Search Documents

By Raymond L. Jones

With the inauguration of open-pit copper mining in Bagdad, Ariz., plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until spring 1961.

Jan 9, 1977

By Arthur H. Wilson

INTRODUCTION The stratified deposits of the coal measures are strongly laminated and exhibit a high degree of anisotropy. The stronger rocks in the sequence possess joints and shear planes, the coal itself has a closely spaced cleat pattern, and the softer rocks are capable of flowage. To calculate the general distribution of stress in such a medium by analytical means based on the theories of elasticity is difficult, and has not yet been satisfactorily achieved. Nevertheless, some estimate is required to aid the design of supporting pillars and permit the correct siting of main roadways. This is important when laying out districts for longwall extraction, particularly if the results of previous experience are not available in the area to be exploited. Although elastic stress analyses, including finite element analysis, may not be very appropriate, the basic equilibrium conditions will apply. These, combined with logical deductions based on observed fact, can be used to give appropriate solutions which experience has shown to be capable of giving acceptable results in the design of pillars associated with longwall workings. Constancy of cover load is one of the fundamental equilibrium conditions. When mining below ground, the cover is not removed, therefore the average vertical load after mining must equal the initial cover load. If mining produces a local decrease in load in any particular area, it must be balanced by an equivalent increase in load nearby. Bending moments in the strata above are capable of compensating for the turning moments which this redistribution of load may produce, and the existence of a "rear abutment", much discussed between 1950 and 1960, is not an essential equilibrium requirement. If the distribution of vertical stress is plotted three-dimensionally, then the load on any small element of area 6S will be o.6S, where o is the average stress. This also represents the volume of the "stress envelope" which lies above 6s. By making the individual areas very small and summing together, it is possible to show that the total load on any particular area can be found by calculating the volume of the stress distribution envelope which lies above it. A similar consideration applies to the stress distribution in a two-dimensional situation. If the stress distribution curve is drawn, then the area below any portion will represent the load per unit depth of section. For example, Figure 1 represents the possible stress distribution across a caved waste and associated ribside. If AW is the load deficiency [ ] These loads must balance, therefore area AW = AS, and if one can be deduced, the other will then be known. Attempts have been made to measure stress distributions in the ribside and in the waste. Stress meters in soft rocks such as the coal measures have not proved very effective. Those based on the measurement of strain have experienced difficulty in strata capable of flowage, high modulus stress meters suffer from cross sensitivity, and overcoming to obtain absolute stress is almost impossible. Load measuring instruments left in the waste have also proved largely ineffective, mainly as a result of the difficulties of protecting the leads in a caving environment. Certain logical deductions, however, can be made about the conditions in the waste. CONDITIONS IN THE WASTE Over the area of the waste the surface trough which develops is remarkably consistent, despite the geological variations which occur from coalfield to coalfield. In Britain, an accuracy of 210% is claimed for subsidence prediction based on width of extraction and depth of cover (National Coal Board, 1975). The subsidence in the USA is more variable (Adamek and Jeran, 1981), particularly with respect to the point of inflexion, but the same general pattern occurs. At the shallower depths the somewhat harder roof strata involved in the caving in the USA may suffer less compaction, giving reduced values of subsidence. Subsidence at intermediate horizons below the surface

Jan 1, 1982

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By J. E. Johnson

(Cleveland Meeting, October, 11,1912.) THE subject of blast-furnace slag is one which has had much consideration, particularly from the scientific standpoint, and several years ago technical literature contained many learned discussions on the oxygen-ratio of the acids and the bases, all on the assumption that acids and bases must be present in a ratio depending on molecular weight and chemical valency. Much work has also been done, sometimes in conjunction with the former, on the total heat and the temperature of initial fusion or softening of various slags. A wider knowledge of the blast-furnace now enables us to say that for practical purposes this work has been of almost no value. It is now generally admitted that on the physical side the important point of a given slag is neither its total heat of fusion nor its softening-point, but its free-running temperature, since this is the critical temperature of the furnace. This temperature bears no definite relation to the softening-temperature, as determined by Seger cones, for instance, because some slags melt relatively like ice, with a very short viscous-range, while others melt relatively like tar, with a very long viscous-range. In one the difference between the softening- and the free-running temperature may be very small, as little as 100° F., while in another this difference may easily be 200° or 300°. The importance of this difference is so great in practice as to destroy completely the value of exhaustive investigations, even such as those of 0. Boudouard, published a few years ago.1 * Presented also at the Joint Meeting of the Institute with Section IIIa, Metallurgy and Mining, of the Eighth International Congress of Applied Chemistry, New York, September, 1912. 1 It may not be amiss at this point to call attention to the excellent suggestion of Woolsey McA. Johnson, made several years ago, for determining the temperature at which different slags have the same practical fusibility. This suggestion

Oct 1, 1912

By Lucius W. Mayer

WHILE the mind of the financier does not normally run along channels similar to those of his technical adviser, engineers, because of their exactness, are ever more called upon to manage affairs where financial matters are involved. It is, true, not a relatively large number have thus far functioned in this capacity. It is also true that the essentially financial mind could not serve in a responsible engineering position; for to be a successful engineer one requires precise thinking, making due allowance for factors of safety. To be a financier seems to require less aptitude for exact thinking than of enthusiasm and confidence in capitalizing prospective possibilities. Both require imagination, the engineer being, more conscious of the limitations of natural conditions. It is to be regretted that the engineer' stands so far aloof from financial matters. Many consider them- selves successful, as did Steinmetz, as long as their reward is the consciousness that they are giving supreme service to mankind. They are 'generally happy in their work and, like our honored brothers who are teachers, gain their greatest satisfaction, not in the amount of their remuneration so much as in the service rendered society and in the excellence of results achieved. Indeed, these sentiments bespeak character and command respect.

Jan 1, 1924

By W. L. Saunders

(New Haven Meeting, February, 1909.) This paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the heading-and-bench system. Much de-pends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading. In mines, the tunnels, drifts, cross-cuts, adits, etc., are usually of small diameter, hence the driving of headings applies to completed tunnels in minim-work, except, of course, in cases like drainage-tunnels and main entries leading into coal-mines, where conditions call for tunnels of large diameter, approximating those driven for railway-service. In building aqueducts the tunnels are driven from 6 to 8 ft. in diameter up to 15 or 20 ft., while in railway-service the dimensions vary from 18 to 30 ft. in diameter. There is no department of rock-excavation so difficult as that of heading-driving. This work. also belongs to the most expensive class in rock-excavation. A heading is driven .directly in the solid. There are no lines of lesser resistance towards which to direct the energy of the blast, but. the material must be blown out by main force. The completion of the heading simplifies all the rest of the work of excavation. It is easy, for instance, to enlarge a heading either from above, below or oil the sides, by breaking towards the open face through holes approximately at right angles to the axis of the heading; or the enlargement sometimes takes place by holes driven outside

Apr 1, 1909

By W. J. Keep

We have shown in former papers the influence which aluminum exerts when added to cast-iron, and we have presented in another paper, accompanying this one, the physical properties of the metal aluminum and of some of its alloys. The present paper continues the investigation. The reader will find, in our paper on "Aluminum and Other Metals Compared,"* explanations not here repeated, which will render the diagrams in this paper intelligible. The scale of stresses is laid off on the ordinate which rises from the zero-point of the diagram. The scale of deflections is laid off on the abscissa which runs horizontally through this zero-point. By applying a given amount of stress, then running back to zero, and again applying the same stress, we describe a spring-line, in which the deflections are proportional to the stresses. Generally the deflections exceed this proportion during the original application of stress; and the excess is the permanent set. By laying off from the zero-point a line parallel to the springline, we shall generally find that this new spring-line and the diagram coincide for some distance; that is, that the test-bar is

Jan 1, 1890

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared for these tests by high-temperature methods, especially by crystallization from borax melts.

Jan 1, 1950

By J. Chupak, D. J. Salley, G. L. Simard

Radiotracers were demonstrated to be of considerable value in a study of the interaction of dithiophosphate with galena. The interaction had characteristics of both chemisorption and chemical reaction, being complex because of the nature of the galena surface. Sorption was rapid and markedly reversible, and flotation occurred at relatively small amounts of dithiophosphate sorbed.

Jan 1, 1950

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,' little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district. The recognition of alteration phenomena and related features by Hoyt S. Gale3 in 1935, followed by the work of Shenon and McConnel in 1936-37,4 changed many of the concepts formerly held and opened the way for more critical study and mapping of alteration effects. Mapping of these effects has been in progress for several years but no well-organized, careful, and complete laboratory study of the alteration has been made by mining companies or by government agencies. Recently, Thomas Mitcham of Columbia University has been occupied in the collection and study of specimens carefully selected from several producing mines in the Silver Belt as well as from several prospects exhibiting alteration effects. Mr. Mitcham and the writer have discussed some of the preliminary results of his investigations, which indicate that definite and interesting material is forthcoming from his studies. Work of this kind, aided by careful observation by district geologists, should advance the knowledge of the environment of Silver Belt ore shoots and establish additional criteria for recognizing meager shallow expressions of deep-lying orebodies. Structural details in the Silver Belt area are extremely difficult to decipher on the surface because the area is almost completely covered by a deep mantle of surface debris and soil. A dense growth of small trees and buck brush adds to a geologist's difficulties. Often large areas reveal only scattered small outcrops with great intervening areas where the underlying formations must be deduced from small altered rock fragments. Some considerable success in obtaining surface information has come from bulldozer roads and cuts in selected areas. As this type of work receives more attention, knowledge of the surface expressions of formations, alterations, faulting, and veining is expanding and giving more reliable information to guide deeper development. Lack of diagnostic marker beds in the district contributes to a geologist's difficulties in determining fault displacements. In the Silver Belt, known commercally important sulphide orebodies commonly are associated with siderite and quartz gangue. Some of the veins at shallow horizons above productive ore shoots are composed of quartz with light-colored carbonate minerals such as calcite, ferrocalcite, ferrodolomite, ankerite, and carbonates with variable amounts of manganese. The relation of these carbonates to commercial orebodies is a problem offering possibilities for research. Shallow exposures of veins composed of quartz and the light-colored carbonates, often with some associated barite, grade into quartz and siderite veins at deeper horizons. The vertical range of these carbonates has been partially established for some veins, but no reliable method has been devised for predicting where the change in a vein may take place. Careful observation and analysis of carbonates may make it possible to predict more closely where the change to siderite may be expected. In 1926 Shannon5 pointed out some of the characteristics of the carbonate veins of the district and included a few chemical analyses. Some of the Silver Belt ore shoots have small commercial outcrops, and very shallow development of some properties has led to the opening of small ore shoots." Several small ore shoots developed at shallow depths have not been explored at deep horizons, and some important ore shoots with no commercially significant exposures at shallow horizons have been developed. The greatest problem of the mining geologist working in the Silver Belt area is to find the all-important link between the very meager shallow expressions of mineralization and the rich ore shoots that may be found below. To develop criteria for use in the recognition of the weak upper expression of ore shoots, the experience of past development programs must be relied upon heavily. The investment of more than a million dollars in the exploration for such ore shoots requires some reliable criteria if these ore shoots are to be found. Management needs some assurance that the risk involved is justified by well-developed and acceptable geological inference. The richness of some of the ore shoots found thus far has contributed greatly to the justification for a bold approach, but many negative results of blind exploration programs would lead eventually to extreme caution on the part of management. Fortunately, recent experiences of development programs have been quite successful. It is hoped that added knowledge. of the environment of Silver Belt ore shoots will contribute greatly to the sureness of approach toward their development. The Coeur d'Alene mining district is located in the panhandle of Idaho in Shoshone County. The population of the county is either employed in the

Jan 1, 1952

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as 'could be expected without railroad transportation

Jan 1, 1924

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

By Wendell S. Williams

Single crystals of TIC doped with boron at high temperat~ires develop second-phase inclusions. The inclusions are in the form of lamellae lying parallel to {l 11 } planes of the Tic matrix and can be vevealed by etching [100] cleavage faces of the boron-doped Tic crystals. measurements of the critical resolved shear stress. t, of TIC crystals containing such inclusions showed that the ropid drop in t wilh increasing temperatu.ve found for pure Tic was greatly reduced. At 1600°C, the inclusion containing crystals had a value of t five limes that of pure Tic. The hardening effect also was found to inhibit hot pressing of TiC powders containing boron impurity. Thermochemical and crys-tallographic arguments suggest that the inclusions are TiB2. The boron content of the hardened carbide is a few tenths of 1 pct. TITANIUM carbide is noted for its high room-temperature hardness. However, measurements of the critical resolved shear stress, T, of single crystals of Tic at high temperatures have shown that t decreases exponentially with increasing temperature.' This temperature dependence of t is attributed to thermally activated dislocation mobility limited by a large Peierls stress.' In turn, this large Peierls stress is believed to be a consequence of strong co-valent and ionic binding in Tic. The rapid drop in 7 with increasing temperature, characteristic of pure Tic, is lessened by the introduction of second-phase inclusions. Exposure of Tic to boron at high temperatures produces such inclusions. A report of the influence of boron on t in Tic is presented, followed by a discussion of the nature and formation of boron-containing inclusions in Tic which are believed to be responsible for the hardening effect. I) CRITICAL RESOLVED SHEAR STRESS OF BORON-DOPED Tic CRYSTALS Tic single crystal boules grown by Union Carbide Corp., Linde Division, were doped with boron by placing them in a carbon crucible packed with boron powder and heating in a vacuum furnace to 2000°C for 1 hr. Samples 1 by 1 by 3 mm were cleaved from these doped boules. High-temperature compression tests' were made on these samples to determine the critical resolved shear stress as a function of temperature . The rapid drop in critical resolved shear stress found for pure Tic crystals' did not occur: tests indicated that the boron-doped crystals at 1600°C had values of T equal to those of pure Tic crystals heated to only 1100°C, Fig. 1. No difference in the shape of the individual stress-strain curves was produced by the boron doping, but the stress scale was multiplied by a large factor. The hardening effect of boron in Tic probably extends to temperatures lower than those used in the present work (1100°C minimum). At room temperature, however, the influence of boron is difficult to determine because the stress required for gross plastic flow in pure Tic is SO high that in practice fracture cccurs first. Microhardness is the only test that can give an indication of the yield stress in Tic at room temperature. such measurements were made5 on boron-doped Tic; the matrix had a hardness value

Jan 1, 1967

By J. C. Wilhoit, J. B. Cheatham

Although an oil well is a long cylindrical hole with an irregular bottom, it appears likely that the nature of the stress concentration at the bottom of the hole can be ascertained from an analysis of the stresses around a short cylindrical cavity with rounded comers and smooth bottom. Such a cavity is studied primarily because it leads more readily to a solution to the problem by the use of stress functions. In this paper the stress distribution around a short cylindrical cavity subjected to bit loading, overburden and drilling-fluid pressures is determined by means of an analytical solution which approximately satisfies the boundary conditions of the problem. From this solution the stresses at the corner of the hole are calculated to be about 35 per cent lower than comparable results obtained by photoelastic and relaxation analyses. This difference is apparently due to the large radius of curvature at the corner of the cavity in the present analysis. Since good agreement is obtained between the results of this analysis and the stresses calculated for a similar loading on a semi-infinite elastic solid, it is concluded that the bit action in the region near the center of the hole is not appreciably affected by the presence of the sides of the hole. INTRODUCTION Much has been written concerning drilling "under down-hole conditions" and pertaining to the stress distribution in the rock at the bottom of an oil well.1-5 For example, it is known that identical rocks can be drilled more rapidly at the surface than under subsurface conditions of pressure and stress.6 Information on the behavior of rocks under loading can be obtained from triaxial test data.7-9 From such tests it is found that rocks exhibit brittle failure when the confining pressure and pore pressure are equal, but the mode of failure may change to ductile as the difference between the confining pressure and the pore pressure is increased. Brittle failure implies that there is very little permanent deformation before fracture, whereas ductile failure indicates that permanent deformation takes place before fracture. Some rocks are ductile at differential pressures of 5,000 psi , but other rocks are brittle even at differential pressures of more than 50,000 psi. Cuttings embedded in mud at the bottom of the hole may act as a plastic mass which the bit teeth must penetrate in order to attack the virgin rock below. 10 During drilling, the mud pressure acts as the confing pressure, and in many cases the difference between the mud pressure and the formation pore pressure IS sufficiently low so that the rock most likely falls in a brittle manner. Very little penetratiori by the bit teeth may be required for brittle failure of the rock. For these brittle materials, the elastic stress distribution is of practical interest in determicing the possible effects of a given loading on failure. The penetration of bit teeth into ductile or plastic rock has been analyzed previously ll,12 and will not be considered further in the present work. During actual drilling, many teeth act at various points ovel an irregular hole bottom. In the present analysis a solution is obtained for an idealized problem of determining the elastic stress distribution caused by only one tooth acting alone at the center of a smooth hole bottom. It obviously is not proposed that any driller should put a special one-tooth bit on bottom, but it is hoped that extensions of the simpler problems can eventually lead to a better understanding of more complex actual drilling phenomena. To obtain a solution by the use of stress functions, a short cylindrical cavity with rounded corners and smooth bottom is studied. The solution to this problem should give an insight into the nature of the stress concentration at the bottom of an oil well which is in reality a long cylindrical hole with an irregularr bottom. After selection of the proper curvilinear co-ordinate system, the stress functions are expressed as series of Legendre polynomials. The coefficient of each term in the series is then determined to satisfy the boundary conditions at a finite number of discrete points on the boundary of the cavity with least square error. Results are compared with bottom-hole stresses obtained by photoelastic and relaxation analyses.

By J. R. Hauber, N. R. Borch

A study uras made on the creep behavior of cast and extruded SR grade beryllium. It is shown that, for stresses below about 1000 psi in the temperature range 760" to 85o° c, the creep behatior is nearly exactly described by the Nabarro-Herring mechanism. The activation energy is apparently that for self-diffusion, 42 2 kcal per mole, below 1000 psi, but it rises to 88.6' kcal per mole at higher stresses. The slress exponent is 4.5 at the higher stresses. Tertiary creep in this material is clearly related to void formation apparently caused by grain boundary sliding. BERYLLIUM is becoming an increasingly important technological material. A search of the literature has revealed a lack of fundamental studies on the creep of beryllium. This investigation was therefore undertaken to gain insight into the creep behavior of this material. EXPERIMENTAL PROCEDURE Tensile creep samples were prepared from cast and extruded SR grade beryllium. The vendor's chemical analysis of the beryllium tested is shown in Table I. The test specimens were machined as shown in Fig. 1 from i -in.-diam rods. The machined creep specimens were annealed to remove surface damage and to establish a variation in grain size. The heat treatments and their resulting grain diameters are shown in Table 11. The average grain diameters were determined by the intercept method. True average grain diameters were estimated by multiplying the measured average grain diameters by 1.5.' The creep tests were performed at temperatures from 700" to 850°C in a vacuum of 105 Torr or better in a tantalum-element resistance furnace. Loads were applied by an Instron testing machine such that the stress was held constant to within 20 psi. The test temperature was measured by thermocouples on the sample. With one exception the deviation from the desired test temperature was 2"C, and in that case the deviation was 4"C. Elongations were measured by an extensometer within the vacuum chamber which was fastened to the creep specimens at the grooves in the grip ends, as shown in Fig. 1. The precision of measurement of elongation was 1 X loe4 in. The creep tests were begun only after thermal equilibrium had been established in the sample and the extensometer to insure that there was no strain rate component due to transient thermal effects. Two kinds of creep experiments were performed. First, at constant grain size, the effects of varying stress and temperature were studied. In the second set of experiments, the temperature was held constant and the grain size was varied. The activation energy for creep was determined by varying the temperature at constant stress, as described by orn, during the first set of experiments. The variable grain size experiments revealed that creep at low stress apparently occurred by the abarro-errin' mechanism. In all of the creep tests, the stress was held constant only until sufficient strain had occurred to accurately determine the creep rate. The stress was then raised to a new value and the new creep rate determined. This process was reported until tertiary creep occurred. In this manner several data points were obtained from each specimen. The assumption was made that the structure was not changing appreciably between the incremental stress levels. This was verified by reducing stresses to previously tested levels and comparing the creep rates with the creep rates obtained at the lower strains. The re-producibility was within experimental error over strains on the order of 1 pct. EXPERIMENTAL RESULTS A typical series of creep tests is shown in Fig. 2. Primary creep was not observed in any test. Transient creep, which we define as creep rates that are nonlinear with time, was not observed for any change in stress except where tertiary creep occurred. The absence of both primary and transient creep has been previously reported for hot-pressed powder beryllium.= The data for the creep behavior at constant grain size are summarized in Fig. 3. The data show two distinctly different stress dependencies. At stresses below about 1000 psi, in the equation:

Jan 1, 1969

By K. Tangri, B. Swaroop

Simultaneous measurements of lattice (elastic) strain by X-ray line shift method and total strain with an electrical strain gage have been carried out on polycrystalli,ne nickel with the help of a specially designed tensometer attachment for the X-ray dif-fractometer. During the initial stages of deformation, the rate of increase in lattice strain closely follows the total strain until the plastic strain sets in. From then onwards, the two strains deviate from each other and with further increase in afiplied stress the rate of increase of lattice strain eventually decreases. Depending upon the mode of unloading, both compressive and tensile strains have been observed in nickel deformed up to 0.29 pct strain. These results have been explained on the basis of the effects of clustering of dislocations and also the production and behavior of point defects during loading and unloading, respectively. POLYCRYSTALS deformed plastically in a uniaxial tension test show residual lattice strains (hereafter referred to as RLS), which broaden the X-ray line profiles and shift their peak positions.''4 It is known that uniform straining of a crystal lattice (macrostrain) produced movement of ddfraction line peaks, whereas nonuniform straining (microstrain) causes line broadening.= Though the nature and origin of RLS in deformed metals is not yet clearly understood, these are believed to be due to the presence of some form of a locked-up stress system. Several possible detailed interpretations6'" of the stress system have been proposed by various workers and common to all these interpretations is the assumption that different parts of the aggregate have different tensile yield stresses; e.g., that a part A yields under a lower applied stress than a part B. Therefore, during the deformation process, the elastic strain in A will be less than that in B, and, after completion of deformation, B will tend to contract further than A but will be prevented from doing so by the restraining influence of A. Thus, when equilibrium is reached, A will be in compression while B is in tension. Although there is general agreement on the correctness of this argument, controversy still exists as to the exact nature of the parts A and B in a deformed metal. In an alternative approach to the creation of parts A and B, many other investigators have assumed that the RLS observed in unloaded specimens are in some way connected with the lack of proportionality between lattice strain and applied stress in the region above the yield stress." cullity13 has prepared a schematic summary of the results of previous workers, mainly Smith and Wood,2'11 which suggests that, above the elastic limit, the lattice strain may increase less rapidly with respect to strain, or may even decrease with increase in applied stress. If the applied stress is then decreased, the lattice strain would decrease along a line parallel to the loading line in the elastic region and thus produce a compressive residual lattice strain after unloading. At equilibrium, to balance these compressive stresses? there would have to be regions under tensile stress which may well be the grain boundaries or the substructure walls formed during deformation. The present investigation was undertaken to gain a better understanding of the nature and origin of RLS and also to experimentally verify the salient features of this hypothesis. EXPERIMENTAL Stress and strain determinations were made with a specially constructed tensometer attachment for the X-ray diffractometer, Fig. 1: which permits the following measurements simultaneously on a sheet specimen under uniaxial tension at various stress levels during loading and unloading: a) lattice strains, E=. in a direction perpendicular to the direction of pulling (x direction) from shifts in X-ray line peak positions; b) the total strain, ex, in the direction of pulling. with the help of an electrical strain gage affixed to the back of the specimen directly below the area irradiated by X-rays: and c) the applied stress, with the help of a load cell which consisted of a calibrated stainless-steel sample of dimensions identical to those of the specimen under investigation, and to which it was coupled. Because of its high stacking fault energy.I4 nickel

Jan 1, 1970

By P. A. Witherspoon, Y. W. Tsang

Normal stress-fracture closure variation and stress-dependent fluid flow rates were calculated for rock fractures of different aperture distributions. This study shows that both the mechanical and hydraulic properties of the fracture are controlled by the large-scale roughness of the rock fracture. Hence the typical large-scale undulation wavelength of the rock joint dictates the suitable sample size to be used in normal stress and fluid-flow measurements, if results due purely to sample size are to be avoided.

Jan 1, 1982

By J. F. Wolff

CARL ZAPFFE, Brainerd, Minn. (communication to the Secretary*).¬Unless one has actually directed explorations for iron ore, it is doubtful whether the importance of Mr. Wolff's paper, the value of the information contained, and the large amount of detail work involved in what is set forth can be fully appreciated. It is indeed rare to get such a com-

Jan 3, 1917

Jan 1, 1924