Search Documents

To provide a flexible, low-maintenance, low-cost continuous mine air monitoring system as an alternative to conventional fixed-point, electronic monitoring systems. Background Continuous monitoring of mine air is highly desirable (and often required) not only to improve miner safety, but also to increase mine productivity. Continuous air monitoring systems can provide earl" warning of developing fires, excessive methane accumulation, reduced oxygen levels, and other developing problems in remote, inaccessible or sealed areas, and in active workings. Fixed-point, electronic systems require one Sensor for every gas to be measured at every defined monitoring location. As the number of monitoring locations increases, so does the cost, along with increases in the time required for routine maintenance and calibration of the sensor System cost also increases when monitoring locations are identified for mine areas requiring permissible electrical equipment.

Jan 1, 1988

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

By J. H. East, D. Harrington

"INTRODUCTION The tremendous expansion of industry during the war and the unprecedented demands for metals and minerals are reflected in the production and use of explosives during that period. The increased use of explosives brought added safety problems to industry because of the necessity of using men as blasters who were not entirely familiar with and some who were totally unfamiliar with the characteristics of some or all of the various explosives. A discussion of the characteristics of the ordinary types of explosives used in: industry should assist in giving a better understanding of the hazards attending their use. Explosives are compounded so they may be used with reasonable safety provided the user understands and follows the procedure recognized as standard safety practice. Short cuts and the failure to understand and use recognized safe practices, as well as the selection of explosives unstited for the work at hand, are all part of the safety problem,The extent to which explosives are used in the United States is shown by a study of the statistics compiled by the Bureau of Mines 4/ regarding them. Some of these statistics are shown below and serve as an indicator of the tremendous number of men engaged in the transportation, storage, and use of explosives. Theme men are exposed to the inherent hazards attending this occupation and they should be familiar with the recognized safe practices relative to explosives."

Sep 1, 1946

By A. J. Farstad

The principle objective of the research effort described herein was to identify as rapidly as possible a practical trapped miner location system. Much effort has been expended in the past on the development of a highly sophisticated seismic location system [1] for trapped miners. Field tests of this system have shown that the location accuracy is limited by a combination of seismic velocity anomalies, timing errors, and in general by the relatively weak nature of the signals received at the surface. It was first felt that similar propagation anomalies would be experienced by electromagnetic systems, but to a greater extent than the seismic. However, preliminary tests performed by Westinghouse on the Operations and Maintenance Program, Contract No. H0210063 in 1971 and 1972, indicated that an electromagnetic solution to the location problem may be more feasible than a seismic solution. Thus a more concentrated effort was launched in 1972 and 1973 to more completely determine the feasibility of electromagnetic location systems for trapped miners. Two different approaches to the location problem were undertaken on this program: (1) A pulsed electromagnetic system was developed by the Special Systems Division of Westinghouse in Baltimore, and (2) a Continuous Wave (CW) System was developed by Westinghouse Georesearch Laboratory (WGL) in Boulder, Colorado. Part I of this report will deal only with the development and results of CW Location System developed by WGL. The CW Location System was field tested at three eastern coal mines and at one western hardrock mine. The maximum overburden depth penetrated during these tests was 990 feet at the Robena No. 4 mine near Waynesburg, Pennsylvania. The earth conductivity at this mine was measured to be 1. 1X102 mhos/m, which combined with the deep overburden make this mine representative of expected worst case conditions for a coal mine EM location exercise.

Jan 1, 1973

By Thomas Fraser

WHEN the Bureau of Mines initiated the program of large-scale research and development in the field of synthetic liquid fuels authorized in the Synthetic Liquid Fuels Act of April 5, 1044, the Coal Preparation Section was assigned the task of obtaining data on the preparation characteristics of the coal in large reserves that might be adaptable to use in this new industry. It is natural that, as the rapidly developing general research program brought about new concepts of raw-material quality, preferred geographical location, and the like, the orientation of coal-preparation investigations should have undergone some change. The first major assignment was the sampling and testing of a series of typical American coals deemed to he suitable for hydrogenation based on early research work conducted by the Bureau of Mines. This first series of tests has been completed and is reported in this paper.

Jan 1, 1950

Major activities of the Bureau of Mines Explosives Research Center during fiscal year 1965 (July 1, 1964, to June 30, 1965) are reviewed briefly. Part 1 summarizes significant accomplishments of the projects that were active during the report period. Part 2 presents short abstracts of the publications that appeared in the Bureau series and in other media during fiscal year 1965. Publications issued after June 30, 1965 are noted where pertinent in footnotes but are not abstracted. ACKNOWLEDGMENTS The Bureau of Mines gratefully acknowledges the support given through cooperative agreements by the following organizations to investigations con¬ducted by the Explosives Research Center during fiscal year 1965: Dow Chemical Company Manufacturing Chemists' Association Monsanto Chemical Company The Sulphur Institute

Jan 1, 1966

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By G. B. Shea

"INTRODUCTION Much of the recent progress in increasing the efficiency of oil-well performance can be attributed to advancements in the art of cleaning wells. Through research and development by operators and service companies during the past decade, significant improvements in the application of engineering and chemical principles to well-cleaning technology have widened greatly the scope of ""clean-out"" methods to the end that greater ultimate recovery of oil will be attained.This report reviews recent improvements and developments on this important problem in California; it describes also the use of various methods and tools for cleaning wells to stimulate or revive their productivity. Developments in preventing and removing mud sheaths in well-completion operations also are described. The report is based on a field survey, supplemented by data from the technical and patent literature and from manufacturers' catalogs, which contain much valuable information.In preparing the material for publication as a Bureau of Mines report, the author has been fully aware of certain limiting conditions that attend the discussion of a subject such as that treated in this report. The following are examples:1. To a considerable extent, well cleaning in California is done with tools rented from service companies, and their representatives and employees are specialists in jobs of this type. They usually have working experience with their own equipment and methods which greatly exceeds that of persons whose interest has been casual or who have had no opportunity to study the subject in detail in actual practice. Many of the tools and methods are covered by letters patent for the protection that may be in developing and successfully applying these mechanical and chemical means of increasing the production of wells. Frequently several years have been required to perfect a given tool or technique, requiring relatively large investments to establish a service that is remunerative to those who have primary interest in a certain development and at the same time attractive enough to the operators of producing properties (because of greater quantities of oil delivered into the flow tanks) to warrant employment of or contractual agreements with a particular service group."

May 1, 1943

By Oliver Bowles

Whiting or Paris white is a fine-grained preparation of calcium carbonate having a wide variety of uses. Until recent years it was prepared almost exclusively from certain north European chalks. With the curtailment of imports of European chalk during the World War of 1914-18, however, finely ground limestone, of domestic origin was used more extensively to satisfy the American demand.

Jan 1, 1942

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By Milford L. Skow

Utilization of domestic ores in the winning of metallurgical alumina requires a convenj.ent method of treating siliceous bauxites and other aluminous materials. In the United states there are only small reserves of high-grade bauxite but considerably larger tonnages of low-grade material. In addition, there are large deposits of high-alumina clays. If these high-silica bauxites or high-alumina clays could be beneficiated, either by are dressing or by chemical dissolution to remove a large proportion of the silica, then the potential reserves of aluminum ores would be increased materially. Faced with a similar situation, the German industry, chiefly dependent on high-grade French bauxites prior to World War II, was compelled during the war to Use lower-grade ores. For desilicating the lower-grade bauxites before the Bayer treatment, a method was developed in which the bauxite was calcined and then given a dilute caustic leach preliminary to the pressure digestion. It was planned to regenerate the caustic by treatment of the desilication liquor with lime. As European bauxites are mineralogically different from those found in this country, preliminary work was undertaken to determine whether this process might be applied to domestic materials. The results of this work, along with a review of the German process, are presented in this report.

Jan 1, 1950

To develop more accurate means of measuring low ventilating air velocities in underground mines to facilitate compliance with ventilation standards. The Approach: A commercially available vane anemometer which produces an electrical, rather than a mechanical, output was coupled to electronic circuitry to produce the Bureau's Digital Low Velocity Anemometer (see photo). [ ] How It Works: The experimental instrument has a vane anemometer head which produces an electrical output signal with a frequency directly proportional to the rotating speed of the vane anemometer shaft. The commercially available ABBIRKO FLOWMASTER anemometer head was used in this instrument. In the signal conditioning circuits the electrical signal from the anemometer is converted into pulses, which are counted during either 3-second or 1-minute intervals, depending on the position of the operator's control switch. (Readout is either "instantaneous" or averaged for a period of one minute.) The number of pulses counted is then translated (integrated and divided by a constant) in the logic circuits to get average speed. Average air velocity in feet per minute is displayed in illuminated digits. (See simplified diagram of circuitry.)

Jan 1, 1975

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

This pamphlet and the enclosed video describe a safe, effective and economical method for removing dust from work clothes. Background Information Dusty work clothes can increase a worker’s exposure to respirable dust. Respirable dust is usually considered to be particles having an aerodynamic diameter of 10 microns or less and able to enter and deposit in the gas-exchange region of the human lung. A former U.S. Bureau of Mines report documented a 10-fold increase in worker dust exposure on a number of separate occasions from dusty work clothes.* It was found that once clothes become contaminated, they are a continual dust source until cleaned. The only MSHA approved method to clean work clothes requires a HEPA-filter vacuuming system which is very time consuming and difficult to perform effectively. Therefore, most workers use a single air hose (not MSHA approved) which can elevate dust levels for the worker, co-workers, and the work environment. A substantial amount of engineering technology has been developed that, when applied, can significantly lower respirable dust exposures of workers at mineral processing plants. But even with these improvements, some workers continue to exceed their permissible exposure limit. Elevated exposures increase the potential for developing debilitating or fatal lung diseases. ?e clothes cleaning method described within is an example of a continuing effort to reduce the potential for developing these lung diseases. Information about engineering research by the former U.S. Bureau of Mines and NIOSH can be found online at www.cdc.gov/niosh. ?is website can also be used for obtaining NIOSH information about health hazards associated with crystalline silica.

By J. M. Mutmansky, L. Xu

"IntroductionSince the establishment of the star,just concentration of 2 mg/m3, a strong effort has made by mining engineers and researchers to provide better dust control equipment and procedures for underground coal mines.Particular areas of success have been implementation of better coal-cutting strategy to control dust generation, better design of water sprays for dust suppression and air movement, use of scrubbers, and improved design of face ventilation systems. A drastic improvement occurred over time such that the average dust concentrations for continuous miner operators dropped from 6.5 mg/m3 in 1968 to 1.3 mg/m3 in 1980 and for auger, cutter, longwall, and roof bolter occupations from 2.7 mg/m3 in 1973 to 1.6 mg/m3 in 1980 (Niewiadomski, 1983).While dust concentrations in mining sections have been dropping considerably, one problem area has been mining sections where quartz is a considerable portion of the airborne dust. The federal regulations require that quartz content must be held below 0.1 mg/m3 in the air regardless of the concentration of the total dust. This legislation limits the allowable dust concentration to a ""reduced standard"" of 10/ (% quartz) when the quartz content of respirable dust in the mine atmosphere is more than 5%. Today, approximately one-third of underground coal mining operations have designated areas with more stringent dust standards in place, and many mines experience considerable difficulty in meeting these standards (Jankowski, and Babbitt, 1989).It is well known that metal miners subjected to respirable dusts high in quartz have a higher incidence of silicosis than those exposed to dust low in quartz. However, the role of quartz in the development of coal workers' pneumoconiosis is still a highly controversial question, in spite of the large number of research projects devoted to this subject over the last 20 years. Because coal seams contain less quartz than metal ores and quartz often comes from sources outside the coal seam (e.g., roof and floor), it is difficult to relate studies that deal with the quartz content in coal seams and the incidence of coal workers' pneumoconiosis. Hamilton, Ogden, and Vincent (1983) have provided a plausible explanation for the incidence of the disease by hypothesizing that the quartz content does not affect the probability of developing pneumoconiosis until some threshold value (generally thought to be about 10%) is exceeded.The objective of the research studies summarized here was to obtain a better understanding of quartz occurrences in airborne coal mine dust by studying the variations of the quartz levels in different dust sizes and the relationship between the quartz content in airborne coal mine dust and the quartz content in the mined material. The implications of the results to control of dust in high-quartz sections will also be discussed."

Mar 1, 1992

By Richard L. Rains

In 1992, the Bureau of Mines evaluated mineral resources of the 34,043-hectare Caribou City and 41,943-hectare Stump Creek study areas in southeastern Idaho. No resources were delineated. The areas had been proposed for wilderness. Rocks underlying the study area are part of the Idaho-Wyoming Thrust Belt. At Caribou Mountain they have been intruded by diorite-monzodiorite. Where the intrusive rocks contact calcareous members of the thrust belt, skarn bodies have formed that host metal deposits. Gold, both placer and lode, occurs in the Caribou City area, and salt occurs in the Stump Creek area. Production records show 73.5 kg (2,363 ounces) of placer gold were produced; however, field studies indicate more than 2,000 kg (67,000 ounces) probably were recovered. Minor amounts of lode gold, silver, and copper were recovered from the hard rock mines. Production of salt from the Stump Creek study area in the 1860's was used by emigrants on the Oregon trail and also shipped to various mining districts for use in silver recovery. Oil and gas were drilled for, but all holes are plugged and abandoned. There are no current leases. Examined workings consisted of 25 adits, 3 shafts, 50 prospect pits, and extensive placer workings all in the northern tip of the Caribou City area, Current BLM records show 168 placer and 146 lode claims; 14 claims are patented.

Jan 1, 1993

By Linneas W. Laage

The purpose of this report is to document the fire experiments conducted at the Waldo Mine, NM during March 1990. The U.S. Bureau of Mines is concerned with improving and validating the predictive capability of the mine ventilation and fire simulator, MFJRE. To accomplish this, fire experiments were conducted at the Waldo Mine and temperature profiles were developed as functions of time and distance from the fire. These tests then provided data for verifying the heat transfer model in the MFIRE mine ventilation and fire simulator. An initial analysis of this data indicates that it will serve this purpose well. This report summarizes the data obtained during six fire tests at the Waldo Mine.

Jan 1, 1994

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979