Search Documents

By E. D. Gardner

The Synthetic Liquid Fuels Act (58 Stat., 190; 30 U.S.C. Sup., Secs. 321- 325) was approved by Congress April 5, 1944; it directed the Bureau of Mines to build demonstration plants to produce synthetic liquid fuels from coal, oil shale, and agricultural products. The most important oil-shale de- posits in the United States are in the Green River formation of Colorado, Utah, and Wyoming. The oil shale of western Colorado generally is more amenable to exploitation, more persistent, and apparently richer than elsewhere in the Rocky Mountain Region. It occurs at the top of a high plateau surrounded by bold, nearly vertical escarpments 500 to 600 ft in height. The top 400 to 500 ft of these escarpments comprises an oil-shale measure that averages 15 gal of shale oil per ton; the bottom 70 to 100 ft of the measure, called the Mahogany Ledge, averages over 30 gal per ton. The full measure in a 1000-square-mile area is estimated to contain 300 billion barrels of shale oil;' the Mahogany Ledge is estimated to contain 100 billion barrels of oil. These estimates are based on numerous surface samples and on core-drill holes drilled by the Government and by private enterprise. The oil-shale beds are undisturbed and lie nearly horizontal. The name

Jan 1, 1949

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By W. H. Blauvelt

THE subject of fuel-briquetting has attracted much attention on the part of engineers and investors for the past 15 or 20 years, and especially in recent years, during which a number of plants have been built, with more or less commercial and technical success. Our technical literature contains numerous descriptions of certain processes, and discussions of the industry in general. For a history of the development of the art in the United States, and for descriptions of many of the processes which have been tried, reference may be made to the files of our Transactions, and, for more recent information, to a paper by C. T. Malcolmson, read before the First Annual Convention of the International Railway Fuel Association in June, 1909. The purpose of the present paper is to describe the briquette-plant of the Solvay Process Co. and the Semet-Solvay Co. at Detroit, Mich., which, after a period of long and costly evolution, is now operating satisfactorily on a commercial basis. I believe that it will be of interest to some of our members to have the details of operation, lower-consumption, labor, etc., as worked out on a practical and commercial scale in a going operation. The briquette industry has had a somewhat checkered career in the United States, and much the larger portion of the failures has been due entirely to commercial causes. It seems axiomatic to say that before undertaking the installation of a plant for manufacturing briquettes it is necessary that the local situation should be carefully examined : First, to determine the kind of briquettes, if any, the local market will consume; that is-to say, whether the available fuel-supply is such that briquettes would be a welcome addition, and whether the most promising field is the industrial or the domestic market. Second, if there is an available supply of raw material, as coal,

Mar 1, 1910

By M. Felsenthal

Engineers are frequently faced with the problem of having to predict oil recovery from a solution gas drive reservoir in the early life of a field. This is often the time when actual laboratory or field-derived gas-oil permeability (kg/k0) data are not yet available. Although excellent collections of k0/k0 data for various types of rocks may be found in the literature,1,2,3 a need exists for a more detailed correlation of k0/k0 data with core properties such as porosity, permeability, clay content or pore-size distribution. It is the purpose of this article to present this type of correlation for sandstone material. The correlation is based on laboratory tests performed on over 300 core samples from 19 reservoirs in the United States and Canada. EXPERIMENTAL Cores were analyzed by routine procedures, using samples of conventional size (7/8-in. diameter, 7/8-in long) cut parallel to the bedding planes. Air permeability was measured at 1.67 atm mean pressure in a Hassler-type apparatus. Porosity was determined with the aid of a Ruska bulk volume meter and a Boyle's Law rock volume meter, An evaporation method' was used to evaluate irreducible water saturations. Core samples were saturated with 25,000 ppm NaCl brine. The brine was reduced to the irreducible saturation, and the remainder of the pore space was filled with kerosene. This was followed by multiphase flow tests using the so-called "dispersed feed" technique.5 n this technique, gas and oil (kerosene and kerosene-saturated air) were dispersed with the aid of a porous Alun-durn feed head, the face of which contained a waffle-shaped system of Lucite-lined grooves. Oil entered the back side of the feed head and emerged at the raised areas of the front face. Gas was introduced directly into the system of grooves at the front face. The gas-oil mixture then entered the test core which was kept in capillary contact with the feed head. Permeabilities were determined from rate and pressure measurements and saturations from weights. All determinations were performed at equilibrium or steady-state conditions. Pore-size distributions were determined on selected samples by a mercury injection technique.6 GENERAL CORRELATIVE TRENDS When examining data from a given reservoir, it was noted that k0/k0 vs saturation curves became generally less steep as specific air permeability increased, a development that has a favorable effect on oil displacement efficiency by solution gas drive. This trend has also been reported by others in the literature.' An effect of porosity on k0/k0 data was also noted. This effect was not generally discernible in a study of relative permeability data for a given reservoir but became apparent when data for sandstone reservoirs of similar lithology but differing average porosity were compared. For instance, in a comparison of argillaceous and/or calcareous sandstones from 11 reservoirs ranging in average porosities from 14 to 28 per cent, a definite trend was noted, indicating that for a given permeability k0/k0 curves became less favorable (i.e., steeper) as porosity increased. A similar trend was observed for a group of comparatively clean sandstones from five reservoirs ranging in average porosities from 15 to 21 per cent. For a given permeability and porosity, comparatively clean sandstones gave more favorable k0/k0 curves than argillaceous and/or calcareous sandstone or chert reservoirs. The laboratory studies also showed that least favorable k0/k0 curves were exhibited by shaly sandstone, conglomerate, and sandstone containing carbon inclusions. Table 1 lists the various source reservoirs classified by lithology types. To facilitate a correlation of k0/k0 data with core characteristcis, it was found expedient to work with

By C. A. Stewart

I. INTRODUCTION AND GENERAL STATEMENT OF RESULTS. The field-work upon which this paper is based was done in the summer of 1910, and was made possible by the courtesy of the Imperial Copper Co., which gave me access to its property. For their kindness in this respect I wish to express my thanks to W. F. Staunton and Meade Goodloe. Moreover,. B. F. Smith and G. B. Gentry, mining engineers in the employ of the company, gave invaluable assistance by placing maps,. etc., at my disposal, and by discussing with me the problems of the district; and it is a great pleasure to acknowledge this indebtedness to them. In order that the significance of some of the details that follow may be better appreciated at first reading, a general outline of the conclusions reached is given here. In the Silverbell mining-district a series of Palaeozoic limestone blocks is completely surrounded by post-Palaeozoic igneous rocks, intruded in the following order: alaskite, alaskite-porphyry, biotite-granite, andesite, and quartz-porphyry. The biotite-granite is believed to represent a differentiation of the. magma from which the alaskite-porphyry came ; and this conclusion-has an important hearing on the origin of the ores. The intrusion of both alaskite-porphyry and biotite-granite was followed by the emission of magmatic waters, which sericitized and silicified the alaskite-porphyry and granite, and produced in the limestone, by the addition to it of silica, iron, and alumina, great masses of garnet, quartz, and wollastonite. Following close upon these solutions came metal-bearing magmatic waters, which impregnated porphyry, granite, and alas kite with cupriferous pyrite, and deposited in the garnet zones chalcopyrite and copper-bearing pyrite that make important bodies of contact-metamorphic ores. Secondary enrichment has taken place in the disseminated ores in the igneous rocks,. raising their copper-content to 2 per cent. in some cases,. and extensive drilling has been undertaken to block out these deposits. East of the contact-metamorphic deposits there is a fissure-vein of lead-silver ore in the quartz-porphyry. This rock is distinctly younger than the alaskite-porphyry and the granite; and the lead-silver ores belong, therefore, to a period of mineralization distinctly later than the copper-deposition.

May 1, 1912

Large deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the .manganese content of manganiferous iron ores in a form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports.' The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treatment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a 1/2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

By Charles Will Wright

The present struggle for economic and industrial supremacy by the Communist world is against the United States, its main target, and the other Free World nations. The basis of industrial power is minerals, so the Communist nations are building up mineral production within their borders, often regardless of costs, and are acquiring quantities of mineral products from Free World countries for future use. They are contracting for additional supplies and advancing funds for the development of these quantities. A number of the less developed mineral producing countries of the Free World are being infiltrated by Communists and Communistic influence. This situation is well known, but as yet little has been done to oppose these activities or to awaken the public to their seriousness. The Communist countries are still far behind the Free World Nations in production of many essential minerals. But, shortages are being made up from Free World nations in exchange for petroleum, manganese ore, chromite and other products. Restrictions on shipments of strategic materials to Communist countries have not been maintained.

Jan 1, 1964

By Stanley Rajnak, John E. Dorn

The saddle-point activation energy for the nu-cleation of a pair of kinks is estimated as a function of the applied stress, the lattice constants, and the height and shape of the Peierls' hill by employing the line-energy model of a dislocation. The kinetics of disloration motion by the Peierls' mechanism are discussed and the microscopic dislocation velocities and macroscopic strain rates are formulated by the Arrkenius type of approach in terms of the activation energy for the formation of pairs of PEIERLS was the first to illustrate that a straight-dislocation line has its lowest energy when it lies in a potential valley parallel to lines of closest packing kinks. The log of the dislocation velocity is found to be approximately proportional to the log of the local applied stress. It is also shown that the low-temperature mechmical properties of several bcc metals might be explained in terms of the Peierls mechanism, good agreement being obtained between theory and experiment for the flow stress us ternperature, activation energy vs stress, and activation volume us stress curves for these metals. of atoms on the slip plane. When such a straight dislocation is moved rigidly from one valley toward the next, the atoms in the vicinity of the core of the dislocation change their positions and bond angles, causing the energy of the dislocation to increase. Midway between two adjacent valleys, the disloca-tion energy reaches a maximum value and any additional small displacement will cause the dislocation to fall down the hill into the next valley. The maximum shear stress necessary to promote such

Jan 1, 1964

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By J. P. Zannaras

If we assume that testing of the model started at time t1, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. I), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t2 after time t2 motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made. It can therefore be stated that all conclusions and observations of the author from the photographs are applicable only to his small-scale experiments and not to actual mine roofs. Without investigation of the true stresses or the combined maximum stress induced in the beds it has been assumed by the author that failure occurred solely due to bending stress caused by loading of the beds. (The author states that D was taken to be the theoretical strain given by elementary beam theory.) Fig. 1 shows that the beds were clamped together. This clamping was necessary to prevent slipping of the beds due to the horizontal shear. However, this clamping caused an uncontrolled and undertermined com-pressive stress S at the end of the beds, and this com-pressive stress caused a true tensile stress ?S (? PoiS-son ratio). This true tensile stress combined with the tensile stress produced at the end of the beds due to loading (fixed beam uniformly loaded), and the horizontal shear which is maximum at the end appears to be the most probable maximum stress produced in the beds. It is therefore evident that the author in performing this experiment has introduced stresses in the model not existing or dissimilar to actual mine roofs, and therefore his conclusions may be applicable to his small-scale experiments but inapplicable to actual mine roofs. Louis A. Panek (author's reply)—The discusser's difficulty is related to mechanics of materials rather than similitude. The effect of time did not enter into the tests in any way, being simply excluded from consideration in this study, because all quantitative results entering into the design equations are based on measured (between time t1 and time t2) bending strains that are well below the breaking strain (i.e., in the elastic range) for the model material. Time does not become a significant factor until the rock stress reaches 80 to 90 pct of the breaking stress." The objective of this investigation was not to predict that bolted roof will fail after time t, but was instead to develop a safe roof, that is, roof in which the bending strain is much less than (say less than 50 pct of) the breaking strain. The models tested to failure had no direct bearing on the design equations. Although for some rocks time may influence the magnitude of stress or strain at which fracture occurs, breaking stress or breaking strain values were not employed for any purpose in this investigation. Tests to failure were made only to obtain additional evidence regarding the behavior of the bolted laminae' as evinced by the locations of the cracks. As stated in the last paragraph of the paper, if one wishes to predict the time or stress conditions for which the roof will fail, additional information is required. The reason for clamping the laminae is to make them behave liked clamped beams, which closely approximate the clamped-plate condition of the actual mine roof beds (Ref. 5, p. 1; Ref. 6). The writer has previously demonstrated that the bending stresses induced by centrifugal loading in a clamped model beam are in agreement with those predicted by theory;' hence clamping has no significant effect on the bending ,trains measured during a test. Moreover, actual ,in, roof beds are likewise subject to a clamping effect due to weight of superincumbent strata carried by the pillars or ribs on each side of the opening. It is emphasized that this study was restricted to evaluating only the reinforcing effect produced by the bolts. Procedures employed in the experiments and in the data analysis were such as to deliberately exclude the effects of other factors. The objections offered are therefore invalid,

Jan 1, 1957

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler's saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By D. Kunstelj, M. Stubicar, A. Tonejc, A. Bonefacic

A. Bonefafcic, D. Kunsfeli, M. Stubicar, and A. Tonejc The present communication is concerned with the variation of the texture in aluminum wires with die angle and temperature, at constant speed of extrusion. Experiments were carried out concurrently on refined samples, with a stated purity of 99.997 pct pure A1 and commercial samples of 99.5 pct Al. Ingots of refined aluminum samples were machined to 30-mm-diam by 150-mm-long billets. These billets were transformed to 5-mm-diam wires by drawing. The final form, suitable for examination, was obtained by extrusion through conical-face dies with a 1-mm hole diam and extrusion ratio 5:l in diam. The initial form of the commercial aluminum samples was drawn wire 5 mm in diam. These samples showed a poorly defined texture with (111) as a major and (001) as a minor component. A similar defined texture appeared in the refined aluminum samples after drawing to 5 mm diam. Conical-face dies with different angles (defined by the axis and the generating line of the cone) were used in our experiments. The values of the angles were 27, 35, 45, 57, 63, and 90 deg. The extrusion container was fitted with a heating element and controller permitting temperatures up to 600°C to be maintained within i5"C. Extrusion was performed at 250°, 300°, 350°, 400°, and 500°C at constant speed (approximately 1 mm per sec) and constant die reduction. The extrusion product was a wire 1 mm in diam and approximately 20 cm long. In order to remove the surface layer with the "conical" texture and to reduce the absorption by the X-ray examination of the samples, the extruded wire was etched to 0.22 mm in diam. Experiments were performed in the middle sections of the 20-cm-long wires. In addition to the die of l-mm hole diam, dies with a 1.5-, 0.7-, 0.6-, 0.5-, and 0.4-mm hole diam and 63-deg die angle were constructed. In our experiments we did not find in these ranges any important difference concerning the texture of the extruded wires and we continued our work solely on the 1.0-mm die. The diffracted X-rays (Cu K radiation) were recorded photographically. Diffracted intensities were measured on the (111) reflection with a microphotometer. The relative amounts of texture components were determined from the areas under the diffracted maxima. We found the texture of extruded aluminum wires to be strongly influenced not only by the temperature of extrusion and the purity of the sample but also by the form of the die. It is generally admitted that cold-drawn aluminum wires have mainly a (111) texture with a small amount of (001) component, Table I of Ref. 1. In our experiments with wires extruded in conditions represented by Fig. 1, in some cases a single (001) texture was obtained. If these wires were drawn repeatedly at room temperature, X-ray measurements revealed a duplex (001)-(111) fiber texture. Further drawings increased the (111) and decreased the (001) texture component. In Fig. 1 the percentage of material oriented with (001) parallel to the extrusion direction is represented as a function of the temperature and the die angle (a), for commercial and refined aluminum samples, respectively. From these diagrams we may draw the following conclusions. The slope of the die (a) influenced more strongly the texture at the lower rather than the higher temperatures. Again, a stronger influence was found in the case of the commercial in comparison with refined aluminum samples. In the case of the commercial aluminum samples the amount of material with (001) texture increases with increasing wire temperature in an approximately linear manner. This effect is less pronounced in the pure aluminum samples, with the exception of the die with a = 45 deg. In this case the (001) texture decreases with increasing temperature, as shown in Fig. 1. Component (001) is more pronounced in higher-purity aluminum samples. Our experiments led to the conclusion that both (001) and (111) components are essentially stable in extruded aluminum wires. As we obtained a single (001) texture starting with a sample of drawn wire in which the (001) component was very weak, our experiments revealed that the (001) component is not a remnant of the initial texture; this is in disagreement with the findings of Vandermeer and McHargue.1 We gratefully acknowledge discussions with Professor M. Paic. 1 R. A. Vandermeer and C. J. McHargue: Trans. 7MS-AME, 1964, vol. 230, p. 667.

Jan 1, 1969

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific- indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1971 at 5 million tons valued at $200 million, averaging $40.00 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, calcium carbonate, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface smoothness, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. The chart in Table 1, updated from the 3rd edition of Industrial Rocks and Minerals, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses.

Jan 1, 1975

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By Elmer R. Kaiser

Industry Adopts Research: Seventy-Ave years ago Thomas A. Edison began in a modest way and with limited funds to gather about him men of various talents to form the first industrial research laboratory. His laboratory at Menlo Park, N. J., became famous for many discoveries and inventions, but possibly the most important of all may yet be the industrial research laboratory itself. Today, private industry operates 2500 research laboratories in which 135,000 persons' are directly and indirectly creating new processes and products and improving old ones, as well as developing new information to help keep the fountain of knowledge from running dry. In this change-making function, the scientific personnel comprises 41 pct; the technical personnel 26 pct; and the balance, 33 pct, nontechnical. The term "industrial research" has become so broad as to include almost everything beginning with the search for and discovery of the laws governing the properties of matter and energy to the development and testing of processes, methods, and equipment. These classes of investigation commonly merge so that no sharp boundary can be traced between them. The National Research Council therefore defines industrial research as "the endeavor to learn how to apply scientific facts to the service of mankind."' Currently, expenditures for research by industry are variously estimated at between $450,000,000 to $700,000,000 a year,' or about twice the expenditure for 1940. The President's Scientific Research Board" estimated that the national research and development for 1947 (excluding atomic energy) was as follows: A few companies spend as much as 5 pct of their gross receipts for research, but 1% to 2 pct is considered a good proportion by many." Shortages: Commendable as is the record of growth and accomplishment of science in industry, it is only a beginning. America and the rest of the world have merely sampled the fruits of industrial research; most industries have yet to make research the key to their future. A top research consultant, T. A. Boyd, of General Motors, states ". . . perhaps 90 per cent of all companies still have no research laboratories."Y or example, of more than 17,000 manufacturing concerns whose gross sales exceed $500,000 a year, less than 2500 have research laboratories. A still smaller proportion of the 184,230 manufacturing establishments in 161 industriese have or could afford their own research facilities. Yet, the small and mediurn-sized com,panies with less than 250 employees each, produce one half of the dollar volume of manufactured products.' How are these companies to participate in and share the benefits of research? Boyd gives two reasons for the inadequate number of laboratories in industry: Many people still do not appreciate the importance of research, nor understand its tremendous potentiali-

Jan 1, 1951

By Elmer R. Kaiser

Industry Adopts Research: Seventy-Ave years ago Thomas A. Edison began in a modest way and with limited funds to gather about him men of various talents to form the first industrial research laboratory. His laboratory at Menlo Park, N. J., became famous for many discoveries and inventions, but possibly the most important of all may yet be the industrial research laboratory itself. Today, private industry operates 2500 research laboratories in which 135,000 persons' are directly and indirectly creating new processes and products and improving old ones, as well as developing new information to help keep the fountain of knowledge from running dry. In this change-making function, the scientific personnel comprises 41 pct; the technical personnel 26 pct; and the balance, 33 pct, nontechnical. The term "industrial research" has become so broad as to include almost everything beginning with the search for and discovery of the laws governing the properties of matter and energy to the development and testing of processes, methods, and equipment. These classes of investigation commonly merge so that no sharp boundary can be traced between them. The National Research Council therefore defines industrial research as "the endeavor to learn how to apply scientific facts to the service of mankind."' Currently, expenditures for research by industry are variously estimated at between $450,000,000 to $700,000,000 a year,' or about twice the expenditure for 1940. The President's Scientific Research Board" estimated that the national research and development for 1947 (excluding atomic energy) was as follows: A few companies spend as much as 5 pct of their gross receipts for research, but 1% to 2 pct is considered a good proportion by many." Shortages: Commendable as is the record of growth and accomplishment of science in industry, it is only a beginning. America and the rest of the world have merely sampled the fruits of industrial research; most industries have yet to make research the key to their future. A top research consultant, T. A. Boyd, of General Motors, states ". . . perhaps 90 per cent of all companies still have no research laboratories."Y or example, of more than 17,000 manufacturing concerns whose gross sales exceed $500,000 a year, less than 2500 have research laboratories. A still smaller proportion of the 184,230 manufacturing establishments in 161 industriese have or could afford their own research facilities. Yet, the small and mediurn-sized com,panies with less than 250 employees each, produce one half of the dollar volume of manufactured products.' How are these companies to participate in and share the benefits of research? Boyd gives two reasons for the inadequate number of laboratories in industry: Many people still do not appreciate the importance of research, nor understand its tremendous potentiali-

Jan 1, 1951

By AIME AIME

SECOND only to the February Annual Meeting of the Institute are the Regional and Divisional meetings held in the fall of each year. Six such gatherings are scheduled in the next the months, with something likely to interest every member of the Institute. A brief résumé of the programs follows. Regional Meeting Vancouver T HE regional meeting of the Institute will be held at Vancouver, Sept. 13 to 20, in conjunction with the annual western meeting of the Canadian Institute of Mining and Metallurgy. The pro gram appeared on page 350 of MINING AND METALLURGY for July and-proof of careful preparation-a month later re- quires no correction and little elaboration. On the technical side there are few changes. A new item on the Wednesday morning program is the paper, "Investigation of Residential-type Stokers," by H. F. Yancey, supervising engineer, Northwest Experiment Station. U. S. Bureau of Mines, Seattle. As to entertainment the meeting is taking on some most pleasurable aspects. Two notable excursions have been arranged.

Jan 1, 1937

By Robert E. Wilson

TO show the vital importance of our future oil supplies to our economy, I will merely point out that this country, with something like 15 per cent of the world's land area and something like 7 per cent of the world's population normally uses between 65 and 70 per cent of the motor vehicles of the world, between 65 and 70 per cent of the world's rubber, and produces and refines between 65 and 70 per cent of the world's petroleum. Despite all the arguments as to which is cause and which is effect, all will agree that all three of these important industries are mutually dependent. If we had not been able to produce 65 or 70 per cent of the world's oil in this country we would not have the degree of mechanization, or the efficiency of transportation, or the high industrialization that we enjoy. Furthermore, the fact that oil has been plentiful and cheap has had a tremendous effect on all the things in which we as engineers are interested. For that reason, if for no other, it is well to look ahead to see what the outlook is for the near and far-distant future.

Jan 1, 1945