Search Documents

By Rosie Moore, Harvey Keats, Kerry Sparkes, A. J. Naldrett

"Abstract-The Voisey’s Bay Ni-Cu-Co deposit was discovered in late 1994 as the result of prospecting initiated in the summer of 1993. By July 1995, proven mineable reserves were 31.7 x 106 tonnes grading 2.83% Ni, 1.68% Cu and 0.12% Co, and current total resources in all categories are quoted to be in the order of 150 X 106 tonnes. The deposit is associated with a body of troctolite belonging to the Nain Anorthosite (1.35 Ga - 1.29 Ga) suite, which was emplaced across the boundary between the Proterozoic "Rae" Province to the west and Archean "Nain" Province to the east.The deposit can be described in terms of three geological settings. The "Ovoid" is a 600 m long by 350 m wide by 100 m deep lens of massive sulfide, covered by 10 m to 20 m of glacial overburden, and separated from the underlying country rock quartz-plagioclase-biotite gneiss by a breccia of gneissic fragments in troctolite known as the Basal Breccia Sequence. To the west of the Ovoid lies the "Western Extension", comprising disseminated and massive sulfides in a north-dipping sheet of troctolite which ranges from upper unmineralized troctolite down through troctolite with increasing amounts of sulfide (up to 50%), to massive sulfide (in some places only), and then to Basal Breccia Sequence. East of the Ovoid, the troctolite sheet broadens out into a troctolite intrusion, within which occurs the "Eastern Deeps", a zone of massive and disseminated sulfide up to 100 m thick that is currently being explored. The mineralization of the Eastern Deeps lies along the line of intersection of a feeder sheet with the base of the intrusion. The current interpretation is that the three geological environments represent different erosional levels through a single mineralized intrusion. In this model, the deepest erosional level lies to the west and exposes the feeder to surface, whereas the Ovoid represents the base of the intrusion at surface, and the Eastern Deeps the base of the intrusion overlain by 600 m to 900 m of troctolite. Sulfides and gneissic fragments were brought up by magma flowing quickly through the feeder, and settled out where the flow rate decreased as the sulfide-bearing magma mixed with magma already emplaced in the intrusive body."

Jan 1, 1996

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By Yi Yang, Mark Zoback

"We report laboratory studies of the time-dependent deformation of core samples from four different formations in the Williston Basin - the Lodgepole formation, the Middle and Lower Bakken formations and Three Forks formation. The laboratory tests reveal varying amounts of viscoplastic deformation in response to applied differential stress. The time-dependent deformation is generally greater in rocks with higher clay and organic content, and can be described by a power-law function. Because the magnitude of the creep strain is linearly proportional to the applied differential stress, we can utilize viscoelastic theory and geophysical logs to estimate the degree to which tectonic stress is affected by viscoplastic stress relaxation. We suggest that viscoplastic stress relaxation results in the Upper and Lower Bakken Formations act as frac barriers during hydraulic fracture stimulation in the Middle Bakken, but the Lodgepole and the Three Forks Formations are not frac barriers.INTRODUCTIONHorizontal drilling and multi-stage hydraulic fracturing in shale reservoirs are critical for successful exploitation of ultra-low permeability shale gas, tight gas and shale oil reservoirs. Characterization of the mechanical properties of the reservoir rocks is essential to understanding the behavior of rocks during drilling and completion. Previous laboratory studies have shown that the timedependent deformation in clay-rich shales can be characterized as linear/viscoelastic deformation (Chang et al., 1997; Hagin and Zoback, 2004a, b; Sone and Zoback, 2013b, 2013c). Sone and Zoback (2013c) showed that laboratory measurements of time-dependent deformation in various gas shale reservoir rocks, and demonstrated that the viscoplastic deformation of these rocks can be characterized by a power-law function. They interpreted the results in the framework of linear viscoelastic theory to quantitatively assess the geomechanical effect of viscous time-dependent deformation over engineering and geological time scales. (Sone and Zoback, 2014) further extended the theory and proposed a viscous relaxation model that can be applied to predict the continuous differential stress magnitude using the geophysical logs. They tested the validity of their model by comparing the stress prediction with the occurrence of drilling induced tensile fractures (DITFs) and the vertical hydraulic fracture penetration observed from microseismicity."

Jan 1, 2015

By Réal Tanguay, Mathieu Piché, Jacques Carignan, Charles Beaudry, André Bonenfant

"Le gisement Isle-Dieu est situé sur le flanc sud de l'anticlinal de Galinée. La stratigraphie locale comprend, de bas en haut, la rhyolite du Groupe du Lac Watson surmontée par le basalte du Groupe de Wabassee. Un horizon repère, siliceux et sulfure, d'origine sédimentaire, appelé ""Tuffite Clef', est présent au sommet du Groupe du Lac Watson et pend à 45° vers le sud.Le gisement Isle-Dieu est constitué par une lentille qui recoupe, en partie, la ""Tuffite Clef"". Elle est séparée en deux trorçons par un dyke de tonalite. Les données obtenues à partir des forages effectues à travers la rhyolite sous-jacente permettent de définir les zonations chimiques et pétrographiques de la cheminée d’altération.Ces transformation minéralogiques et chimiques sont caractérisées par un enrichissement en MgO, Fe2O3, MnO et un appauvrissement en CaO, SiO2 et Na2O. La zonation spatiale de ces altérations permet de mettre en évidence la géométrie et l'extension des conduits hydrothermaux. L'épaisseur maximale des sulfures massifs au sein de la lentille est en étroite relation avec l’importance des zones d'altération. Les patrons de variations chimiques dénotent une orientation préférentielle WNW des conduits hydrothermaux. Les parties les plus altérées et les plus déformées présentent localement de fortes variations positives en Zr, Nb, et terres-rares; ces concentrations sont vraisemblablement imputables a /' enrichissement résultant de la diminution du volume lors de l'altération.L'étude pétrographique montre que la porosité et la perméabilité du milieu ont joué un rôle important dans la circulation des fluides car les roches de la cheminée présentent des phénomènes de dévitrification, de bréchification et de microfracturation très prononces. La nature magnésienne de certaines chlorites et la perméabilité accrue du milieu semblent en accord avec le modelé propose par Roberts et Reardon, ( 1978 )"

Jan 1, 1990

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By D. D. Tannant, H. Ozturk

Thin spray-on liners are increasingly being used as rock support in underground mines. The adhesive strength between the liner and the rock surface is an important design parameter. Adhesion tests were conducted to assess the impact on adhesion of the presence of oil, water, and dust on a substrate, and the roughness and grain size of different substrates. Other factors such as curing time, loading rate, and liner thickness were also considered. Adhesion was measured using a pull test of a 33 mm diameter elevator bolt attached to an over-cored section of liner with strong epoxy. Most tests were performed using Tekflex liner material, although five other liner products were also tested. Adhesive strengths of about 2 MPa can be achieved with Tekflex under optimal conditions. Long-term creep tests showed that the adhesive strength could drop by at least 50% when the liner carries load for about a month. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa. As the thickness of the liner increases, the adhesive strength to a substrate appears to decrease.

Jan 1, 2007

By J. T. McGrath, R C. A Thruston

The structural changes which take place in polycrystalline copper under the action of alternating cycles of torsion stress were studied, using the optical microscope and the X-ray dif-fraction camera, and an attempt was made to correlate them with changes in the shape of the cyclic stress-strain curve. It was found that the period of work-hardening was less than one per cent of the fatigue life, and that persistent surface marking, which are assumed to be incipient or actual microcracks, occur upon completion of work-hardening. X-ray diffraction patterns revealed considerable grain distortion at the completion of work-hardening in specimens cycled at a high strain amplitude. This distortion became progressively less as the strain amplitude de-creased. Mechanisms for the completion of work-hardening and the formation of microcracks are discussed.

Jan 1, 1962

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004

By K. Scholey, S. Marcuson

As high grade nickel sulphide ores are being depleted and with the continuing challenges experienced in economically processing nickel laterite ores, it is important to investigate technologies that can extract nickel from low grade ultramafic ores which are present in large quantities worldwide. In the Thompson Nickel Belt, there are some hundred million tonnes of mineralization that are potentially amenable to surface mining. Since the original discovery of the Thompson orebody, recovery of nickel from these ultramafic deposits has been an elusive goal. Research and development projects as well as commercial processing have been attempted. In the 2000's as other resources became scarcer, a major drilling, mine evaluation and research project was initiated at Vale. In 2007, Vale Base Metals Technology Development invited Cytec and potential academic partners to participate in an industry-university research consortium with the goal of developing new technologies and methods of processing the ultramafic deposits. Three university professors, J. Finch of McGill, P. Somasundaran of Columbia and R. Pelton of McMaster accepted, each group attacking the problem with a different approach. This paper describes the management of the research consortium and the significance of the results from Vale's perspective. The next four papers in this session will summarize the project and results from the partners' point of view. Vale is pleased to share the experience of the collaborative research and development with the mining industry.

Jan 1, 2011

This work illustrates the potential of two welding processes for joining AA1100-16 vol.% B4C metal matrix composite: laser welding process using a 4 kW Nd:YAG laser and Friction Stir Welding. A comparison is made between these two welding techniques in terms of microstructure and mechanical properties of welded joints. A large amount of brittle needle-like phases, together with some residues of B4C particles were observed in the fusion zone of laser welded joints. The use of Ti filler can improve the microstructure and increase the joint efficiency from 63% to 75%. On the other hand, the friction stir welding process being a solid state welding technique is interesting as it avoids the formation of brittle intermetallic phases. In addition, the breakage of B4C particles and the grain refinement of the matrix were observed in the weld zone. Consequently, FSW joints show much better mechanical properties than laser welded joints. Up to 100% joint efficiency can be achieved by FSW for annealed AA1100-16 vol.% B4C materials.

Jan 1, 2011

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By A. Manouchehrian, M. Cai

"Rockburst, which often occurs around underground openings in highly stressed hard rocks, is a sudden and violent unstable rock failure and is associated with energy release. Rockburst is very dangerous to workers and mining equipment, and it has been a major concern for deep underground construction and mining. Before excavation, rocks are loaded under a true-triaxial condition. Upon excavation, the rocks at the excavation boundaries are loaded in the maximum principal stress direction and unloaded in the minimum principal stress direction and this provides a necessary condition for unstable rock failure to occur. Understanding rock behavior under true-triaxial unloading condition is critical for developing measures to control unstable rock failure in underground construction.In this article, an explicit FEM tool is used to simulate rock behavior under true-triaxial unloading condition, with a focus on analyzing stable and unstable failure and the released energy during failure. Firstly, a uniaxial compression test was simulated. The results indicated that the adopted numerical tool was able to simulate stable and unstable failure by varying the Loading System Stiffness (LSS). In this research, Loading System Reaction Intensity (LSRI) was proposed as an indicator to identify stable and unstable failure. Secondly, unstable rock failure under true-triaxial unloading condition was simulated. A rock specimen was loaded in three directions; the lateral pressures (s3 and s2) were kept constant and the vertical stress (s1) was increased to a pre-defined stress. The specimen was suddenly unloaded in the minimum principal stress direction (s3) and loading in the s1 direction was continued until failure occurred. Different LSS values were considered and the results showed that the LSS influenced the failure mode; a soft loading system resulted in more violent failure and released more energy than that in a stiff loading system. The influence of specimen height to width ratio on rock failure was also investigated. It was found that failure in taller specimens was more violent than that in shorter specimens. Insights gained from the simulation are useful for better understanding of the influencing factors on the released kinetic energy during unstable rock failure and to find means to control rockburst damage in engineering practice."

Jan 1, 2015

By N. W. Bliss

"Bauxite has been the almost universal ore of aluminum for about 100 years, with most of the world's reserves oc¬curring in the developing countries. As a result of fiscal and political activities prompted in part by the energy crisis, the formation of the IBA combined with increasing freight and labour costs, these reserves are no longer as competitive or as secure as they once were. This has given fresh impetus to the development of processes for alumina production that utilize raw material other than bauxite. Canada has no bauxite and it is prudent to look for alter¬native raw materials within our own boundaries suitable for one of these processes.Of the three igneous rocks that have been used as a source of alumina, only anorthosite is considered as a potential source in Canada. The Al content would be extracted by a sinter process, which currently requires a raw material with a. minimum of 28% Al2O2. Thus, about 4 tons of anorthosite and 10 to 12 tons of limestone are needed to produce one ton of alumina. There are two petrologically distinct types of anorthosite, one containing the plagioclase andesine-labradorite and around 26% Al2O3, and the other containing upwards of 30% Al2O3, in by¬townite-anorthite; for our purposes they may be con¬sidered as low- and high-alumina anorthosite respectively. The high-alumina anorthosites are somewhat rare; the low-alumina anorthosites are much more common, partic¬ularly in Eastern Canada. Geologically speaking, there is no shortage of anorthosite in Canada. The reserves are im¬mense, although their low Al2O3 content coupled with con¬siderations of location, access and proximity to limestone could be constraints to their development. Fly ash from coal-fired thermal power stations and nepheline syenite can also be used in a sinter process, but neither is likely to be utilized in Canada in the immediate future.The H+ process utilizes an acid attack to leach Al from a raw material with at least 20% Al2O3. One of the best raw materials is kaolinite-bearing clay; not only is it high in Al, but most of it can be extracted. With the possible exception of the Whitemud clay in Saskatchewan, Canada is apparently deficient in clays with sufficient reserves to support an alumina plant utilizing the H+ process. Low-alumina clays with illite and montmorillonite may also prove to be a suitable raw material if advantageously sited with respect to industrial centers. The average shale con¬tains only 15% Al2O33, much of which may be contained in minerals, such as feldspar, not amenable to acid leaching. If shale is used as a source of alumina, it will be because it contains some other valuable commodity, such as oil or uranium, the extraction of which leaves the spent shale upgraded in extractable Al2O3 and lowers the over-all costs to a point where it is economic, Thus, rejects from coal washing plants are most commonly considered as a source of alumina; they are already mined, are available in large and ever increasing amounts, and may contain significant amounts of combustible material which upgrades the Al2O3, content of the resulting ash. Coal rejects from existing and developing coalfields in Alberta and British Columbia are a possible source of raw material, but present data indicate they may contain insufficient Al2O3."

Jan 1, 1976

"A numerical procedure based on Smoothed Particle Hydrodynamics (SPH) is developed for rock blasting phenomena involving multiple intersecting joints. In this procedure, an elasto-plastic damage constitutive model has been applied in the framework of SPH to simulate yielding response of the surrounding rock medium. In this paper, a square shape rock medium with centrally located emulsion explosive in a borehole is numerically blasted with and without the presence of two diagonal rock joints. The model is simulated by assuming all four sides of the rock medium as free surfaces. The paper elaborates the propagation of stress wave, expansion dynamics of gaseous products, and development of fracture, fragmentation of the medium and dissipation of energy due to damage.INTRODUCTIONDamage prediction of rock mass and its mean fragmentation size are of important to design blast parameters for a given explosive. Current blasting practice solely depends on empirical relationships between fragmentation sizes to those blast design parameters while mathematical descriptions of the physical laws governing the process of rock blasting are limited. A constitutive relationship based on properties of explosives and rock mass is of special interest because of its capabilities in describing the key features of rock fracture and fragmentation, resulting in understanding of the physical process involved in rock blasting. It is well known that blast-induced damage and fragmentation of rock mass occur due to detonation induced stress wave and product gas driven fracture propagation. Nevertheless, the fundamental mechanism of the failure process and the behavior of rock characteristics under these two different loading are not well understood in many cases, which are closely related to growth of fractures and interaction of cracks under different loading conditions.Continuum damage mechanics is considered to be appropriate to describe the failure process under such high-amplitude stress wave. Based on this approach, several theoretical models have been developed to analyze the dynamic damage of brittle material such as rock and concrete with microstructure (Chen, 1999; Taylor et al., 1986; Wu et al., 2004; Yazdchi et al., 1996). These models are mostly based on the theory of damage mechanics or fracture mechanics with some statistical treatment to incorporate random distribution of microcracks. In the application of fracture mechanics theory, sometimes it is difficult to estimate the micromechanical parameters such as crack density and fracture toughness in different modes. In this study, damage in rock material is evaluated according to the earlier model developed by Grady and Kipp (1980), which is a fracture model coupled with a material description for stress wave propagation to predict quantitatively fracture and fragmentation under explosive loading conditions."

Jan 1, 2015

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By S. S. Yuan, Q. Z. Zhu, J. F. Shao

"This paper aims at enriching a homogenization-based anisotropic damage model for hard rocks under complex loading. A new damage criterion is proposed to capture material strain softening. Within the framework of irreversible thermodynamics, we are particularly concerned with two strongly coupled dissipative mechanisms: frictional sliding and damage by microcracking, which usually take place at cracks within cohesive geomaterials under compression. Focusing on the representative elementary volume containing multiple crack families, the free enthalpy of the matrix-cracks system is obtained. Importantly, a back-stress term is involved in the local stress applied to microcracks. This back stress plays the hardening/softening role in the friction criterion which is formulated at local scale. Strain hardening owns to the accumulation of frictional shearing and dilatancy while strain softening is caused by crack growth. The multiscale damage model is used to simulate laboratory tests on the Westerly granite under true triaxial compressions. INTRODUCTIONWhen subjected to compressive loads, hard rocks present nonlinear mechanical behaviors and induced material anisotropies. In that process, two main dissipative mechanisms have been largely identified: damage by crack growth and frictional sliding along closed crack faces, which are usually strongly coupled to each other on crack scale. Theoretical investigations have shown that the damagefriction coupling analyses allow explaining a large number of experimental phenomena involved in brittle or quasi-brittle materials. Concerning constitutive modeling, the standard Eshelby’s solution-based homogenization procedure for heterogeneous materials was recently applied successfully to describing the mechanical and poromechanical behaviors of cracked frictional solids."

Jan 1, 2015

By J. S. Redpath

There appears to a definite trend toward the hoisting of greater tonnages from greater depths. There is every indication that this trend will continue and we feel that improvements in the design, fabrication and installation of mine guides will be of significant importance in the future. The present state of the art in mine-shaft guide systems is reviewed and the parameters required for improvement are derived in this paper. Finally, a proposal is made for a new steel guide system which meets the parameters and is economical to fabricate and install.

Jan 1, 1977

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960