Search Documents

By E. R. Bauer

Prolonged exposure to noise can cause permanent damage to the auditory nerve and/or its sensory components, known as noise induced hearing loss (NIHL). It is the most common occupational disease in the United States today. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is addressing NIHL in the mining industry through several research efforts. This paper presents a general review of NIHL, the status of NIHL in mining, the results of the longwall noise surveys, and a review of the longwall engineering controls research efforts.

Jan 1, 2008

By Curtis Wilson

FROM the results of his investigation of the hardenable copper-nickel-silicon and copper-cobalt-silicon alloys, M. G. Corson1 explained the dispersion-hardening effect by assuming the precipitation of the inter-metallic compounds nickel silicide and cobalt silicide, and on this basis he constructed diagrams for the pseudobinary systems copper-nickel silicide and copper-cobalt silicide. A consideration of these diagrams and of the factors that exert such an important influence upon the rate of precipitation, such as degree of supersaturation, nucleus number and rate of diffusion, leads to the expectation that the rate of precipitation of the silicides on reheating the quenched solid solutions at temperatures below the alpha-phase boundary should increase continuously as the reheating temperature is raised. The present investigation shows that while this rate does increase with the reheating temperature in a general way, it does not do so continuously. Supplements to Corson's diagrams are offered, showing the discontinuities, and slight modifications in the solubility curves are suggested.

Jan 1, 1933

By K. L. Paciorek

The primary objective of this program was to determine the toxic fume and fire hazard of materials used in the construction of mine stoppings and in the sealing and reinforcing of mine ribs and roofs. The materials investigated were: silicone, phenolic, and isocyanate-based rigid foams, as well as epoxy and acrylate mine sealants. Of the rigid foams tested, the X-156 urethane foam presented the greatest toxic hazard based on toxic load values hydrogen chloride was the main toxic species evolved by this foam. In 'lone of the isocyanate-based compositions was hydrogen cyanide the major component, but its contribution increased with temperature. The FS-24 urethane and Celotex Max-Seal isocyanurate foams had the lowest toxic load values, although these two foams have different applications for in-mine use. Of the two mine sealants tested, the latex /acrylic coating presented the greater toxic hazard with acetic acid being the main toxic species evolved.

Jan 1, 1983

By Quin Dennis

Process Optimization ?What is it really? It is NOT ?a larger fan to increase draft through a process ?a larger pump on a wet circuit ?a wider conveyor belt for solid materials ?a larger feed elevator into or out of a process These relieve individual constraints ??bottlenecks??and allow operation to the next constraint in the process ?It is also NOT about automating the operator ?which captures consistency but is not continuous optimization

Nov 1, 2011

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By H. C. Miller

"Introduction**The progress of the ""Safety First"" movement in the oil fields of California during the past few years has been remarkably rapid. It has been generally concede by those who have learned to value the life and limbs of their employees, that safety is essential to efficiency and no company that has a high accident rate can be considered an efficient organization. Accidents have a destructive effect on the morale of any body of workers and cause disorganization and delays.The increasing danger to life and limb involved in the drilling for and the production of oil and gas, has become so great that it is clearly evident that everything possible must be done to keep it within the narrowest possible limits.There is a tendency toward carelessness, especially by men who are employed in hazardous occupations. This is brought about by the familiarity of the risk under which they are working and in no industry is this more forcibly exemplified than in the oil fields. Men have performed the same or similar duties for many years and have worked around similar hazards and unprotected machinery until many have can entire disregard for the dangers surrounding then. Very often familiarity with a hazard occasions a contempt for that hazard which only too often results disastrously."

Dec 1, 1923

By K. C. Armstrong, A. B. Cron, L. A. Melis

"The Johnny Mountain gold mine in northern British Columbia, owned by skyline Gold Corporation, has been in operation since August 1988. Mill operating difficulties at the start of the operation resulted in a depleted cash flow situation and quick improvements were required to generate a self-sustaining financial basis of operation. In October 1988, Melis Engineering Ltd. was contracted to identify metallurgical difficulties, implement necessary modifications, and undertake mill operations and personnel training in order to achieve production targets.This paper presents the operating difficulties which existed at start-up and describes the methodology used to overcome production problems. Metallurgical testing results are described along with the modifications made to the milling circuit to suit ore metallurgy. Plant changes led to the operation of a simple gravity/flotation circuit to recover gold as bullion and in a copper concentrate. Operation of the originally installed cyanidation circuit was discontinued. This contributed to substantial savings in operating costs and virtually eliminated environmental problems. PROPERRTY LOCATION ANR DESCRIPTIONThe Johnny Mountain mine site is located in northern British Columbia along the Iskuit River about 60 km east of Wrangell, Alaska and 275 km north of Terrace, B. C.. A location map is presented in Figure 1 and a site plan is shown in Figure 2. The complex is located on a mountain plateau about 3, 600 feet above sea level. The plateau is flanked to the north by Johnny Mountain and surrounded on the other sides by steep cliffs."

Jan 1, 1990

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986

By Bjöm Böhle

Top-down construction (or cut and cover construction) is providing important advantages when comparing with conventional construction techniques for commercial developments with deep basements, underground car parks or near surface infrastructure and traffic tunnels. Main features are substantially reduced restrictions to surface usage, avoidance of intervention with adjacent property, provision of rigid substructures resulting in minimal deforma­tions and settlements and, last but not least, accelerated construction pro­gramme. The present contribution illustrates the construction method in general and elaborates in detail on the special foundation works for a major urban commercial high rise development requiring a six level basement structure.

Jan 1, 2006

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By J L. Carpenter, S M. Iveson, K P. Galvin

Wet beneficiation of iron ore fines less than 1 mm typically involves a desliming stage ahead of the fine gravity separation such as spirals. The desliming is achieved using a bank of cyclones. The reject ultra-fines emerge in the overflow stream at relatively low pulp density, contain high proportions of low-value slimes, but also well-liberated iron ore ultra-fines below 0.045 mm in size; however, recovering the valuable iron ore ultra-fines from this overflow stream presents a significant challenge due to the need to remove such a large amount of water and slimes.The REFLUX™ Graviton consists of distinct 3D-printed modular units, based on REFLUX™ Classifiers, which are rotated at high speed in a large centrifuge. This system has previously been investigated under semi-batch conditions, demonstrating the potential for precision separations with significant capacity. It has been shown that the throughput advantage of the inclined channels and G forces multiply. This is the first paper presented showing the performance of this system under continuous steady-state conditions. Ultra-fine silica in the size range of 0 to 0.045 mm was fed to the Graviton at different volumetric rates, fluidisation rates and pulp densities ranging from 2 wt per cent to 30 wt per cent, in order to develop a fundamental understanding of the system’s performance. Experiments were then repeated using ultra-fine iron ore.CITATION:Carpenter, J L, Iveson, S M and Galvin, K P, 2017. Separation of ultra-fine particles using the REFLUX™ Graviton, in Proceedings Iron Ore 2017, pp 141–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. Karimi

Artificial neural networks (ANNs) have found their applications in the modelling of unit operations of mineral processing plants. In this research, laboratory-scale tests were conducted, using a three-inch diameter Mozley hydrocyclone. Main parameters included pressure drop at inlet, solid per cent, vortex and apex diameter were adjusted. The corrected cut size (d50c) and the flow rates of underflow and overflow were determined. Multi layers perceptron (MLP) feed forward network architectures were designed to predict the responses. The results showed a good correlation between experimental and network output, for corrected cut size and flow rates. Keywords: hydrocyclone, artificial neural network, corrected cut size, flow rates.

Jan 1, 2010

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949

By Gavin Ritson, Chris Ward

"The oil sands industry is still fairly young with the first viable oil sand operation having been started in Alberta in 1960. Since then numerous modifications and improvements have been tried and implemented. The current process makes use of high velocity pumping of oil sands slurry with hot water (hydrotransport) to achieve separation of bitumen from the sand.A number of the oil sands processes have been adapted from unit operations that are used in mineral processing, such as crushing, screening, flotation, cycloning and thickening. This paper outlines a typical oil sands process flowsheet and investigates the differences and similarities in technologies and costs to other mineral processing industries. It also considers the very large throughputs required, and presents some of the difficulties and challenges currently faced by the industry as a result of high demand for oil and environmental pressures.INTRODUCTIONOil sands (also known as tar sands) deposits are found throughout the world. The Athabasca Oil Sands deposit in Aberta is the largest of these. Oil sands consist of a mixture of crude bitumen (a semi-solid form of crude oil), silica sand, clay minerals, and water. The Athabasca, Peace River and Cold Lake deposits cover 141,000 square kilometers and contain about 1.7 trillion barrels (270×109 m3) of bitumen in-place, comparable in magnitude to the world's total proven reserves of conventional oil"

Jan 1, 2009

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Tang Chaoho

Laboratory research on the reducing and matte smelting of Jamesonite concentrate has been carried out. The influence of the process conditions such as the smelting temperature, the amount of pyrite cinder (the agent of fixed sulfur) and the amount of additives on the smelting process have been studied. Under the optimum condition the direct recovery ratios of antimony and lead are 83.26% and 68.50% respectively. The ratio of fixed sulfur is 98.97% but more than 15% lead and 30% silver remained in the ferrous matte. The key problem to be solved of this new process is how economical and effective is the recovery of silver and lead in ferrous matte.

Jan 1, 2003

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues which may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Mining Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has now been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff co-operation across the country. MEA has also now commenced some international teaching initiatives which are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual university programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 1, 2009

By Doss H. White

The value of non fuel mineral production in Alabama in 1991 was $539.9 million, a decrease of $20.7 million, a result of the nationwide recession that was felt throughout the State's economy. The 3.7% decline in mineral sales was due primarily to a slowdown in construction, which had a major impact in the construction minerals mined instate. Production and sales of crushed stone and sand and gravel fell significantly below the value reported in 1990. Despite the recession, Alabama moved from 21st to 20th place nationally in mineral value. Mineral industry developments in 1991 were primarily in the metals manufacturing sector. Reynolds Metals Co., Sheffield, celebrated 50 years of operation in Alabama. During the November celebration, the company dedicated a $121 million expansion that included a new casting facility and sheet rolling operation. Gulf States Steel Corp., Gadsden, completed the first full year of operation of its new multimillion-dollar continuous caster.3 The Foundry of the Shoals Inc., Florence, replaced two coke-fired furnaces with electric furnaces.

Jan 1, 1993