operator-to-operator variability in the vertical direction (>35%), however there was little variability in the fore/aft and side/side direction based on seat base

Jan 6, 2006

By R. L. Brown

This report is the 18th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations. The previous 17 reports have covered fiscal years, but this report covers not only the fiscal year from July 1, 1952, to June 30, 1953, but also July through December 1953, to bring the report to a calendar-year basis. Most of the material in this report relates to publications issued during the reporting period, Some work is mentioned briefly on which publications have not yet been issued or on which data are riot expected to be published, for security or other reasons, and in a few instances publications issues before the reporting period but not included in the previous report are mentioned.3/ Further details on the published work described herein may be found by referring to the publications cited in the footnotes. During the reporting period, the Bureau directed its research and technologic work on coal toward developing end encouraging increased conservation and more efficient use of our mineral fuel resources through more efficient and safer mining methods and improved methods of preparing and utilizing these fuels. Some significant advances, particularly in coal-mine safety, mining methods, and development and utilization of low-rank coma have been made.

Jan 1, 1954

By John A. Kost

Previous work performed under Contract H0220003 suggested that the mean incombustible content could be obtained with fewer samples and smaller samples without greatly increasing the sampling error. Under Modification No. 4 additional surveys were made in twelve coal mines, representing six states. Same 2,500 samples were collected, analyzed for incombustible content, and statistically evaluated. The earlier findings were substantiated.

Jan 1, 1975

By Ray J. Holmquist

"INTRODUCTION At the request of Elmer Burch, of Taos, N. Mex., the Apache mica mine was examined by an engineer of the Bureau of Mines in October 1942. As the result of this examination, the Bureau of Mines proposed to extend an adit to the projection of the mica-bearing dike. The Federal Geological Survey then prepared a topographic and geologic map of the property. This information and consultations with members of the Survey 3/ assisted in determining the course and extent of the exploratory work. The author supervised the work, which was done from January to May 1944.Title to the property was in litigation during the period of the Bureau of Mines investigation. Conrad Johnson, of La Madera, N. Mex., was contesting the valley of Burch's claim location covering the Apache mine. Johnson was a prior claimant. A map made during mining operations prior to 1929, showing all mine workings, was in the possession of Johnson, but he would not produce it for inspection as long as his title to the property was in doubt. The course of the adit extension was therefore controlled by the best information and judgment otherwise obtainable."

Mar 1, 1947

By A. A. Campoli

Retreat pillar mining concentrates stresses on workings directly outby gob areas, which can result in coal mine bumps. The development of bump-control design criteria by the U.S. Bureau of Mines was furthered by data from a novel bump control mining method at the Olga Mine, McDowell County, WY. The pillar splitting, retreat mining system induced large pillar pressure increases and roof-to-floor con-vergence. Roof-to-floor convergence monitoring proved to be a valuable tool in evaluating the pillar splitting mining method and localized destressing techniques. Maximum strain energy storage in chain pillars appears to have occurred just prior to the first of four split cuts. At that point a 15-ft-wide, highly fractured perimeter confined the core of the 55-by 70-ft pillars, permitting the pillar core to support tremendous pressures. Splitting the chain pillars into two 17.5-by 70-ft wings removed the confinement load, resulting in pillar yield. Thus, the pillar splitting mining method successfully redistributed the weight of the roof away from the pillar line. Shot fire and auger drilling destressing techniques aug-mented the pillar splitting mining method by redistributing the weight of the roof.

Jan 1, 1989

By Janine Pierce, Robert Larson, Christine Raasch

The vibration and impact environment for crew members on locomotives has been investigated in a series of studies conducted by Exponent Failure Analysis Associates (Exponent) beginning in 1990. Locomotive cab vibration and impact levels were measured on a variety of locomotive models operating over many different track sections across the Union Pacific, Burlington Northern Santa Fe, CSX, Norfolk Southern, and CONRAIL systems. The comfort and health implications of exposure to the measured locomotive vibration levels were evaluated by comparison with the human vibration exposure boundaries given in the International Standards Organization (ISO) standard 2631-1:1997, the British Standard 6841:1987, European Union (EU) Directive 2002/44/EC, measurements made by Exponent on various commercial and recreational vehicles, and vibration exposure measurement data found in the literature. Methods Initially, vibration levels experienced by locomotive crews were measured and recorded at incremental speeds covering the range of normal train operation. In 2003, a method of measuring the vibration exposure continuously by means of a digital recorder was developed, allowing the vibration level over the entire run or crew shift to be analyzed. For each seating location measured, acceleration was recorded on the seat surface beneath the ischial tuberosities (pelvis) of the seated crew member and on the cab floor directly under the seat. At each of the locations, triaxial accelerometers were used to measure the vibration along the longitudinal, lateral, and vertical axes. Since the vibration environment varies throughout the route, and locomotive vibration levels have been found to be primarily speed dependent, a speed sensor was used to continuously measure the speed of the train. To evaluate the recorded vibrations levels, the data was divided into two-minute segments, which were each processed per the 1997 ISO standard for weighted RMS vibration levels and Vibration Dose Values (VDV). Additionally, PSDs and 1/3 Octave RMS values were calculated to determine the frequency content of the vibration. For each two-minute segment, the average speed of the locomotive was calculated to allow for correlation with the recorded vibration exposure values. The resulting exposure values for the entire run were calculated by combining the data from all of the two-minute segments. Since introducing the continuous method of recording acceleration, 23 seating locations have been recorded on 11 locomotives traveling 11 different routes across various parts of the United States. One of the routes was a shift of ‘yard work’, traveling back and forth in a rail yard coupling train cars together. Results A guide to interpreting weighted acceleration values with respect to health is given in Annex B of the 1997 ISO standard. A health guidance caution zone is defined to indicate the

Jan 6, 2006

By S. J. Gasior

Pilot plant studies showed the technical feasibility of fluidized-bed operation for producing hydrogen and synthesis gas by the steam-iron process. A mixture of iron and iron oxide from 20-to 100-mesh was partially reduced with a simulated producer gas and then oxidized with steam and/or carbon dioxide. Results of tests show the effects of pressure, temperature, bed height, gas-to-solids ratio, type of iron oxide, and composition of gas on the gas and solids conversions during reduction and oxidation. A baffled free-fall solids system was also found operable. The short residence time of about 5 seconds limited conversion of the solids.

Jan 1, 1961

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By Bernard Lewis

The ignition problem: for a layer of firedamp bordering on a cloud of detonation products is evidently considerably more complicated than in the usual laboratory ignition experiments, in which a well-defined volume of gas is heated and the occurrence of ignition is observed after an induction period. An atmosphere of firedamp exposed to the detonation of a high explosive is subjected to heating by shock-wave compression and thermal conduction and to intermixing at the interface of the firedamp atmosphere and the cloud of deto¬nation products. Although a reliable physical-chemical analysis of the problem is not yet possible, one may nevertheless form a general view of the role of compression waves and the processes of heat transfer and diffusion at the interface. Near the mouth of a shot hole, or near a freely suspended cartridge, the firedamp atmosphere attains very high temperatures by adiabatic compression, and it is certain that such temperatures are sufficient to initiate chemical reaction. The pressure wave pattern is reproducible from one test charge to another if the initial experimental conditions are held constant; on the other hand, experiments on firedamp ignition do not yield a reproducible threshold condition for ignition, but only an ignition probability. Thus, the induction periods are sufficiently long that there is time for the compressed&apos;, heated gas layers to undergo random changes that may quench or promote ignition. Therefore, the analysis of the ignition problem hinges primarily on the discovery of the random events that modify the chemical reaction in the activated gas layers.

Jan 1, 1948

The overall objective of this study is to gather operational data from selected surface coal mining systems in the United States, and to assess the potential production and economic capacity of the systems. The study includes: four mines, each using a different mining technique and different equipment. One mine was selected from each of the major coal fields: Midwestern, eastern,, northwestern, and southwestern. The Midwestern Mine is located in the Central Plains and produced 1.45 million tons of raw coal during the study year The Midwestern Mine uses the area mining or box-cut technique. A large in-pit shovel and a bucket wheel excavator are used to remove the overburden. Coal is removed by a loading shovel and transported to the dumping point by large off--highway trucks.

Jan 1, 1975

By William E. Eckard

Production of oil from a narrow shoestring sand presents problems unique in the oil industry. Especially important, from both an engineering end an economic standpoint, are the limitations imposed upon well patterns and spacings by the shape of the field. This report concerns a study of the Paola shoestring, Miami and Franklin Counties, Kane., where well density of 0.85 acre per well was not uncommon to insure profitable primary recovery in a reasonable time. However, such a great number of wells increased the operator&apos;s investment and reduced his profit considerably. It was the purpose of this study to investigate various well patterns and spacings applicable to water-flooding a shoestring reservoir and the effect of these factors upon recovery of oil and the most profitable operation of the pool. The designer of well patterns for a shoestring sand should evaluate carefully the edges of the shoestring, even though they may be considered too thin to drill. These comparatively thin edges contain large quantities of recoverable oil; moreover they are resaturated with oil as the pool is water-flooded.

Jan 1, 1951

By G. E. McElroy

This paper3/ is one of a limited series being prepared by the Bureau of Mines to supplement a more extensive series on mining and preparation methods in the various mining districts of the United States. It describes ventilation methods and practices at the anthracite collieries in the Northern field of the anthracite measures of Pennsylvania as obtained by personal inspections in twenty of the larger collieries during 1933 and 1934 and from supplementary information furnished then and later by operating officials. This field is one of the four major divisions - Northern, Eastern Middle, Western Middle, and Southern - into which the anthracite deposits of Pennsylvania are naturally divided, and constitutes, in plan, a slightly bowed lens, about 60 miles long, and that extends from Forest City on the north through Scranton, Pittston, Wilkes-Barre, and Nanticoke to Shickshinny on the south with a. maximum width of 6 miles. It is the oldest and largest producing field of the four, and has produced continuously from 1S09. The total anthracite production for the State reached a peak of about 100,000,000 tons a year in 1917, but in recent years production has averaged about 50,000,000 tons, of which somewhat over half comes from this Northern field. The operations of three of the largest producing organizations in the State are almost wholly included in this field, as well as about half of the operations of two others of the six largest producers, It comprises the first 14 of the 25 numerically designated anthracite State inspection districts.

Jan 1, 1937

By Jay D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings for drifts used in block caving stopes. Design data are given that consist of moment, thrust, and deformation coefficients from which bending, axial, boundary stresses, and structural deformations can be determined at any point on the lining. Data is given for circular, horseshoe, and rectangular linings, each with two different thicknesses and subjected to eight different loading conditions for drifts excavated in hard and soft rocks. The structural analyses performed are based on procedures that account for both the structural behavior of the lining and that of the drift and take into consideration deformational interaction that occurs between them.

Jan 1, 1973

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski County, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigations beginning with No. 4251, of which this is the eighth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is no followed by a description of each deposit developed in that half township. The 14 half township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project, except the deep holes drilled to test the geophysical anomalies. The locations at those holes show on figure 13 in volume I. The descriptions of the deposits developed are followed by complete detailed logs at the drill holes. Many at the widely spaced exploratory holes did not discover bauxite of minable thickness and gra.de. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each halt township is given with the discussion covering that area.

Jan 1, 1948

By A. L. Toenges, F. A. Jones, J. N. Sxudder, E. R. Maize

"INTRODUCTION This report is the second of a series of studies of analysis of energy requirements and characteristics of various machines used in the production of coal in underground mines and the losses in distribution of energy to these machines. The test equipment used in these studies is described in Report of Investigations 3615. 7/ The preliminary study data and results of tests made on various types of mechanical-leading cutting, and transporting equipment at two mines. This report is analysis of the energy requirements of the energy requirements of the underground equipment of a third mine. An analysis of the use of energy and its distribution usually requires in a saving in energy consumption and the reduction of hazards. The distribution system should be designed to supply energy effectively and study for the efficient operation of all machines."

Feb 1, 1943

By L. R. Burdick, J. F. Barkley

"There is a general conceit in the coal trade that the moisture- and ash-free B.t.u. of coal from the same seam, and surely from the same mine,is substantially a constant; that calculation of the moisture- and ash-free B.t.u. value from the proximate analysis and B.t.u. determined in the laboratory will reveal whether a coal came from a given area or seam; and that, having this constant, the B.t.u. value of a coal sample can be calculated fairly closely upon a dry or as-received basis from the moisture and ash values of its proximate analysis.To illustrate with a simple example;"

Jun 1, 1941

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the ninth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township map. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948