Search Documents

By E. S. Machlin

The possibility that formation of voids under creep-rupture conditions may take place by the condensation of vacancies has been investigated theoretically. It has been concluded that nucleation of voids under creep-rupture conditions by vacancy condensation is highly improbable. However, growth of pre-existant voids by vacancy condensation is probable. A number of predictions made in this theory have been verified by the data. It has been predicted and checked that the product of rupture life and steady-state creep rate for preannealed metals and single phase alloys is an approximately invariant quantity, independent of stress, temperature, and atomic number for a given type structure. The direction of the effect of cold work on this product has been predicted and found in agreement with experiment. A number of experiments to evaluate the vacancy condensation mechanism further are described. SEVERAL papers have appeared recently which speculate on the origin of voids formed at grain boundaries under stress.' ' The object of this paper is to examine quantitatively the proposition that the voids produced in a creep test are a result of vacancy condensation. A result of this paper is a theory of creep-rupture. Void Nucleation Application of standard nucleation theory" to the problem of void nucleation leads to the following conclusions: 1—Homogeneous nucleation of voids requires a supersaturation ratio (concentration of vacancies in supersaturated to that in saturated solution) of 400 for a reasonable surface energy of 1000 erg per cm-and 1.4 for the improbably low surface energy of 10 erg per cm. 2—Heterogeneous nucleation of voids at plane interfaces between two phases requires a supersaturation ratio of 2.5 for a typical contact angle of 145 3-—Void nucleation about a solid particle may be accomplished at a supersaturation ratio of 1.17 for a typical value of work of adhesion? of 60 erg per The work of adhesion is the surface work 10 replace two solid-vauor surfaces by a solid-solid interface. enr ' between an oxide and a metal in the presence of a surface active element such as sulphur. Estimates of the supersaturation ratio at which voids are produced in diffusion experiments yield a maximum of 1.01. Inasmuch as the foregoing mechanisms of void nucleation probably will not operate at this level—too low a surface energy is required—the investigatol. is led to the conclusion that voids must already exist. That is, nucleation of voids probably does not occur. Rather, existing submicroscopic voids grow out to visible size. Already existing voids might be produced during solidification or working. Supercritical sized parlicles which contain cracks may act as heterogeneous void nuclei. Gas pockets may act as void nuclei. Experiments are desired to determine the nature of the heterogeneous void nuclei which grow out to voids in both diffusion and creep experiments. Void Growth Void growth might occur in at least two possible ways, depending upon whether the already existing void nuclei are at grain boundaries or within the grains. In the case of a spherical void far from a crystal boundary, vacancies are generated during creep as a consequence of the migration of suitable dislocation jogs' and are also annihilated at sinks. Under these conditions, a steady-state concentration of vacancies is built up in the crystal, defined by the condition that for any differential volume the rate of generation of vacancies in that volume equals the rate of annihilation of those vacancies." This equality would lead to the development of a gradient of vacancy concentration radially outward from the void surface up to a radius where the vacancy lifetime becomes equal for all directions of vacancy migration. The distance over which this vacancy concentration gradient extends equals about 2vD,T* where D, is the vacancy diffusivity and T:' the vacancy lifetime in a crystal outside the gradient in a zone of constant vacancy concentration. The vacancies generated in the region over which the gradient exists will annihilate more often at the void than elsewhere. Approximately a little over one-half the vacancies generated in the gradient zone will annihilate at the void. Hence, the growth rate of the void is given by on where R is the radius of void in centimeters, is the atomic volume, and R is the rate of generation of vacancies, number per centimeter" per second. R D and T* may be estimated in terms of other physical parameters." In particular, R = n.j e/b [3] where n is the average number of vacancy produc-

Jan 1, 1957

By S. Saito, P. A. Beck

The crystal structure of MoNi3 was determined by means of X-ray diffraction. This structure is isotype with that of ovgered TiCu3. The lattice parameters are: a. = 5.064A, bo = 4.224A, co = 4.448A, and zf 0.157. If the orthorhombic distortion (slight relative to the corresponding orthohexagonal unit cell) is disregarded, the structure may be described in terms of a close-packed ordered atomic layer, stacked in the sequence: abab. The structztres of ordered TiCu3 and TiAl3 are homotectic. The three types of ordered hexagonal phases, iso-structural with TiNi3, MgCd3, and VCo3, are known to occur in AB3 alloys of transition elements of the first, second, ad third long periods. It was noted1 that phases with the TiNi3 structure occur selectively in alloys of Ti-group elements with Ni-group elements. In AB3 alloys of Ti-group and V-group elements with Co-group elements the AuCu3-type structure predominates.' The vCO3 structure, which was determined very recently,' has hexagonal symmetry, but the actual atomic arrangement here, too, is rather closely related to the ordered cubic structure of AuCu3-type. However, an ordered hexagonal close-packed structure of the MgCd3-type occurs in MOCO33 and WCO3.4 Consequently, the question arises as to whether or not the crystal structure of MoNi3 is also of the MgCd3-type. Grube and winkler5 found that MoNi3 has a hexagonal close-packed structure with a = 2.54A and c/a = 1.65. They pointed out that some additional weak diffraction lines could be observed in the powder pattern, which may have been due to an ordered atomic arrangement in this phase. However, no detailed information was obtained by them and the structure was apparently not further investigated by others. The present work was, therefore, undertaken in an attempt to determine in detail the structure of MoNi3, and to investigate the possibility of ordering. EXPERIMENTAL METHODS Alloys used in the present work were arc-melted in a water-cooled copper crucible under helium atmosphere. Electrolytic nickel and molybdenum, both 99.9 pct pure, were used. Chemical analyses were not made, but the melting loss was not higher than 2 pct for any alloy. Ingots were first homogenized at 1200°C for 48hr, quenched, heavily cold worked, and then annealed at 820" or 860°C for 1 week, followed by quenching in cold water. Powder specimens for X-ray work were prepared by crushing the heat-treated solid specimens. In order to remove strains, the powders were reannealed in evacuated scaled fused silica capsules for 6 hr at the same temperature at which the corresponding solid specimens were annealed. X-ray photographs were taken with an asymmetric focussing camera, using unfiltered CrK or CuK radiation. EXPERIMENTAL RESULTS The X-ray diffraction patterns of alloys containing 20.8, 25, and 26.4 at. pct Mo, homogenized at 1200°C, showed the face-centered-cubic structure of the Ni-base a-solid solution. It was revealed, however, by micrographic examination that the 26.4 at. pct Mo alloy contained in addition very small amounts of a second phase, in accordance with the phase diagram.6 On the other hand, the 20.8 at. pct Mo alloy after annealing at 820°C gave the X-ray diffraction pattern of the ordered face-centered-tetragonal MONi4.7 In this pattern several additional weak diffraction lines were also observed, corresponding to the strongest diffraction lines of MoNi3. The alloys containing 25 and 26.4 at. pct Mo after annealing at 820" or 860°C gave X-ray diffraction patterns, as shown in Tables I and 11, corresponding to MoNi3. Each one of the reflections which could be tentatively indexed on the hexagonal close-packed cell of Grube and Winkler,5 with the exception of the basal plane reflections, was split into a doublet, as seen in Table I. Since microscopically the alloy consisted of a single phase, it seemed probable that the lattice of MoNi3 is actually slightly deformed, as compared with the tentative hexagonal unit cell. In addition to these diffraction lines, several weak lines were also present, as shown in Table 11, which could not be indexed at all on the hexagonal close-packed cell considered. Satisfactory indexing of all diffraction lines observed was found to be possible by using an orthorhombic unit cell with ao = 5.064A, ft = 4.224A, and c = 4.448A. These values, whose accuracy is estimated to approximately ± 0.008A, correspond to 95.14A3 for the volume of the unit cell, and to an X-ray density of 9.50 g per cm3. If no attention were paid to the weak reflections listed in Table II, a reduced -unit cell of half the volume (a = 2.532A, b = 4.448A, and c = 4.224A), closely related to the orthohexagonal cell, might be used. The dimensions of the orthohexagonal cell of the same volume as the reduced cell are: a = 2.562A, b = 4.437 A, and c = 4.183A. It may be seen that in the reduced cell the a axis is slightly shorter, while the b and c axes are slightly longer than those corresponding to the orthohexagonal cell of the same volume. This slight orthorhombic distortion is re-

Jan 1, 1960

By L. C. Graton

At the Tenth International Geological Congress, Mexico, 1906, Waldemar Lindgren presented "The Relation of Ore Deposition to Physical Conditions." Retrospect ranks it as the outstanding offering at that Session and as the most fundamental contribution up to that date on the philosophy of ore deposition. Elaborating thereon in his text-book "Mineral Deposits," Lindgren analyzed ore-forming processes under conditions prevailing from great depth up to surface; explained the nature of deposition in each environment; and developed a comprehensive genetic ore classification, which brought wide acceptance and enriching contributions by many. Since Lindgren's latest edition (1933), have come wealths of material relevant to ore genesis, particularly through amazing renaissance and proliferation throughout science. Current publication regarding ores now emanates largely from a generation caught in pressures of the breathless modern tempo, which tempts scant reflection upon earlier truths. Consequently, today's thrilling output contains not a few offerings that need challenge because supplanting interrelationship and system by what seems, collectively, an assemblage of strange, ad hoc and often self-contradictory concepts. From these latter some merit may eventuate but at the probable cost of present confusion and delayed progress. The following pages, naming numerous post-Lindgren advances, record the conviction, held by many, that Lindgren's philosophy, progressively improved, remains the soundest approach to understanding ore genesis.

Jan 1, 1968

By Wilson Blake

A mathematical model based on the finite element method of stress analysis has been used to describe the behavior of the western wall of the Kimbley Pit as its slope was steepened from 45° to 57°. Theoretical stress changes because of slope modification are slight except at the toe of the modified slope. Magnitudes of stress created are small when compared with the strength of a competent rock. Resulting displacement patterns point out the need for determining the in-situ state of stress at a site prior to excavation or modification. A comparison of model results with field measurements shows that, in general, the model has described the measured behavior of the west wall of the Kimbley Pit remarkably well. The Bureau of Mines and the Kennecott Copper Corp. began joint research on open-pit slope stability at the Kimbley Pit, Ely, Nev., in 1961. The initial or planning phase of this research dealt with a detailed geologic study of the Kimbley Pit, determination of in-situ stresses in the district, laboratory and field tests to determine rock properties, and the design of a full-scale experiment to study the behavior of this pit as its western wall was steepened from 45° to 57°. Fig. 1 shows a cross-section of the original pit outline, the steepened pit outline, major geologic features, and the two instrumentation adits. After the final or slope modification phase of the research began, a laboratory research program was initiated to develop a mathematical model that would analytically describe the behavior of the pit as its western slope was steepened. This theoretical model study of the slope modification at the Kimbley Pit was conducted with the finite element method of stress analysis. The results are described in this report.

Jan 1, 1969

By W. R. Hibbard, Ming-Kao Yen

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By C. A. Heiland

IN the third year of war, geophysical oil exploration broke all records to keep pace with the demand for increased reserves. Geophysical prospecting for strategic and other minerals also grew in scope. The trend of geophysical oil exploration throughout the war is indicated in Fig. 1. This figure resembles the one presented in the last annual review issue of M&M (February 1944, p. 62), corrected for data on-operations in the last months of 1943 and extended into 1944. The average number of geophysical oil prospecting crews in the field in 1944 was 451, whereas the total in 1943 was 340. An upward trend in the use of all geophysical methods is clearly evident throughout the year. Seismic operations were 67 per cent, gravimeter surveys 28 per cent, and other methods 5 per cent of the total. Seismic reflection and refraction crews increased 181/2 per cent over the 1943 average, gravimeter operations increased 73 per cent, and other methods gained 92 per cent. The increase in seismic and gravimeter operations, particularly the latter, is probably due to an increased production of equipment and the organization of new service companies. Miscellaneous methods gained largely through a revival of magnetometer work, and an increase in the use of torsion balances and electrical equipment. In comparison with the prewar average of 1941, it is noteworthy that seismic operations increased 58 per cent, gravimeter operations 88 per cent, and miscellaneous other methods gained as much as 283 per cent. Unfortunately the expansion in the number of geophysical crews does not indicate a proportionate increase in efficiency or in areal coverage, as will be brought out later.

Jan 1, 1945

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By A. A. Steel

(Spokane Meeting, September, 1909.) DURING. the summer of 1905 I was employed by the U. S. Geological Survey to investigate the geology, Mining, and preparation of barite in most. of the fields of the United States. The Eastern districts have been more or less completely described ; the Virginia field in detail by Thomas L. Watson, in his paper, Geology of the Virginia Barite-Deposits,&apos; and other fields in abstract., including statistics of production and references to current literature, by various authors .2 There have also been published a few details of the occurrence of barite in the lead-mines of Washington county, Mo.3 The other accounts of this district are erroneous and meager, and since this field is the most important one in the United States at the present time, a detailed description of the local geology seems doubly desirable. Barite-deposits are scattered over nearly the whole of Washington and adjoining counties, but. the product, is all mined from the areas indicated upon the sketch-map, Fig. 1, and is shipped from the stations of the St. Louis, Iron Mountain &. Southern railway, between Blackwell and Potosi, from 45 to 60 miles SW. of St.. Louis. The topography is for the most part gently rolling, with slightly graded streams, usually less than 200 ft. below the higher hill-tops. Along Mineral fork and Indian creek are :some steep bluffs and cliffs, affording good exposures of the

Feb 1, 1910

By K. K. Clark, W. H. Somerton

The feasibility of reducing pressures needed to fracture formations by heating the borehole intensively has been investigated on a laboratory scale. Reductions in fracture pressures of heated Bandera, Berea and Boise sandstone cores were observed at various confining pressures, simulating reservoir stress conditions to a depth of 5,000 ft. Both permeable and impermeable borehole boundary conditions were tested. Three heating conditions were used in the tests. One group of samples was heated in a furnace to a temperature of 600C, cooled to room temperature., and then tested for fracture pressures. Two other groups of samples were heated with a borehole heater to maximum borehole wall temperatures of 625 and 792C, then cooled and tested. In all cases, heated samples showed substantial reductions in fracture pressures compared to unheated samples. The higher temperature borehole heated samples showed the greatest reduction, amounting to 70 per cent in the extreme case. In actual application to wells, it was concluded that fracture pressures may be reduced by 20 to 50 per cent by intensive borehole heating before fracturing. INTRODUCTION Hydraulic fracturing of oil and gas wells is an accepted and effective technique for increasing well productivity in many areas, but is notoriously unsuccessful in other areas. The technique becomes less interesting for production stimulation purposes when excessive fracture pressures are necessary. Formations which do fracture but require high pressures, probably form horizontal fractures. There is good evidence to indicate that some formations do not fracture at all, but yield plastically under high pressure. Thus, any technique which will make formations easier to fracture or will reduce fracture pressures is potentially interesting to petroleum producers. Horizontal fractures generally occur in planes of weakness, such as bedding planes, and at pressures equaling or exceeding the effective overburden stress. In the unusual case where planes of weakness do not exist, a slightly higher pressure must be applied to overcome the tensile strength of the rock. In general, high fluid-loss fracturing fluids are conducive to the formation of horizontal fractures.1 Vertical fractures, when they do occur, are initiated at pressures generally lower than overburden pressure and are favored by low fluid-loss fracturing fluids or impermeable boreholes. The pressure necessary to create a vertical fracture in an impermeable, elastic medium can be predicted from the so-called "thick-walled cylinder" equation: Pf = 2 or+ st.............(1) where pf = fracture pressure or = radial stress st = tensile strength of medium. This equation indicates that to fracture it is necessary to overcome a tangential compressive stress, induced by and equal to two times the radial confining stress, plus the tensile strength of the medium. If the above equation held strictly true for rocks, very little could be done to reduce fracture pressure. The tensile strength of the rock might be reduced somewhat, but any change in st would be small compared to the magnitude of the tangential stress at reasonable subsurface depths. Laboratory tests have shown that actual fracture pressures exceed values predicted from Eq. 1 by factors of 1.4 to 28.6.1,2 Eq. 1 thus does not properly describe the

Jan 1, 1966

By R. H. Merrill, D. W. Wisecarver

The paper "Design of Surface and Near-Surface Construction in Rock" by Deere, Hendron, Jr., Patton, and Cording discloses a principal difference between civil and mining engineering as applied to openings in rock. Generally, the civil engineer considers an opening as an asset, where a mining engineer finds that most of his openings are a liability. The openings, or rock surfaces, treated in the paper by Deere and coauthors are designed for lasting stability and the foundations for dams, the diversion tunnels, abutments, and surface excavations are expected to be stable for long periods or provide continuous access and other useful purposes. Except for those openings used for the transportation of men, materials, ore, and for ventilation, the mining engineer finds that his underground openings serve no useful purpose once the mineralized rock has been removed. Usually, these openings create problems such as reduced ventilation efficiency, added requirements for scaling, sealing, and other tasks necessary to maintain or isolate the openings. The surface openings and mine plants present another liability to the mining engineer. After the product has been removed from the earth, the abandoned pits or strips, tailing ponds, dumps, and buildings sometimes become hazardous, unsightly, or occupy surface areas that could be used for other purposes. As a general rule, the various disciplines involved in rock mechanics have different objectives and uses for openings; however, the basic concepts regarding the design or control of openings in rock are similar for each discipline. The review by Deere and his coauthors contains examples of the duplications in this technology, and, in particular, the common approaches used by civil and mining engineers. Therefore, both the review paper and this report consider the problems that are common to most of

Jan 1, 1967

By A. E. Gorum, J. Washburn, E. R. Parker

Experimental evidence was obtained in support of the idea that cleavage fracture can be initiated by dislocation pile-up. The high ductility of MgO crystals when tested in bending comPared to their relative brittleness in tension was explained on the basis that large pile-ups are more likely in a tension specimen. CLEAVAGE fractures have been a problem of major concern for many years. A number of large steel structures have failed in a brittle manner, usually suddenly and without warning; often the failures occurred for no obvious reason and at nominal stress levels well within the generally accepted range. A great deal of data have been collected about factors that contribute to failures,1 but the physics of the fracture process has never been revealed. cottrel12 has recently developed a theory of brittle fracture in ductile materials which was based upon the concept that dislocations moving on two intersecting planes can unite to form a crack nucleus. This theory accounts for the known effect of grain size and for the effect of testing temperature. There has, as yet, been no experimental evidence published that would substantiate this or the earlier theories based on stress concentrations due to piled-up dislocations. The study reported herein was conducted to obtain information that would either substantiate or disprove the

Jan 1, 1960

By H. L. Hazen

THIS is the story of the recent operations of the Standard Cyaniding Co., which owns the Standard mine, a low-grade gold property in sight of Highway 40 about thirty miles from Lovelock toward Winnemucca, Nev. The ore is mined by power shovel and cyanided after grinding to only 3/S in. A total direct cost of $1.24 was attained in 1941 on 600 tons a day. Mining operations ceased, under Government edict, in 1942, and only in recent months have been resumed. The operating difficulties of today are: (1) the high cost of supplies; (2) labor problems; and (3) Federal laws as interpreted and enforced by executive bureaus of the Government. Of these, the increased cost of supplies is the least important.

Jan 1, 1947

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of&apos; slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964

By S. Storchheim

MORE and more attention is being paid to the bonding of metals in their solid states. For a better understanding of this technique for joining metals and how it is affected by changes in temperature, pressure, and time at temperature and pressure, a detailed report concerning nickel to aluminum bonding has been published.&apos; In order to broaden the knowledge accrued, some additional work concerning solid state joining of aluminum to copper and aluminum to zirconium was performed. The investigation of the Al-Cu system was considerably more extensive than the investigation of the Al-Zr system. For the A1-Cu system, not only were tensile sudies made but intermetallic penetration rate investigations also were carried out. The effect of temperature on intermetallic penetration rate for the A1-Cu system was determined at 11 tsi pressure, held 2 min. Procedure Apparatus: The hot pressing technique was the means of solid state reaction used and required the equipment depicted in Fig. 1. The following procedure was involved: The two metals to be reacted were placed in an aquadag-lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diam made of the same material. A thermocouple well was located in the die body 3½ in. down from the top of the die, while another well was located centrally in the bottom punch 8½ in. from the bottom of the die. This die assembly was located in three cylindrical ceramic heating furnaces placed in tandem. Each furnace was controlled individually by a Variac power transformer. In turn, the die and furnaces were placed in a water-cooled stainless steel pot which could be evacuated. A cover, which contained a centrally located Wilson seal with an 18-4-1 1 in. diam ram running through it, was bolted on the pot. After sealing, the pot was evacuated by a roughing pump to 200 microns pressure, after which a diffusion pump was used to bring the pressure down to 5 to 15 u. At this pressure, the furnaces were turned on. As soon as they started to heat, out-gassing of the entire unit raised the pressure to 30 to 400 p. By the time the specimens were at temperature ready to be pressed, approximately 4/2 hr, the vacuum pumps had re-established the 5 to 15 u pressure. Once the desired temperature was reached, the required pressure was applied for a predetermined length of time to the 1 in. ram, through to the top punch, and to the specimen. When the time for keeping the specimen under pressure had elapsed, the pressure was released, the energizing coil current turned off, and the assembly allowed to cool. After cooling, the die was removed from the pot and the specimen was ejected. Specimen Preparation: Two different types of specimens were made for this investigation. One was for subsequent tensile testing, while the other was for determination of intermetallic alloy zone penetration into the parent metals. Tensile Bars—Commercially rolled copper pieces in. thick or zirconium sheet pieces 1/32 in. thick and 1.366 in. diam were placed between commercial 2-S aluminum rod 1 in. thick and 1.366 in. diam. This sandwich in turn was slipped into a 2-S aluminum sleeve 1.438 in. OD and 1.370 in. ID. This sleeve lined the couple up and prevented the aquadag lubricant from getting in between either the A1-Cu or Al-Zr interfaces. Immediately prior to the specimen assembly, the copper or zirconium was abraded on the flat surfaces with 320 grit silicon carbide paper, producing clean smooth surfaces. The aluminum was chemically cleaned just before assembly by: l—degrease in acetone, 2—distilled water rinse, 3—immersion for 3 min in 5 pct NaOH at 70" to 80°C, 4—distilled water rinse, 5—immersion for 2 min in 50 pct HNO3 solution at room temperature, 6—distilled water rinse, and 7—drying in a blast of gas. After the A1-Cu sandwiches were hot pressed and ejected, the specimens were machined such that the aluminum sleeve was removed, and the remaining aluminum was then threaded; the bar so produced was tested later for tensile strength. In all the instances where Al-Cu couples were tested, the specimens broke during the test at the Cu-A1 interface and never within the aluminum or copper. The ultimate tensile strength values at times showed considerable scatter for a set of given reaction conditions. Because of this, as many as three to five specimens were made for a particular set of conditions. The trend of the average tensile strengths obtained was not as conclusive as was the trend of the maximum tensile strengths, the latter values being obtained under optimum reaction conditions. Therefore, the values of ultimate tensile strength given herein are maximums.

Jan 1, 1956

By W. Rostoker, A. Siede

THE venerable problem of hydrogen embrittlement of ferritic iron lacks as yet a complete explanation. Possibly part of the difficulty has been the exclusive preoccupation with the total ductility prior to fracture. In the past few years it has been noted at least twice1,2 that hydrogen charged into iron has the ability to depress the upper yield point and, at room temperature, to eliminate completely the discontinuous yield phenomenon. Cracknell and Petchl rationalize that the depression of the yield stress is an example of the behavior of inhomogeneous stresses. Their explanation requires that microcracks exist in the annealed metal, and that hydrogen collect in these cavities under high hydrostatic pressure. The hydrostatic pressure of hydrogen generates localized tensile stresses in the iron which, with external loading, reach the critical stress for yield prematurely. The local plastic zones will spread across the specimen before the Lüders bands can be generated, and the yield-point elongation phenomenon is eliminated. This viewpoint will be discussed in succeeding paragraphs. Rogers,2 on the other hand, represents the depression of the initial flow stress as a result of the interaction of hydrogen with dislocations. He submits two alternative modes of interaction. In the

Jan 1, 1959

By AIME AIME

MICA is perhaps our No. 1. strategic mineral problem because of its large requirements in a variety of equipment for use in the military services, and because the principal source of this material has heretofore been British India, a source now threatened partly because of distance and lack of ships. [Block mica and bauxite were added to the "most critical" list published by the W.P.B. on Nov. 6.] No satisfactory substitute has yet been found for most of the uses of mica, which largely involve electrical insulation. Brazil is now our nearest and best major source of this material. No splitting plants have yet been established there but in 1941 we imported about a million pounds of block mica from that country and in 1942 that quantity will be considerably exceeded. In Brazil, mica is found almost exclusively in the pegmatite dikes along the mountain range bordering the eastern part of Minas Gerais. A belt, roughly 180 miles long by 100 miles wide, extends from Theophilo Ottoni to Carangolo. The principal mica-mining districts in this belt are the Governador Valladares area to the north and the Espera Feliz district to the south. The dikes are usually 10 to 50 meters wide and a mile or two long and intrude the old metamorphic schist formation. They are weathered and easily mined.

Jan 1, 1942

By R. K. Ham, M. L. Wayman

TD-Nickel has been broken in tension and in fatigue at voom temperature. Rod specimens failed in tension by necking, with axial cracks attributed to voids elongated in the extrusion direction. Fatigue specimens failed in shear. Thin-film electron microscopy showed that the subgrain structure of TD-Nickel was very stable, and that particle-matrix detachment was very difficult, in tension and fatigue. TD-Nickel softened slightly during fatigue but had a high fatigue ratio (0.5at 10&apos; cycles). Fractography suggested that Stage I fatigue crack propagation is greatly extended in TD-Nickel. Td-NICKEL* is a dispersion of 2 pct by volume of thoria (ThO2) in nickel, produced by powder-metallurgical methods including compaction, sintering, and extrusion. The spherical thoria particles, which may have a mean diameter of a few hundred angstroms, are dispersed with a mean planar spacing of a few thousand angstroms. By a combination of cold working and annealing, a subgrain or cell structure of dislocations intimately associated with the dispersion can be produced.&apos; This gives the material useful tensile properties which are extremely resistant to exposure to high temperatures.&apos;-= At the same time, the material shows considerable ductility.3&apos;4 At the beginning of the present work, it was considered of great interest to investigate the mechanical stability of TD-Nickel under conditions of fatigue. On the one hand, materials which derive strength from a cold-worked structure are unstable in that they are susceptible to fatigue softening: in addition, the presence of discontinuities such as the particle-matrix interfaces might be expected to assist in the initiation and propagation of fatigue cracks, in that they may provide local concentrations of internal stress and sites for the initiation of voids." On the other hand, the substantial ductility of TD-Nickel suggests that if it obeys Coffin&apos;s relation8 (or the more refined form proposed by Manson9) it should have good fatigue resistance. The initial purpose of this investigation was to assess the importance of these factors. Also, relatively little fundamental work has been done on the mechanism of fatigue in dispersion-strengthened materials. Work on overaged A1-4 pct CU10-12 revealed a very large Bauschinger effect indicative of internal stresses at the particles, and very great fatigue hardening1&apos; presumably due to the multiple slip stimulated by these internal stresses, followed by softening which was initially due to softening in the matrix, but later might have arisen from cracking at the particle-matrix interfaces. The study of overaged Al-4 pct Cu could not settle this latter point by the electron microscopy of thin films, since the dispersion is too coarse. A previous study of the fatigue of internally oxidized copper13 was complicated by inter granular failure, attributed to oxide particles at grain bouhdaries; internal oxidation of single crystals, however, improved their fatigue properties.&apos;3 Investigations of SAP (sintered aluminum powder) are complicated by the complex particle shapes, and the possibility of continuous internal oxide films.14 It was hoped to avoid these difficulties with TD-Nickel, which had the further advantages that it was commercially available and suitable for study by the thin-film technique. 1) MATERIALS AND EXPERIMENTAL PROCEDURE TD-Nickel was purchased from the Driver-Harris Co. as 3/9-in.-diam rod which had been extruded, swaged, and "stress-relieved" (normally at 1010°C for 1 hr). Continuous-radius fatigue specimens with a minimum diameter of -0.1 in. were ground to shape and electropolished in 40 pct phosphoric, 35 pct sul-furic, 25 pct water at 25oC, with a stainless-steel cathode, at -6 v. Fatigue tests were carried out at room temperature with a Sonntag SF-1-U machine operating in push-pull at 1800 cycles per min, and in an Instron TT-C-L modified for reversed stressing at 26 cycles per min as described elsewhere.10 Round tensile specimens were ground with 0.85-in. gage lengths of 0.135 in, diam, electropolished, and tested in a Tinius Olsen hydraulic machine. The surfaces of fatigue specimens were examined with a Reichert metallograph. Discs for electron microscopy with a Siemens Elmiskop I were spark-cut 0.01 in. thick with a modified Servomet 11 employing a tool of moving molybdenum wire, cleaned in 50 pct acetic, 30 pct nitric, 10 pct phosphoric, and 10pctsul-furic at 85oC, and thinned by the window method in the electropolishing solution at -20°C and -6 v. Two-stage replicas (parlodion, then Pt-50 pct C self-shadowed at 40 deg) were taken from fatigue fracture surfaces for electron microscopy. Plane sections parallel to the specimen axis and containing the direction of fatigue crack propagation were polished, etched with Carapella&apos;s reagent, and examined optically. Transmission Laue X-ray photographs of as-received material electropolished to a point were used to determine preferred orientation. 2) RESULTS 2.1) The Structure of As-Received Material. Grains -1 µ diam and elongated 20 to 30 u in the direction of the rod axis were observed, With&apos; elongated "intergran-ular" voids (-4 p diam and -90 µ long and identified as such using longitudinal and transverse sections and

Jan 1, 1968

By Sydney H. Ball

I. INTRODUCTION. DURING the past 50 years the attention of mining-men has been turned to Africa, and within the past decade prospecting-expeditions sent into Central Africa have resulted in the opening-up of several mines. Having recently spent two years in the Belgian Congo for the Société Internationale Forestiere et Miniere du Congo, it is our purpose to outline briefly the mining-conditions in that part of Central Africa. Before it became, in 1908, a Belgian colony, this region was known as the Congo Free State. II. LOCATION AND AREA. The Belgian Congo lies in southwestern Central Africa, west of the continental divide, is illustrated in Fig. 1. It has a coastline of but 20 miles on the Atlantic, but widens rapidly eastward to points 5° north and 14° south of the equator. Its area is 908,000 sq. miles, which is almost one-quarter that of the United States and Alaska, or more than one and one-half times that of Alaska. Stated in other terms, its area is nearly one-third that of the United States, exclusive of Alaska and the insular possessions, or more than that of all the United States east of the Mississippi river. III. TOPOGRAPHY AND DRAINAGE. From north to south, Africa is made up of three topographic elements: 1, the Atlas mountains, a highly-accentuated region

Apr 1, 1910

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company&apos;s underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905