Search Documents

By H. G. Stephenson, C. W. Gregory

"This article describes the methods used for pillar extraction in the Wilson Seam at Canmore Mines, Alberta. The Wilson Seam is extremely gassy and varies in thickness between 7 and 30 ft, with an average of 12 ft. The gradient varies from 5 to 30 degrees, with an average of 15 degrees. The seam was developed using Lee Norse miners to form pillars which the company intended to extract using the same machines. Before pillar extraction commenced, an abandoned and inaccessible mine 160 ft above the Wilson had to be drained of 360 million gallons of water. When this was done pillar extraction commenced. Conditions in the mine slowly deteriorated and after 6 months the decision to withdraw the continuous miners was taken. Slusher hoists were installed to replace the continuous miners, with the result that roof conditions and safety steadily improved."

Jan 1, 1972

By Tyson Birketi, Françoi Robert, Steve Green, Dan Richardson

Detailed sampling using a portable diamond drill, and inter laboratory comparison of selected samples have been combined with statistical studies of truncated populations to establish the gold content of several outcrops in the Val d'Or area. The outcrops chosen are non-mineralized. The background gold concentration in the rocks of the region is 5 ppb or less. Gold is distributed relatively homogeneously within the outcrops studied except for slightly increased concentrations within quartz-tourmaline veinlets. Three samples, of which 20 grams of powder are analyzed for each, can adequately determine the gold concentration of a structurally simple outcrop in the Val d'Or area.

Jan 1, 1992

By J. Budac, E. Krause, C. L. Stewart, D. Wrana, S. W. Laundry

"As part of an over-all arsenic management strategy, Inco has developed a novel process that converts a by-product high moisture copper/arsenic sulphide precipitate into a crystalline copper arsenate suitable for the manufacture of wood preservation chemicals.The copper/arsenic sulphide precipitate is atmospherically leached with oxygen and sulphuric acid, producing a crude (blue) copper arsenate precipitate, elemental sulphur, and a copper and nickel containing solution. The blue copper arsenate is dissolved with sulphuric acid, the molar Cu/As ratio is raised to 2, and a crystalline copper arsenate (olivenite) is precipitated by the addition of sodium carbonate. Dissolved copper is recovered using metallic nickel (or matte) and elemental sulphur, to produce a low-moisture (low-arsenic) precipitate suitable for standard nickel-copper processing.The process was successfully piloted at Inco's Manitoba Division between September 1990 and June 1991. The copper arsenate product typically analyzed 43% Cu and 25% As, and the moisture content was about 10%."

Jan 1, 1995

By J. A. C. Fortescue

During the past decade, geochemical prospecting methods have become important in Canadian mineral exploration. The object of this paper is to discuss the role of geochemical methods in a typical mineral exploration program involving parallel geological and geophysical methods applied at different degrees of intensity. Particular attention is given to the description of the degree of development of geochemical prospecting under different kinds of local conditions.

Jan 1, 1967

By J-g. Cui, X-b. Guo, J-j. Wang, J. Qiao, H. Tian

"Rare earth elements have unique properties because of the special electronic structure. In this paper the improvement of refractory material performance by the light rare earth oxides was introduced. The experiments showed that adding a bit of rare earth oxide could obviously improve the performance of the refractory material. INTRODUCTIONIn recent years, refractory materials are widely applied in the steel smelting process as a ladle lining material. In China, although the total production of fire-proof material exceeds normal demand, but the quality and variety of fire-proof material still have a big gap with world advanced level. A number of refractory products need to be imported from abroad. With the rapid development of domestic steel production, the ladle lining with refractory is gradually running after the world advanced level on production technology, production variety, and quality level. It replaces some imported products meeting the needs of the development of the iron making production. Therefore, there is an important significance to research on solving the problems of the ladle refractory reasonably and avoiding or reducing blind and not proper use of the imported refractory ( Jing, 2007).On the other hand, rare earth oxide has some special excellent properties. Firstly, they are very good refractory materials with their high melting point;Next, they have good resistance to water and alkali resistance function;Thirdly, it is easy for rare earth oxide to generated composite oxide reacting with other metal oxide,achieving the purpose to improving the material properties (Xu, 1978; Diao, 1979). China has a variety of rare earth resources,and rare earth resources is more advantageous in Baotou,taking up about 36 percent of world reserves,which is the world's top of rare earth mineral. In recent years the rare earth products output has risen sharply and many varieties and specifications have appeared. So it is necessary to study the new field of rare earth compound to open up new markets. Thus, it has a very vital significance to promote the further development of rare earth industry, adjust the rare earth products structure, ease the contradiction between supply and demand, and improve refractory products quality and grade in order to better serve the main body production.I In this paper, the experiments are mainly for 210 tons of Al2O3-MgO style series refractory materials belong to ladle lining bag from Baotou Iron & Steel Group Corporation Sheet Factory. The improvement to the effect of refractory material performance is explored by using light rare earth oxides as additives."

Jan 1, 2012

By Edward P. Barrett

Iron ore, when subjected to reducing gases at a temperature suitable for reduction of the oxide but not high enough to melt the ore or metal formed, is converted into metallic iron. The product, being the original piece of iron oxide minus its oxygen, is sponge-like in appearance when viewed under a magnifying glass, and hence is called 'sponge iron. Sponge iron was probably the form in which some of the first iron was recovered from the ores. As early as the eighth century the Catlan forge developed into a low shaft furnace known as the high bloomary, in which iron was produced in the form of a pasty mass. These furnaces were increased in height, and with increased temperatures came the production of liquid cast-iron, at first undesirable because of lack of knowledge of methods for working it. In 1340 the first true blast-furnace was built iri Belgium. Some castings were made, but the greater part of the iron was converted into wroughtiron blooms by a crude puddling process. Charcoal was the universal fuel until the latter part of the seventeenth century, when coke was first used in England. Larger scale developments of methods of refining pig-iron followed. In I 885 Bessemer built his first converter in England, and within a few years the Siemen' s regenerative open-hearth furnace was developed, also in England, to produce steel. Then followed the enormous expansion in the metallurgy of iron. The idea of a direct process for the production of iron and steel has persisted during all of this time.

Jan 1, 1925

By P. G. Killeen

Proper calibration of portable gammaray spectrometers and spectrometric logging equipment is essential if they are to be used for accurate quantitative determinations of radioelement concentrations. In the case of both types of equipment, it is necessary to determine the system calibration constants (stripping factors and sensitivities). In the case of borehole logging equipment, it is further necessary to determine the system response characteristics if the data are to be computer processed to improve the accuracy and resolution of the logs. Facilities are now available near Ottawa for the complete calibration of portable gamma-ray spectrometers and spectrometric logging equipment, in addition to already existing facilities for calibrating airborne gamma-ray spectrometers. Limited additional facilities are also available or planned in several other areas of Canada.

Jan 1, 1978

By T. Banerjee, Y. Dumais, R. Lemire

"Agnico Eagle LaRonde produces over 300,000 ounces of gold annually, along with silver, zinc and copper by-products. The LaRonde plant consists of a conventional SAG and Ball mill circuit, followed by flotation. Load management is imperative for maintaining stability in grind size and ensuring consistency of the flotation feed. In flotation, the mass pull profiles of the cells and reagent dosage rates need to be managed to maximize recovery, while maintaining product quality. This is achieved by controlling the air, level and reagent addition set-points across the circuit. However, disturbances such as feed size distribution, ore hardness and mineralogy make it challenging to maintain efficient control using traditional control techniques. LaRonde therefore worked to develop a progressive control strategy, targeting stability and optimization. This started with a year-long instrumentation upgrade campaign, focusing on optimizing the performance and reliability of plant-wide instrumentation. The process was then optimized, leveraging AwaRE advanced controllers running in closed loop with PARC modules embedded within the PLC. The installation of 8 PFC cameras in flotation changed the flotation operation from a level and air control based strategy, to one that controls mass pull. This new control philosophy has allowed the plant to effectively manage mill load, improving grind size and providing increased throughput with better flotation performance.INTRODUCTION Background Since 2015, Agnico Eagle LaRonde has been conducting an optimization campaign to maximise the performance of plant assets leveraging instrumentation and control. The grinding and copper flotation circuits were identified as the areas having the greatest opportunities and value proposition for advanced control. A disciplined approach was followed to design and implement a progressive control solution to achieve operational excellence."

Jan 1, 2018

By E. Herrera Alarcón, L. Mariscal Samaniego

The Teniente Converter (wet charge type) was commissioned in august 1995 and was designed to smelt 744 tpd (metric tons per day) of dry copper concentrates. Its products are white metal (73% Cu) that is sent to the Peirce Smith converters, slag that is cleaned in Reverberatory Furnaces and the process gases that are sent to the Sulfuric Acid Plant. Since its start up, the Teniente Converter smelting capacity was increased 1.6 times, from 800 tpd to 1,280 tpd using 33% oxygen-enriched air, and reaching an operative availability of 97%. By the other hand its campaigns have reached a record duration of 530 days without hot patching tuyeres and a partial refractory lining repair in the last four campaigns. This paper describes the most relevant improvements, as well as the strategies that had been used to reach these achievements.

Jan 1, 2007

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

The paper will cover the basic reasons for alkaline leaching, a brief description of the circuit and the reasons for the flowsheet used. Changes made to the flowsheet, including the use of mechanical agitation of pachuca slurry, the use of oxygen and its effect on extraction, the use of lime and its effect on process economy, and the environment, will be described. A brief description of a unique semi-autogenous mill and future circuit changes will be included.

Jan 1, 1979

By Marvin E. Lane

Viburnum, located in the foothills of the Ozarks in south-east Missouri, is the site of a modern lead mining and milling operation. Two mines are currently producing a total of 5,000 tons per day and a third mine is in the final development stage, with full production scheduled for late this year (1964). These mines will supply the tonnage required to keep the Viburnum mill operating at a full capacity of 7,000 tons per day for many years. The efficient underground mining operation is completely trackless. Drill jumbos are used to break the ore in a room and pillar method of mining. Transloaders, or St. Joe shovels, and trucks do the loading and hauling. The Viburnum mill has a world-wide reputation as a most efficient operation. This is due to the extensive use of automatic process controls, and labour saving materials handling facilities. Introduction THE St. Joseph Lead Co., has operated lead mines in southeast Missouri for 100 years. These operations have been confined largely to the area called the

Jan 1, 1964

By K. Heid

"Although concentrated efforts have been made to deplete PCB transformers from the Canadian environment, numerous transformers (as well as ballasts, capacitors and magnets) continue to exist throughout the Canadian mining industry. The existing installed base is slowly being phased out as environmental issues come under increasingly high profile. The following article identifies the potential problems of owning PCB transformers and offers some solutions for their removal, disposal and replacement. IntroductionPolychlorinated Biphenyls (PCB) are synthetic chemical compounds consisting of chlorine, carbon and hydrogen. PCB was widely used in transformers due to its physical properties, including stability, low flammability and non-conductivity. Use of PCB in electrical equipment has been banned since 1977 when the extent of environmental contamination was discovered.Although PCB’s have been outlawed for use in electrical equipment since the late 1970s, safe storage regulations were not addressed until 1988 when a major spill prompted the federal government eventually to issue the storage of PCB Material Regulations in 1992. These regulations replaced the Interim order of 1988 under the Canadian Environmental Protection Act.PCB transformers are usually referred to as askarel filled transformers or as PCB contaminated mineral oil transformers. Askeral transformers were designed to contain high concentration PCB fluids, referred to as askarel. Mineral oil transformers were not designed to have PCB concentrations but were inadvertently contaminated during manufacture or maintenance activities."

Jan 1, 1998

By Jozef S. Stachula

"INCO Limited operates eleven under-ground mines in the Sudbury area. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 km and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55 000tonnes per day.Over 40 surface fans have been installed since the late 1960s. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 m3/sec. to 330 m3/sec., with motors from 100 hp to 2500 hp.Fans of the axial flow type have been commonly used for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages.The surface area taken up by a typical vertical fan installation is generally about one quarter that of a horizontal fan of the same capacity (Rutherford, 1957). This is not a problem with isolated fans and fat surface out crop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly flavour vertical fans."

Jan 1, 1996

By Xu Wang, Yizhe Zhang, Yangge Zhu, Xiao’ou Xia, Fangming Liu

"The progress of lean magnetite preconcentration in China was introduced in this paper, such as using coarse crushing to reject tailings, and multistage grinding, multistage magnetic separation. The applications of “more crushing and less grinding” process and equipment in lean magnetite preconcentration could reduce production costs effectively. The related analysis and study on concrete cases were carried out in this paper.INTRODUCTIONIn the case of the slowdown and weak recovery in the global economy, bulk commodity prices fell sharply in 2015. Take iron ore's prices for example, about 60% grade iron ore's import prices in China from about $65 per ton at the beginning of 2015 fell to about $42 per ton in the end of the year, down by about 35%. But iron ore resources are non-renewable resources, with the continuous development and utilization of mineral resources, high grade iron ore resources will be exhausted gradually. Accompanying with the economic recovery iron ore prices after this fall is bound to return to its value to maintain a high level.The development and utilization of resources is gradually turning to the low grade iron ore. Restricted by technical development level and disadvantages of lean iron ore resources, the cost of utilization lean iron ore resources is relatively high. Making full use of their rich lean ore resources has become many countries' important strategy to get rid of dependence on foreign countries' ore. Over the years with the development and progress of lean magnetite mineral processing technology in China, the production number of concentrator has been greatly improved.As the world's largest steel producer and consumer countries, ensuring a stable and continuous supply of iron ore is particularly important for the healthy development of China's iron and steel industry. Chinese iron ore production and import data in recent years are showed in Table 1.With the expansion of iron and steel production, iron ore demand has also been a phenomenal growth. Taking 2013 for example, China's crude steel production is about 780 million tons in 2013, accounting for about half of the world's total output of crude steel. At the same time, China is also the first major iron ore import countries whose iron ore imports in 2013 was about 820 million tons, an increase of about 10%. The degree of external dependence is very high. In some years, the cost of China's iron ore imports was even more than $100 billion, and second only to oil’s import cost in all bulk commodities."

Jan 1, 2016

By L. Hacini

The start-up is the most critical phase of the cell life, as an uncontrolled start-up could lead to early infiltrations, instabilities, and in some cases to the cell death. Lots of efforts are put to increase the lifespan of cells, as it has a major impact on both the operating costs and the environmental footprint of the aluminum industry. Obviously, a true size test on a cell is a resources- and time-consuming approach that could be used only to validate mature concepts. Moreover, numerical modelling is a low-cost and versatile tool capable to test a wide range of potential ideas and concepts. In the present article, a thermal electrical mechanical slice model is presented. This model describes the preheating and bath periods of a P155 aluminum cell start-up, as used at the Grande Baie smelter. The impact of sodium diffusion and expansion is also included in the model. This model will be useful to study different problematical issues such as the global behaviour of lining materials, shell and cradle deformations during start-up and several start-up scenarios. Such a model will also be able to answer some interrogations regarding early infiltrations and their impact on the lifespan of the electrolysis cell.

Jan 1, 2011

By H. J. Handewith

"After having performed qualitative and quantitative tests on nearly 550 rock specimens from tunnel projects throughout the world and comparing the results with actual boring in eight distinctly different rock types which varied in compressive strength from 12,000 to over 34,000 psi, it has been concluded that any rock -andesite, granite and even taconite -can be machine-bored. The question is -can it be bored economically? The intent of this paper is to delineate the investigative needs to accurately and reliably answer this question. A piece of NX core in the hand represents less than 50 per cent of the worthwhile geologic information that could have been obtained from a given core hole. A thorough site investigation by competent personnel can gene-rally foretell to what extent, if any, varying geologic conditions will hinder machine progress.A laboratory testing technique has been developed that has been correlated well (80 to 120 per cent) with actual boring results. This technique will be discussed in detail. Rock cutter life is a function of the penetration rate and the forces required to sustain that rate. Cutters are now, and will be for .some time to come, the single, most expensive consumable item involved in continuous tunneling in hard rock. It is by strict attention to predicting these rates and forces that tunneling costs can be optimized."

Jan 1, 1970

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By W. I. van Drunick

The Anglogold Ashanti (AGA) Navachab single stage SAG mill has provided an excellent setting for incremental optimization. Over the past decades, several interventions have resulted in marked improvements in specific performance; including steel ball scat removal, re-design of the mill lifters, replacement the pebble crusher and cyclone cluster, as well as the use of a vibrating screen in place of a discharge trommel. Recent initiatives now include an operating fine DMS circuit, studies on pre-crushing of the ROM feed and also fine-screening as an alternative to hydrocyclone classification. The current optimized state of the Navachab mill allows it to operate at approximately 20% higher efficiency when compared to mills of similar shell dimensions in gold mining, treating similar ore. This paper describes the systematic improvement of the SAG circuit to its current state.

Jan 1, 2012

By C. H. Lee, T. T. Wang

"Exampling of the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, this study investigates the application of the Drilling Survey System (DRISS) in both Drilling and Blasting (D&B)- and Tunnel Boring Machine (TBM)-excavated sections. In the D&B section, a nonlinear relationship exists between drilling energy and uniaxial compressive strength of rock mass, in which a reasonable coefficient of determination can be analyzed statistically. Additionally, the DRISS accurately predicted an unfavorable section with a valuable position. The magnitude of uniaxial compressive strength back calculated using DRISS data also matches those acquired from geological investigations with different approaches. Study results indicate that the DRISS is an effective tool for fore-probing of both D&B- and TBM-excavated tunnels. INTRODUCTIONModern advancements in geological and geophysical investigations, and drilling techniques, have provided valuable information for detecting and interpreting geological conditions of rock tunnels with a resolution of several to ten of meters (Brückl et al., 2001, 2008, Lorang et al., 2005). Nevertheless, construction risks remain considerable during tunnel excavation, especially when a tunnel was excavated by a Tunnel Boring Machine (TBM). Predictions of the local fault, shear zone, and other minor geological features, which may cause moderate collapse or excessive deformation of rocks surrounding the tunnel, before tunnel excavation is highly desirable for high-quality tunnel construction and economically efficient project management.Rather than conventional geophysical prospection methodologies, which always favor large-scale investigation with moderate precision, this study focuses on the drilling method probing ahead of a tunnel. The goal of such an investigation is not only to prevent catastrophic collapse, but also to provide quantitative or semi-quantitative information for estimation of the mechanical parameters of rock mass.For the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, a drilling survey system is adopted for fore probing. Data collected from both drilling and blasting (D&B) and TBM-excavated sections are analyzed statistically and discussed. The applications of the Drilling Survey System (DRISS) are addressed accordingly."

Jan 1, 2015