Search Documents

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By J. N. Stevens, M. Tulwin, P. J. Lawlor

All metals producers are on an unending search for a competitive advantage. They need to produce in the most cost effective way. Sometimes a new mill might be considered but in this paper we present examples of how this might not always be necessary. A detailed investigation by an equipment vendor who can consider the mill and or plant as a complete entity: mechanics, automation and process control can often find solutions that are both lower cost and can be implemented in shorter time frames.

Oct 1, 2019

By Božidar Šarler, Umut Hanoglu

A rolling simulation system has been developed to calculate the macroscopic rate of deformation, stress, strain, and temperature fields by using a novel meshless method. The model is based on two-dimensional traveling slice assumption. The slices are aligned towards the rolling direction. The initial size of the billet, bloom or slab and the geometry of the grooves at each rolling stand, the distances between the rolling stands, and continuous or reverse rolling can be arbitrarily considered. The purpose of this paper is to complement these development by predicting and visualizing also the grain size of steel over the strand cross-section for each position in the rolling mill. The grain size models have been in one-way coupled to the macroscopic calculations. First the critical strain for dynamic recrystallization is being checked. If the calculated strain is higher than that, considering also the time for meta-dynamic recrystallization, dynamic or meta-dynamic grain size calculations are carried out. If the strain is too low then only the static recrystallization is considered together with its required time. Finally, austenite grain size and ferrite grain size are calculated respectively as the steel cools down. The listed physical models are based on collection of empirical relations found in literature. The user of the system is free to choose or create the model he wants with his own parameters. The simulation system has been coded as a user friendly computer application for an industrial use based on C# and .NET framework and runs on regular PCs. The computational time for a rolling simulation is usually less than one hour and can thus be straightforwardly used for optimization of the rolling mill design in a reasonable time.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By Luigi Giacomini, Bruce Kiefer

A new plant for special steel long products was commissioned in recent years at Dangjin, South Korea, for Hyundai Steel. Two multi-line rolling mills can produce yearly 1 million tons of billets, straight and coiled bars, with dimensions from 5.5 to 350 millimeters. The products are used for manufacturing engine and transmission components used by Hyundai Kia Automotive Group. The processed grades include carbon, special alloy, spring, bearing and free-cutting steel. The first mill rolls blooms into finished large round and square products, as well as into intermediate billets. A 2-high reversing breakdown stand is followed by a finishing and sizing train with CGA stands equipped with an under-load roll parting system for automatic gap control. The second mill combines lines of small bars, rods and bars-in-coil. Billets are rolled in a continuous rolling mill with original RedRing Series 5 stands. The rod outlet features Morgan No-Twist and Rod Reducing/Sizing mills, Morgan High-Speed Laying Head and Stelmor conveyor. Advanced sensors and electronics integrate with mechatronic packages, thus equipping the mill for Industry 4.0 applications. Hyundai can meet the demanding requirements posed by the automotive industry and benefit from optimized conversion costs, the flexibility to meet market changes, achieve high product quality, and reduce floor personnel.

Oct 1, 2019

By Franco Gandin

With increasing demands for highly performing and at the same time efficient and running-costs saving vacuum-degassing equipment, dry mechanical pumps have been confirmed a proper choice to completely fulfill the expectations of steel-making companies worldwide. Regarding the production of both special carbon steel and stainless steel grades, the usage of mentioned pumps allowed reaching simultaneous remarkable results from different viewpoints in various Danieli worldwide installations (treating up to 200 t of liquid steel). As a matter of fact, in front of the replacement of a widely spread and renowned technology such as steamejector pumps with the recently developed technology embodied by the dry mechanical pumps, well-established metallurgical performances in terms of carbonhydrogen- nitrogen-sulphur removal have been repeatedly attained while meeting at the same time the client’s expectations concerning, for example, running-costs and push-button availability. Additionally, thanks to the very flexible, modular, redundant and maintenance-friendly equipment design, random problems occurring to the singular mechanical pumps can be easily solved without affecting the VD-VOD plant availability and metallurgical performance. With a particular regard to the VOD process, a very short overall process-time has been repeatedly performed (averagely less than 58min under-vacuum time at ChMP1) while guaranteeing the expected required quality of the final refined stainless steel. Moreover, in several VOD installations (ranging from 6 t up to 110 t of liquid steel) an efficient automatic process control such as dynamic pressure-regulation during oxygen-blowing has been attained thanks to the controllable variable-speed drives with which each mechanical pump is provided.

Aug 17, 2017

By Charles Sóstenes Assunção

A mathematical model of heat transfer and solidification for a continuous casting of round billets was developed. The water flux density of the secondary cooling zone was experimentally measured, using an apparatus in industrial scale with two types of nozzles, flat jet and full cone jet. The profiles of water distribution were applied on the mathematical model. The results showed that the water distribution is not uniform in both longitudinal and angular directions owing to the unevenness of the spray and to the curvature effect of the round billet. This non-uniformity causes important variation of the heat transfer coefficients and superficial temperature of the billet, especially in the first cooling zones, where the temperature is higher. The mathematical model was used to simulate a change of nozzle type in the first cooling zone. The results showed that the heat flux and superficial temperature variations were reduced with a full cone jet nozzle in comparison with the flat jet nozzles.

Aug 16, 2017

By Jörg Busch

The essential pre-requisite for attaining the high quality of product required from high-speed continuous production processes is the use of new measurement and control technologies. High availability and reproducible measuring results ensure the high level of process stability necessary for full continuous operation. The requirements for the optimisation of quality across the complete production process and for quality analysis systems will be discussed. This report will present examples of basic and new measurement technologies in Cold Rolling Mills and Processing Lines. The following gauging systems will be discussed in detail: Strip tension meter, roll force measurements, weighing systems and shapemeter rolls. The measuring and control systems in this presentation must be seen as high-tech solutions in the field of processing technology. The measuring methods and technologies described are, together with optimised process models and precision control loops and actuators, the main pre-requisites for achieving the quality of product required from high-speed continuous production processes. Interconnected quality management systems enable optimisation across the complete production process.

Jul 30, 2018

By Claudio Fabbro

The increasing demand of wire rod high carbon grades for both small and large sizes are challenging the wire rod producers to enhance new technologies by combining high plant productivity and efficiency of superior quality finished products with extreme process flexibility. The possibility to change process route according to the final application of the rolled steel grade and to simplify production planning is one of the most important keys to success that distinguishes the mill plants developed by Danieli. This paper will focus on the most important metallurgical and process targets and on the in-line heat treatment technologies representing the core of Danieli know-how on high carbon grades production.

Jul 30, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Andrea Donadon

This article introduces the Danieli Total Asset Management System, which involves 360 degrees service methods and equipment. Danieli Condition Monitoring System and Danieli Torque Monitoring System are fundamental to evaluate the conditions of the working components in heavy duty transmissions. The first one monitors the vibrations and the lubrication fluid conditions with the purpose to identify the presence of malfunctions, by detecting any variation of the signals from the standard values. The second one monitors the transmitted torque for each spindle and gearbox, with the aim of detecting any anomaly in torque distribution and magnitude, and evaluating the residual life of the mechanical parts, on the base of a dedicated fatigue damage algorithm. All these features are useful in avoiding serious damages to machines, facilities and people, but allow also planning the maintenance and overhaul activities with efficiency, in order to achieve the best plant availability and reliability. The data analysis is made by the IntelliCMS software, which interfaces with plant and Danieli operators and includes the possibility to cooperate by remote connections, simplifying service activities and support. All these features allow providing new full service programs, where the client is totally supported in maintenance, overhauls and substitutions. This is the best way to ensure the most efficient, high quality and reliable after sales assistance.

Aug 16, 2017

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Matteo Tomba

Today’s steel market is characterised by high competitiveness and tight profit margins; therefore, the operational costs of rolling mills must be as low as possible, while ensuring a final product of the highest quality standards. PERT SRL is an engineering company with a long-term experience in the international steel market, specialised in the design and supply of highly innovative and bespoke solutions for siderurgical and environmental plants. Because of its strong commitment to deliver excellent products and services, and its ability to innovate and adapt to the fastchanging market requirements, PERT has studied a new generation of BI-SUPPORT rolling stands, designed to be used in rolling mill plants for the production of rebars, rounds and sections in special quality bars (SBQ) steel grade, wire rod, light and medium section, suitable also for special steel plants. This paper will provide a deep insight into the key technical and economic features that have revolutionised the rolling technology for long products, such as the absence of spindles and piping on board, the considerably reduced number of spare parts required, a ring gap regulation system, and the compact dimensions, which lead to significant savings in investments and production costs; at the same time, the BI-SUPPORT stands guarantee excellent standards to the final product, an increase in plant productivity and a general improvement in the plant management.

Aug 16, 2017

By Piotr Kula

Vacuum carburising with pre-nitriding (PreNitLPC® technology) involves feeding ammonia during the charge heating stage before carburising. The purpose is to restrict the growth of grain in the surface layer of the carburised steel. The article presents the influence of nitrogen on restricting austenite grain growth during vacuum carburising and on mechanical properties (fatigue strength, impact resistance) of layers that underwent such treatment in comparison with traditional carburising methods.

Aug 16, 2017

By Kíssia Carolina Bertoluci Cardoso

Para a fabricação de peças de grande porte, o forjamento em matriz aberta é o processo mais utilizado. Porém, se seus parâmetros não forem bem estabelecidos, defeitos metalúrgicos poderão surgir; esses, em sua maioria, provindos do material bruto de fusão, como rechupes e vazios. Para sanar tais defeitos, a deformação imposta na peça deve ser a mais homogênea possível. Neste estudo, a simulação numérica foi utilizada para verificar a relação entre a largura de contato matriz-peça e a espessura da parede de peças vazadas, com o objetivo de analisar o conceito de razão de mordida para esse tipo de geometria. Utiliza-se um billet cilíndrico inicial de 450 mm de comprimento, 360 mm de diâmetro externo e 120 mm de diâmetro interno, de material AISI 4140. As razões de mordida estudadas variam entre 0,2 e 1,4, sendo impostas variações de tempo em cada processo. Após análise, pôde-se verificar que as geometrias que apresentam distribuições mais homogêneas de deformação utilizaram razão de mordida de 0,4.

Aug 16, 2017

By Diogo Barcellos Moraes

O presente trabalho tem como premissa abordar estudos baseados na metodologia Troca Rápida de Ferramentas (TRF ou em inglês, SMED – Single-Minute Exchange of Die), e realizar um estudo de caso na empresa Votorantim Siderurgia. O objetivo principal é a redução do tempo de setup da máquina de Tela de Coluna, a fim de minimizar o desperdício de tempo e maximizar a produtividade. Além disso, obteve ganhos efetivos no layout de ferramentas, programa 5S, tempo de atividades, entre outros.

Oct 30, 2017

By Carolina Gomes Dias Ribeiro

The modern composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace. Natural fibers composites with biodegradable polymer matrices are considered environmentally friendly materials and currently accepted as possible substitutes for synthetic composites. These green composites can be safely discarded or composted at the end of their life without harm to the environment. Another alternative for synthetic composites is to apply natural lignocellulosic fibers as reinforcement of conventional polymer matrices and already used in the automobile industry. In addition to the environmental and societal advantages of the green composites, the lignocellulosic fiber reinforced conventional polymer composite also has economical and technical advantages. In the case of a fiber collected as a waste, the price of the composite can be considerably lower than “fiberglass”. Furthermore, with high strength lignocellulosic fibers such as sisal, ramie and malva the specific strength of a composite may approach that of “fiberglass”. Therefore the objective of the present work is to investigate the mechanical behavior of polymer matrix composites reinforced with high volumes of natural malva fibers subjected to tensile stresses.

Aug 16, 2017

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Luana De Lucca de Costa

O forjamento a quente em matriz aberta é, atualmente, o processo mais utilizado para a fabricação de peças de grande porte. Neste estudo, a simulação numérica foi utilizada, através do método de elementos finitos, para análise do processo de forjamento em matriz aberta de um eixo vazado e escalonado aplicável em aerogeradores. A partir de um billet cilíndrico vazado de aço AISI 4140, pesando 1 kg, é simulado o processo de forjamento objetivando a obtenção de geometria final apresentada. Utiliza-se matrizes superior e inferior em formato côncavo, e um mandril de manipulação com inclinação de 1,15°. A cinemática da simulação numérica, que inclui 4 passes com um número total de 30 cursos, é avaliada. Ao comparar a geometria apresentada com a obtida observa-se que o alongamento longitudinal da forma final é obtido. A partir da análise da temperatura, pode-se concluir que o reaquecimento deve ser realizado após cerca de 45 s, no final de cada série de 5 cursos.

Aug 8, 2018