Search Documents

By Cristiano José Scheuer

The effect of low-temperature plasma carburizing treatment on the micro-abrasive wear resistance of AISI 420 steel was investigated by mean of a CSM Calowear ball-cratering equipment. Carburized samples were treated at temperatures of 350, 400, 450 and 500°C for a fixed time of 12 h, using a gas mixture containing 99.5% (80% H2+20% Ar)+0.5% CH4. Micro-scale abrasive wear tests were conducted with a 25.4 mm AISI 420 steel sphere, using an abrasive suspension of alumina (Al2O3) with particle size of 1 ?m (abrasive concentration of 0.11 g/cm³). The contact normal force, abrasive flow and ball rotation speed were fixed at: 0.5 N, 0,2 drop/s, and 120 rpm. The wear craters were analyzed using a confocal laser microscope, Olympus OLS 3000. The wear analyses were performed for test times of: 30, 60, 90, 120, 180, 360, 540, 720 and 900 s (equivalent sliding distance: 0.84, 1.68, 2.52, 3.36, 5.04, 10.09, 15.14, 20.19 and 25.23 m, respectively). The results indicate that the wear coefficient in the outer layer and in the diffusion layer are different, being lower in the latter. It was also verified that the wear coefficient on the outer layer region decreases with increasing treatment temperature in the range of 350 to 450 °C, and increase again for 500ºC. The diffusion layer wear coefficient is similar for all the carburized samples. Finally, for all studied conditions, the analysis of the wear craters surface indicates the occurrence of grooving and micro-rolling abrasion wear modes.

Aug 8, 2018

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Wolfgang Oberaigner

Primetals Technologies has always been a driver of innovation in steelmaking, especially by providing sophisticated process expert models for continuous casting machines. This capability is demonstrated by recent advancements in automation solutions that include: DynaPhase, Dynacs 3D, and DynaGap. This state-of-the-art suite of dynamic secondary cooling and soft-reduction packages take into account thermodynamic effects such as shrinkage and phase transitions, and thereby significantly contribute to direct quality improvements during the solidification phase in the continuous casting process. Speed Expert calculates an optimum casting speed for every casting situation, and additionally recommends a strand speed so that the point of final solidification is positioned at the end of a segment for optimum soft reduction. In the case of steel grade changes, the Intermix Expert precisely calculates the chemical properties of the mixed steel, thereby minimizing losses due to deviations from required specifications. The Nozzle Expert is a new model that detects clogged nozzles and broken hoses in secondary cooling systems. The first installations were highly successful and customers are pleased with impressive reductions in maintenance costs and improved steel quality. This paper describes these innovative process automation solutions and gives an overview about the successful results achieved within the first installations.

Aug 16, 2017

By Dagoberto Brandão Santos, Kairo de Barros Guimarães, Túlio Magno Füzessy de Melo

The effect of the cooling conditions on the microstructure and hardness of a Dual Phase hot-rolled steel 800 MPa strength was investigated. Simulations of the cooling conditions using a dilatometer were carried out from samples of a hot rolled coil with variations of the intermediary temperature from 620 to 740°C, isothermal holding time between 1 and 10 s and coiling temperature between 50 and 400°C. In addition, two CCT (Continuous Cooling Transformation) diagrams were developed to evaluate the effect of the isothermal holding time on the phase transformations of the remaining austenite. It was observed that the intermediary temperature has a strong influence on the kinetics of the phase transformation, as well as the isothermal holding time influences the amount of ferrite formed and, consequently, the final microstructure and hardness of the material. The coiling temperature did not cause significant changes in the amount and morphology of the ferrite, but a gradual replacement of martensite with bainite was observed, which, in addition to the self-tempering effect, contributed to the hardness reduction.

Oct 1, 2019

By Fábio Dian Murari, Antônio Adel dos Santos

The effect of reheating temperature of slabs on the precipitates dissolution and mechanical properties of Ti-Nb microalloyed steel was investigated in pilot scale. It was verified, by means of transmission electron microscopy, a significant decrease in precipitates formed during the solidification of the steel as the reheating temperature increased from 1100°C to 1200°C. No significant changes in size and shape of the precipitates were observed with further temperature increase up to 1280°C. In line with the precipitates dissolution behavior, an increase in strength was observed with the elevation of the reheating temperature up to 1200°C, due in part to the reprecipitation of fine Nb-rich precipitates during the hot rolling. At 1200°C the presence of deformed ferrite on the microstructure contributed to the additional increase in strength. After reheating above 1200°C up to 1280°C, a decrease in strength of the rolled plates was noticed. This effect has been credited to the absence of deformed ferrite grains and also to a small increase in the low angle grain boundaries size. The results were in agreement with Thermo-Calc and Dictra simulations.

Oct 1, 2019

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By John Ross Middleton

Based upon 30 years+ experience in the Development, Implementation and Ongoing Support of Computer based Melt Shop Management Systems in about 40 plants in the UK, Europe and the USA, consideration of the overall facilities of a state of the art, comprehensive, Integrated Melt Shop System covering Melting and Secondary processes for all grades of steels and superalloys; the scope of functionality of these systems, covering Raw Materials and Consumables Procurement and Inventory Management, Laboratory Management, Melt Shop Scheduling, Furnace Charge and Additions Optimisation, Level 1.5 to Level 2.5 Materials Optimisation and Process Control Calculations, Process Data Recording, Management of Ladles, Furnace Bodies, Vessels and Moulds, Comprehensive Management Reporting and Integration with Corporate ERP Systems. The second section of the paper reviews the key ‘Success Factors’ to achieve rapid, successful implementation, comprehensive, fast response user support, continuing system improvement and maintaining ‘perfect fit’ of system to operations in an ever changing future technical, operations and business environment.

Jul 29, 2018

By Hormando Leocadio, CWM van der Geld, Julio Cesar Passos

Impinging water jets promote high heat flux extraction rate. Steel industry widely employs the process for accurate temperature control to improve the microstructure and to ensure adequate mechanical properties. The range of surface temperatures, heat fluxes and cooling rates are very large, which makes it important to obtain an accurate value of the heat transfer coefficient. This paper presents an experimental and numerical study of the heat transfer behavior of a high temperature (450°C - 900°C) steel plate cooled by a water jet at 20°C to 70°C. High-speed imaging (up to 20,000 fps) within water jet impingement zone allowed the characterization of the boiling regimes in the early stages of cooling. The effects of initial temperature, water jet temperature and velocity on the heat transfer coefficient were analyzed by inverse heat conduction method that predicts the heat flux and temperature on the top surface from temperatures measured with thermocouples inserted in test plate. Heat transfer is strongly affected by the initial temperature of the hot steel, water jet temperature and, less intensely, by jet velocity. High cooling rates start when liquid water is in direct contact with surface temperatures above 700°C.The results will contribute to the enhancement of the temperature cooling control on the runout table and cooling model employed at Usiminas Hot Strip Mill.

Oct 1, 2019

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Andreas Jungbauer

Two Arvedi ESP plants going into operation in 2015 will allow a Chinese steel producer to better serve the extremely attractive local and export markets for high-quality, thin-gauge strip products. The energy consumption and the related costs are reduced by up to 45% compared to conventional casting and rolling processes. This also means a major reduction in CO2 emissions. The new plants are designed for an annual production capacity of 2 x 2.55 million tons of high-quality, ultra-thin, hot-rolled strip products with widths of up to 1,600 mm and thicknesses down to 0.8 mm. The project scope also features a comprehensive training and assistance package for plant start-up and operations by personnel from the existing ESP plant at Acciaieria Arvedi SpA, Italy. The plant setup, the trainings and assistance program as well as latest results from the ESP plant in Italy will be presented. While this project is under execution three further ESP lines have been ordered by the same customer summing up now to five ESP lines at the same location.

Jul 30, 2018

By Cleber Caetano Thomazi

Rotary kilns are continuous process equipment used on calcining of nickel ore. The chemical and physical reactions are created by means of heat up the material to predetermined temperatures. Tertiary air fans are attached to the kiln shell to maintain oxidizing/reduction conditions. Special ducts orientate the air flow inside the kiln. In the present work, two types of failure on distinct tertiary ducts mounted on the same kiln are reported. Chemical analysis, hardness test, metallographic and fractographic examinations were carried out. Fabrication related problems and creep were identified as the root causes of damages.

Oct 30, 2017

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Augusto Lachini Pereira, Julio Aníbal Morales Pereira

The capacity of steelmaking slags (CaO-SiO2-Al2O3-MgO) on inclusion removal from liquid steel was investigated through experimental conditions. Laboratory experiments with slag and steel samples (with inclusion population known) were performed using a vertical electric resistance furnace at 1600 ºC. After the melting experiments, slag and steel samples were separated and analyzed regarding their chemical composition and inclusion population evolution. The capacity of slags on inclusion removal was evaluated based on the thermodynamics (solid and liquid phases proportion, phase composition and effective viscosity of slags) calculated using the FactSageTM 7.2. Results indicated that changes in the composition of slags (regarding CaO/SiO2 e Al2O3) presented effects on the steel cleanliness. The total inclusion density decreased in all steel samples and the removal of inclusions by slags shows a tendency to improve as their viscosity decreases (< 0.23 Pa.s).

Oct 1, 2019

By Elham Kordzadeh

As the world’s reserves of coarse and high-grade iron ores continue to shrink, beneficiation is becoming increasingly important. The resulting concentrates cannot be used directly as feedstock for iron making, but require an additional agglomeration step. Pelletizing is preferred, because the uniform chemical, physical, and metallurgical characteristics of pellets make them a more desirable feed for the iron making processes. The heat hardening or induration of pellets is typically done in shaft furnaces, grate-kiln systems or on straight grates. Rotary kilns were originally developed in the late 19th century for Portland cement production [1]. The main development work for the successful adaptation of the process to the thermal treatment (induration) of green balls from iron ore was performed by Allis Chalmers in Milwaukee, Wisconsin, USA in the 1960’s [2].The straight grate process, which was first used in 1955 at Silver Bay, Minnesota, was a dedicated development with the aim to pelletize and indurate magnetite (taconite) concentrate [2]. There are various important technical and economical distinctions between the two pelletizing technologies. The most important differences include that a grate-kiln has three distinct pieces of equipment, a preheat grate, a rotary kiln and an annular cooler, whereas in the case of a straight grate, the entire indurating process is done on one piece of equipment only. In addition, both technological solutions have differences in their recuperation systems, direction of air flow in drying, number of burners, form of pellet movement, etc., which cause differences in raw material suitability, process control, economical aspects, plant operation and product pellet quality.

Oct 30, 2017

By Steferson Ferreira de Oliveira

Desenvolvido nos últimos anos, o processo NDE, vem se tornando uma maneira promissora de usinar e nitretar simultânea a superfície de materiais metálicos. A Usinagem por Descargas Elétricas (EDM) é um processo de usinagem não convencional que tem grande potencial em aplicações de engenharia de superfície, ao melhorar a resistência superficial do material por meio de tratamentos termoquímicos, como por exemplo, a nitretação. Propriedades como: baixa densidade, boa resistência à tração (comparável à de muitos aços ligados) e excelente resistência à corrosão, possibilitam a aplicação do titânio e suas ligas nas indústrias aeroespacial, naval, química e automotiva e ainda no campo da medicina. Porém, raramente são usados como peças sujeitas ao deslizamento, devido a sua devido à sua baixa resistência aos mecanismos de desgaste abrasivo e adesivo e alto coeficiente de atrito. O tratamento termoquímico de nitretação pode solucionar esta restrição. Além de aumentar a resistência ao desgaste, o nitreto de titânio melhora a biocompatibilidade de suas ligas. O objetivo deste trabalho foi estudar a camada nitretada na liga de titânio Ti6Al4V por meio do processo de Nitretação por Descargas Elétricas (NDE), usando como fluído dielétrico solução de água deionizada e ureia granulada, como fonte de nitrogênio. Uma máquina de EDM por penetração foi utilizada no processo. Cobre e grafite foram utilizados como materiais dos eletrodos ferramenta. Foi avaliada a usinabilidade da liga Ti6Al4V com solução de água e ureia, relacionada aos parâmetros: taxa de remoção de material (TRM), taxa de desgaste (TD) e desgaste volumétrico relativo (DVR) para eletrodo de cobre e de grafite. Para caracterizar a camada nitretada foram realizadas microscopia óptica e medição de microdureza Vickers. A formação de nitretos na superfície foi avaliada por meio de difração de raio-x. Imagens metalográficas da seção transversal da superfície mostraram a formação da camada nitretada, devido ao ganho no valor da dureza. Os parâmetros relacionados à usinagem apresentaram valores que indicam um melhor desempenho quando se usa eletrodo ferramenta de cobre em relação à grafita. Nitretos de titânio foram observados no difratogramas da amostras nitretadas por NDE.

Oct 30, 2017

By Edilson Alves Maranhão, Willi Anton Buehler, Andrea Pezza

O processo de vácuo é a solução típica aplicada quando é hora de atualizar o nível de qualidade do aço de uma aciaria existente. A instalação do novo RH de 150t na planta integrada no México e do novo Tanque de Desgaseificação à Vácuo (VD) de 135t no Canadá para a produção de tubos de alta qualidade na América do Norte, é um exemplo típico disso. A nova instalação inclui o mais recente conceito de design para este tipo de equipamento: operações totalmente automatizadas e menor impacto ambiental são os principais aspectos do projeto. A solução de bomba mecânica a seco continua sendo a melhor abordagem de investimento e custo operacional para a tecnologia de vácuo. Os principais aspectos do design da planta são descritos neste documento. O desgaseificador a vácuo RH é responsável pela melhoria das performances metalúrgicas, especialmente em termos de nitrogênio, remoção de hidrogênio e nível de pureza do aço. O processo a jusante e os resultados estão estritamente ligados aos desempenhos do desgaseificador a vácuo. O monitoramento de processos através da linha completa é uma prática padrão para obter uma melhoria efetiva da qualidade do produto. Os desempenhos metalúrgicos do desgaseificador a vácuo RH são analisados e comentados neste trabalho.

Oct 1, 2019

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do alto-forno (AF) está ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas (MP), especialmente, as do coque. As propriedades do coque são reflexos das propriedades dos carvões que lhe deram origem. Em termos de propriedades ligadas à natureza do carvão, a qualidade do coque é bastante influenciada pelo rank dos carvões, que compuseram sua mistura, ou seja, quantidades de macerais reativos e inertes, bem como suas propriedades coqueificantes, que é, exatamente, a habilidade inerente aos carvões aglutinantes de quando aquecido, amolecer, tornar-se plástico e solidificar em uma massa coerente. Neste contexto, o presente trabalho se propõe a evidenciar as mudanças no modelo de britagem de carvões da Gerdau Ouro Branco, bem como a operacionalização do padrão criado. Após a implantação, verificou-se a elevação de 1.8% em DI.

Aug 17, 2017

By Renato Cortes, Claudia Lopes, Ewerton Campos, ALEXANDRE CALDELLAS BARBOSA

São diversas as razões para se utilizar a realidade virtual (RV) em treinamentos, dentre elas pode-se destacar a redução de custos, redução de riscos ao ambiente e envolvidos e também a possibilidade de reproduzir ou simular situações impossíveis, muito complexas ou ainda em outro lugar ou até mesmo em outro espaço temporal. Nesse trabalho será apresentado um estudo exploratório sobre o uso de RV, realizado uma pesquisa de mercado e apresentado o estudo de caso de como a ArcelorMittal Tubarão vem trabalhando essa tecnologia nos seus treinamentos corporativos no ano de 2019. A aceitação da tecnologia pelos empregados nos treinamentos foi acima de 98% e também foi demonstrado que além de aumentar a atratividade e a retenção do conhecimento, os ganhos foram ligados também a redução de riscos, redução de tempo de treinamento, experimentação de situações críticas, redução de custos, ou seja aumentou a eficiência e eficácia do treinamento.

Oct 1, 2019

By Cyro Takano

A degradação durante o processo de redução de minérios de ferro é bastante conhecida pelos fenômenos de crepitação e inchamento. Em aglomerados a frio, auto-redutores utilizando cimento como aglomerante, há também degradação pela decomposição de hidratos que conferem resistência a frio, além de aumentar os vazios deixados pelo consumo do redutor. Outro fenômeno que afeta na velocidade da reação de redução é a formação de escória. Esses aspectos são analisados neste trabalho e principalmente em processos de auto-redução.

Oct 30, 2017