Search Documents

By M. Epiney, A. Ghahreman, R. Kim1and

"Pre-oxidation and cyanide leaching behavior of gold in the presence of sulfide minerals were reviewed, focused on the effects of oxygen injection in the gold leaching process. Generally, pre-oxidation and gold leaching kinetics from iron sulfide refractory minerals, such as pyrite, pyrrhotite, marcasite, pentlandite and arsenopyrite, can be enhanced with higher dissolved oxygen (DO) concentration. However, most of copper sulfide minerals dissolved well both in water and cyanide solutions, and copper from the minerals consumed DO and cyanide to oxidize and leach. Only in the presence of chalcopyrite, gold leaching was effectively occurred with increasing DO. However, chalcocite and covellite severely retarded gold leaching. Stibnite, an antimony mineral, formed a passive film on the gold surface under any DO conditions, and it slowed gold leaching. This impeding effect can be alleviated by leaching at low pH or adding lead salt. Using oxygen and lead together can make synergistic effect in oxidation of sulfide minerals and can enhance gold extraction. Depending on the mineralogical characteristics of the ore, the optimum DO and lead concentrations can be optimized. However, lead can cause environmental problems, and so its dosage should be minimized or eliminated by substituting it with oxygen injection.INTRODUCTIONGold ores containing sulfide minerals are becoming more significant as high grade gold oxide deposits are continuously becoming difficult to find. In light of this situation, to produce more gold, recovery methods from refractory gold ore containing various sulfide minerals should be investigated. Generally, sulfide minerals have impeding effects on gold leaching: formation of a passive film on the gold surface, high consumption of chemicalssuch as cyanide and oxygenduring leaching, reduction of gold cyanide by sulfide ions, etc. (Senanayake, 2008). Therefore, sulfides must be properly treated for better gold recovery. Pre-oxidation of sulfide minerals by injecting pure oxygen can decrease the impeding effects in gold leaching. Prior to cyanidation, sulfide minerals can be oxidized to metal hydroxide and sulfate form, which consume negligible cyanide in the following cyanidation circuit (Bodnaras et al., 1993). Moreover, gold cyanidation can be enhanced by increasing concentration of the dissolved oxygen (DO). In general, the optimum concentration ratio of [CN-]/[O2] is calculated as 6, but it goes higher in the real system (Marsden &House, 2006), which means that the reaction is typically controlled by DO concentration."

Jan 1, 2017

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

By W. Pietsch

For a number of reasons, solids entering and leaving facilities for the treatment of minerals are becoming increasingly finer. Such materials pose problems throughout processing. Solids featuring small particle sizes tend to dusting, result in losses and segregation, exhibit various storage, transportation, and metering problems, and fine particulate effluents can not be easily captured, used and/or recycled. Sustainable mineral processing must minimize the exploitation of natural resources and avoid the need for disposal of wastes. The first requires the use of lower quality raw materials and upgrading, which typically results in the production of fine grained concentrates, and the latter encourages the recycling of wastes and byproducts or efforts to investigate them as sources for secondary raw materials or other beneficial applications. To overcome the difficulties associated with fine particulate solids, size enlargement by agglomeration is necessary. The resulting products have free flow characteristics, do no longer dust or segregate, and are sized and shaped as required for optimum processing. In addition, agglomerated materials may be engineered to feature desirable structure, composition, and a number of related, improved properties. Such engineering may be applied for the modification of fine run-of-mine and up-graded minerals as well as the production of secondary raw materials from by-products or wastes. By the interdisciplinary application of size enlargement by agglomeration waste-free processing of minerals becomes feasible.

Jan 1, 2004

By Karl J. C. Harries

"4.1. INTRODUCTIONThis chapter, although divided into four parts, deals with only two principal topics. The first briefly describes and discusses some common types of property interests and considerations relating to them and the second deals with entering upon privately owned lands and obtaining the consent to do so.It should be noted that the terms “mining rights” and “mineral rights” are used interchangeably. As so used, they include the right to exploit the minerals and dispose of them for the benefit of the owner/lessee. This is relatively common in common law jurisdictions. In some jurisdictions, the two terms have distinct meanings, with “mining rights” referring to the right to work or exploit the minerals and “mineral rights” referring to the minerals themselves.Finally, it must be mentioned that the comments in the Introduction and §§ 4.2., 4.3. and 4.4. are based primarily upon Ontario law and Ontario’s mining and real property systems of registration. They have been included for illustrative purposes.4.2. LICENCES, CLAIMS, AND LEASESIn most jurisdictions, there are several basic types of interests that can be obtained from the state for mining purposes and that are of interest to the explorationist, as opposed to the operator. Different jurisdictions will have variations of these and possibly some extra ones that will address special purposes or local concerns. In virtually every jurisdiction, privately owned property rights are obtained through negotiation between owner and acquiror.Exploration or prospecting licence. This licence grants to the holder the right to prospect over a large tract of land and the exclusive right to acquire mining claims within that tract for the term of the licence. Such licences are usually negotiated documents requiring a minimum expenditure during the first year (often secured by a deposit or surety bond) and minimum annual expenditures thereafter to continue the licence in force up to its full term. The term will rarely exceed four years. The number of claims permitted to be staked will be limited in some way, possibly as to a maximum aggregate area or a maximum number of claims per annum. It is normal for the holder to have to drop part of the licensed area each year, so that the area shrinks annually, although exploration expenditure requirements will usually increase.These types of licences are usually used by governments to encourage exploration of otherwise unattractive or remote areas, such as the far northern parts of some of Canada’s provinces. They do not grant any real property interest in the area for which they are issued, and they will be subject to any claims or property rights that exist in the area. They are contracts with the state that grant certain exclusive rights in return for commitments to carry out work. They may or may not be specifically authorized by statute."

Jan 1, 2003

By N. Behnood, W. Pascheto

"Laboratory wear tests are important tools that can be used for the evaluation of materials for wear applications and mitigation of wear problems in the mining industry. However, laboratory test parameters must be fully characterized and test results must be carefully interpreted if a material selection is to be made. Failure to do so may lead to erroneous conclusions. Suitable lab-oratory tests are valid only if they reflect the field conditions to which materials are subjected. Therefore, it is important to know, in detail, the field conditions, as well as the wear test techniques being considered. It is important to recognize the limitations of the various wear tests and the wear test data published in the literature. This work will review present wear testing technology, including the various wear tests avail-able, wear test equipment and test limitations. Several wear test procedures will be related to common equipment used in the mining industry.IntroductionThis paper will concentrate on non-lubricated wear mechanisms, because they are the most costly to the mining industry. Very frequently we are faced with the task of selecting materials for wear applications or improving existing systems that are giving poor performance. There are plenty of examples in the literature of practical wear cases and ranking of materials for wear applications. It is also very common to find materials manufacturers’ data -sheets listing wear tests results by comparing their materials performances against those of competitors. Much of the published wear data lack the description of the type of wear test, test parameters and the type of wear mechanism to which the data should be applied (if any).Before considering wear test data for a specific problem one should ask which type of wear mechanism is involved? What type of test and what test parameters were used to produce the results? Even if the type of wear tests and parameters are known, how accurate and useful are the published wear data? How are the results related to a particular type of wear? It is important to point out that even the standardized wear tests, such as those in ASTM standards, have limitations. Such limitations are recognized and clearly spelled out in the standards themselves. Basically, wear tests may lead to erroneous results if the test is not able to repro-duce the same wear mechanisms encountered in the field. Therefore, the use of published results may be helpful, as a starting point, but may be of little value for a final material selection.This work will discuss the main types of non-lubricated wear mechanisms encountered in the mining industry. In addition, it will discuss the many wear tests available and their correlation with the various types of wear mechanisms. The limitations of several standardized wear tests and the limitation of using published wear data will also be discussed."

Jan 1, 1997

As a bubble travels through the pulp region of a flotation cell, it will collect the most hydrophobic particles of an intermediate particle size range, this being the primary source of true flotation selectivity. Despite its role on bubble-particle attachment, however, particle hydrophobicity is still missing a mathematical definition that can be used for plant simulation. In this paper, particle hydrophobicity is defined in terms of the induction time necessary for attachment and then linked to the mass of collector adsorbed per particle. This allows particle hydrophobicity to be written as a function of density of collector adsorption as well as particle size and mineralogy. The model is calibrated from the experimental measurement of the flotation rate constant. Liberation data from an industrial flotation rougher is used for model validation. It is demonstrated that the model can describe a broad experimental dataset by means of a minimal number of parameters. Main industrial application is in simulating the effect of the chemical environment upon plant metallurgical performance.

Jan 1, 2006

By W. E. MacDonald

This paper relates the story of 100 years of mining in the Harbour Seam at the Princess Colliery, Sydney Mines, Nova Scotia. Several interesting anecdotes are included along with the discussion of the evolution of coal mining methods in the area. Finally, some of the recently introduced equipment at Princess Colliery is described, and prospects for the future of the industry are outlined.

Jan 1, 1968

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

By N. Shi, T. G. Joseph

ABSTRACT Before any large plant is moved onto an oil sands dominated surface, particularly those surfaces encountered in-pit, it is imperative that the ground be evaluated for bearing capacity. A 2230 tonne mobile in-pit hopper/crusher facility designed for operation in the Canadian oil sands was modeled. This evaluation focused on track and outrigger pad versus ground interactions as the key performance indicators of appropriate ground performance below the unit in both operating and repositioning propel modes. A study of cyclic oil sand behaviour was also inferred from laboratory cyclic plate load data as an extension of the simulation model indications.

Jan 1, 2013

By A. Chamanara

The gross vehicle weight (GVW) of an ultra-class mining truck comprises the unsuspended weight below the struts plus the suspended empty vehicle weight, plus the payload. Theoretically, one third of the suspended total weight is supported by two front struts and two thirds by two rear struts. However, since the payload position is not fixed when placed in the truck body and varies from load to load, compounded by uneven haul road profiles, the truck structure experiences higher than normal stresses, which manifest in the reduction of the life of the truck via structural fatigue. The downstream effects are a decrease in production and increase in operational and maintenance costs. In order to control the dynamic forces causing the high stresses on the truck structure, both the haul road conditions and the load distribution in the truck body need to be investigated. The latter aspect is the prime focus of this paper. A field test has been conducted in an oil sands mine where the Caterpillar 797B trucks are loaded by a Bucyrus 495 shovel. The strut pressure readings are collected using the data-loggers on the trucks as well as the truck velocity associated with each reading. Rack, roll and pitch are the main key performance indicators (KPIs) that are calculated to study the adverse effect of an unbalanced payload and consequently the truck structure. Finally, the shovel bucket load passes within the truck body are simulated and a new method is suggested to improve the truck payload balance.

Aug 1, 2013

IDS: The Company IDS Ingegneria Dei Sistemi, founded in 1980, is a world leader as a high technology solution provider in selected niche defense and civil market sectors ? Private and Independent ? IDS?s Quality System is certified ISO 9001 Ed. 2000 ? IDS has the highest Military Clearance ? Continuously measure (24x7) mine wall movements with sub-millimetric accuracy at long distance (up to 4 Km) ? Provide reliable early warning for progressive slope movements potentially leading to mining wall failures ?Map the long term evolution of slow moving slopes to get a better knowledge of the rock mass strength

Aug 1, 2013

By J. E. Gill

THE 1938 season was marked by a distinct lull in exploratory activity in the Province of Quebec. Quebec was not unique in this respect, but the condition appears to have been more acute here than in most other parts of the Dominion. Various causes may be suggested to account for this. The general disturbance in political and economic conditions throughout the world has certainly had an adverse influence. Uncertainty induced by changes in the mining laws of Quebec in 1937 contributed. A third cause was the belief, now held by many, that the easily accessible deposits in the main producing belt extending eastward from. the Rouyn district have now all been found and that new discoveries in this field will henceforth come more slowly and more expensively. A fourth is the lack of conspicuous success by companies and individuals who have interested themselves in less accessible areas to the north, notably the Chibougamau district. A fifth, the unattractive appearance, as viewed on published geological maps, of the vast area extending northward to Ungava bay and Hudson strait. A sixth, the attraction of such speculative funds as were available to the Northwest Territories, where spectacular finds were reported in the fall of 1937. Whatever may be the relative importance of these causes, languor in exploration will ultimately be reflected in production returns. This appears, therefore, to be an opportune time to take stock of the general position of the Industry in the Province and to consider ways and means of counter-acting those conditions which are now impeding, or will in the near future impede, its expansion. At the request of the Institute Secretary, Mr. Carlyle, I have prepared a brief summary of accomplishments to date and a discussion of some of the geological aspects of the problem.

Jan 1, 1939

By David Scott, Denis V. Lachance, Daniel Marcotie

"LocationThe Heath Steele mine is located 50 km northwest of Miramichi, New Brunswick.Brief DescriptionHeath Steele is a 2700 t/d, copper-lead-zinc operation which employs conventional crushing, grinding, and differential flotation.HistoryThe Heath Steele mine is located in northeastern New Brunswick approximately 50 km northwest of the city of Miramichi and 65 km southwest of Bathurst. The massive sulphides containing ore values in zinc, lead, copper and silver were discovered in 1953 as a result of a joint venture between the American Metal Company and the International Nickel Company of Canada. The discovery was named after Mr. Heath Steele, manager of exploration for Amco at the time of the discovery.Mill production began in February 1957; however, the mine was forced to shutdown in 1958 due to depressed metal prices and metallurgical problems. It was re-opened in 1962 and milling operations resumed at 725 t/d until 1968 when the milling capacity was boosted to 1450 t/d and then to 2700 t/d in 1969.OreThe main ore zones are massive sulphides with very fine mineral grain. The chalcopyrite, galena and marmatitesphalerite occurrences are finely disseminated.Liberation is accomplished by grinding to 68% to 72% <400 mesh. Average mill feed assays are 0.8% to 1.2% copper, 1.8% to 2.5% lead, and 5.5% to 6.5% zinc, with 60 to 75 g/t silver."

Jan 1, 2000

By D. Komljenovic, E. Lafontaine, J. Paraszczak

Availability of the production equipment used in underground mines has a substantial impact on production costs and, thus, on mine profitability. Appropriate collection of pertinent data and information, as well as use of adequate performance measures and their analyses, can help mine operators identify cost-effective opportunities to improve equipment availability. This paper presents study results aimed at reviewing and analyzing means and measures used to quantify equipment availability and its contributing factors (reliability, maintainability and maintenance support) in several Canadian underground mines. It overviews sources, as well as quality and quantity of relevant data and information, and examines performance measures and their definitions, as applied to surveyed mines. Problems concerning data acquisition and meaningfulness of the performance measures are discussed. The paper concludes with some suggestions and recommendations concerning several aspects of equipment availability assessment. Evidence suggests that the latter may become a more useful tool for mine operators in their efforts to reduce production cost.

Jan 1, 2008

By Y. Jin, H. You, H. Pang, B. Lin

Successful application of steam assisted gravity drainage (SAGD) on the recovery of land facies ultra-heavy oil in Xinjiang oilfield depends largely on shortening the preheating period with the aid of the micro-fracturing technology, which is conducted through controlled water injection to a pair of horizontal wells to create homogenously distributed microcracks in the zone between the two wells. The numerical simulation of this mechanical process is yet to be investigated. Up to date, there has been research work on rock mechanics during the SAGD production period of marine deposited ultra-heavy oilsands, but the counterpart research on land facies ultra-heavy oilsands of Xinjiang oilfield is left undone. In this regard, this study is attempted to perform numerical simulation of the fracturing process on land facies unconsolidated oilsands. With this objective, the study first investigates geological and physical identification of the field collected cores, then carries out mechanical analysis on laboratory triaixal test results, based on which numerical simulation of the fractured zone is performed. The simulation is applied through a finite element platform adopting extended Drucker-Prager constitutive model, with the parameters determined by experimental work. It is verified that hydraulic fracturing of unconsolidated oilsands generates a microcrack feature in terms of a dilative zone instead of linear apertures. The extent to which the fractured zone propagates is visually demonstrated based on the magnitude distribution of equivalent plastic strain or volumetric dilation. Evaluation of the connection of injection and production wells can possibly be determined by the expansion of the saturated region around each well. Finally, the implications on the efficiency of hydraulic fracturing in stimulation of the pay zone are investigated.

Jan 1, 2015

By Real Daigneault, François Robert, J. Paul Golightly, Jean-Yves Cloutier, Jayanta Guha, Pierre Pilote

"The Casa-Berardi East, Center and West deposits, located in the Archean Abitibi, Sub province, are hosted by volcanic and sedimentary units of varying compositions, less than300 m from the Casa-Berardi fault (CBF). The CBF, a brittle structure, represents an increment in the structural evolution of a regional-scale deformation zone showing ductile-brittle behavior known as the Casa-Berardi deformation zone (CBDZ). The CBDZ is characterized by a mylonitic Sc1 foliation which is folded a.n4 deformed by a later sczfoliation in high strain zones.Four generations of quartz vein and fracture systems have been recognized within the Casa-Berardi deposits. Most economic gold mineralization, occurring in the second generation system, is found within high strain zones. This system hosts three types of mineralized structures: (1) banded quartz veins; (2) swarms of veins and mineralized host rocks; and (3) disseminated sulphides along fractures. An early carbonate hydrothermal alteration zone (pre- to syntectonic) surrounds the deposits. Alteration associated with gold mineralization is contemporaneous to late ( syn- to post-tectonic) relative to the development of progressive deformation in the CBDZ. The geological characteristics and paragenesis of the four quartz vein and fracture systems developed as an integral part of the geodynamic evolution of the Casa-Berardi deformation zone."

Jan 1, 1990

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By V. Estrada, G. Aguilera

"Since the most of mineral processing are wet, and for more specific applications where it is necessary to increase the purity through leaching and / or concentration, the proper dispersion is the first, and perhaps more crucial stage in the whole chain of processing. This specific process is based on the formation of a dispersion or suspension of mineral, trying to make the mixture as homogeneous as possible, and with specific rheological conditions. Sometimes it is not enough agitation to make it happen, so that chemical additives are used as an aid. However, the addition of chemicals strongly alters the viscosity and other rheological properties of the suspension factor to consider for subsequent steps to ore beneficiation. In other hand, in a process where no chemicals used often employ large quantities of water to achieve dispersion. But if an efficient chemical agent, which optimizes said dispersion through a specific physicochemical effect on the particle surface is used, also it can generate rheological advantages, besides achieving rational use of water and increase the recoveries of the product main about also optimal costs. The aim of this work is to find the optimal rheological conditions for a dispersion of kaolin as study case, looking for stability, best disaggregation, viscosity and pseudoplasticity.To find the optimal additive, the evaluation parameters were: 1) Best degree of dispersion of the suspensions according to the analysis of the flow curve; 2) Best level of disaggregation of particle chemical analysis delaminated by Particle Size Distribution; and 3) Best thixotropic rheological parameters and pseudoplasticity. Finally the optimum additive as one that meets the best combination of parameters is proposed.INTRODUCTIONKaolin is a clay material formed by altering of feldspar composed mainly for kaolinite. Depending on the application, the kaolin as raw material must be refined and processed because the ores of clays contain usually a lot of impurities derived of its sedimentary source, such as feldspar, mica and quartz (Torres, et. al., 2011). According to the experience on the plant floor and the publication of several scientific papers, it is known that the dispersion is a crucial stage in mineral processing (Greene, Duke, & Hunter, 1965) (Raghavan, et. al., 2004), not only because of the disaggregation of particles, besides because of the humectation of them. Is clear that disaggregation of particles give to the suspensions rheological stability, and the humectation improves the effect of further processes like grinding or chemical treatment. The dispersion process involves making a suspension of the mineral with a solvent which is usually water, to obtain a homogeneous dispersion, with the aid of energy of stirring. Sometimes is not enough the agitation (even with high energy) for this to occur, so is necessary the use of dispersing substances which introduce ions and molecules as modifiers of chemical potential, forcing the molecules of the material to disperse. Sometimes their use even could affect the pH of the suspension in a non-desirable condition. (Flores, 2013)."

Jan 1, 2016

By P. Morissette

Passive monitoring of support performance during rockbursts was conducted at three deep underground mines. A comprehensive database was constructed of 172 seismic events and the associated damage to support systems at 266 mine locations from January 2000 to September 2012. The majority of pertinent information was obtained through seismic system records and on-site field assessments. This work assesses the quality of collected information and evaluates the dynamic-load demand on support systems in seismically active mines.

Aug 1, 2013