Search Documents

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By Germán Rodolfo Ocampo Castillo

El presente texto señala la incrementación de la productividad de la mina Xstrata Tintaya -Antapaccay a través del contrato de personal adicional, donde se reemplace a los operadores titulares durante la hora de refrigerio y asi mantener una operación contínua en la mina. Como consecuencia de ello, se incrementará la cantidad del mineral descubierto en la mina y por ende, el costo unitario de las libras de cobre adicional por operación contínua se reduce.

Sep 12, 2011

By A. W. Khair

This paper presents an analysis of fracture depth and intensity due to subsidence over the longwall panel. Sonic reflection techniques were utilized to determine fracture depth, and a variation of p-wave velocity was used as an indication of the fracture intensity. Instrumentation has been tested for consistency and accuracy first in the laboratory using small scale models, then applied in the field in two mine sites with different mining geometry and geologic conditions. A new sonic viewer was utilized for sonic velocity measurements. Regular hammering method was on acoustic source. The results were concurrent with monitored horizontal strain profiles and measured open fractures over the longwall panels.

Jan 1, 1989

By P. R. Scheller

Reactions between metal and slag are of decisive importance for metallurgical processing. In the continuous casting process, where metal solidifies at the metal-slag interface, reaction products can cause surface defects, with quality damages of the cast products as a consequence. These investigations are focused on the contact area between casting flux and metal. The samples were taken from the mould during the casting process. The results show that layers up to approximately 300 nm from the slag/metal interface represent a specific reaction space. Sodium in this layer on the slag side plays a specific role, which is explained on the basis of experimental results. The transport of oxygen near the interface and the charge transfer is explained on the basis of the ionic character of the slag. The mass transfer rate of oxygen crossing the interface is calculated from measured data, and conclusions concerning the stability of the interfacial tension are made. Keywords: mass exchange, metal slag reaction, interface, ion transport, oxygen transfer, oxidation, casting slag, flux, sodium

Jan 1, 2004

The spatial distribution of copper grades at the Mansa Mina project is highly variable due to the presence of high grade copper/silver/arsenic breccia bodies. Copper grades within the breccia bodies tend to average about 4.5% copper while grades in the surrounding stockwork average about 1.0%. The breccia is known to occur in the vicinity of significant controlling structures, however, the outline and therefore the thickness of the bodies are far from regular. Due to the high grade of these bodies a significant proportion of the value of the project is derived from the breccia tonnages. The irregularity in the outlines/thickness translates into an uncertainty in the breccia tonnage and therefore in the value of the project. Acknowledging the economic importance of the breccia bodies and the risk associated with the breccia tonnage uncertainty, significant additional drilling has been proposed to both understand the spatial distribution of the breccias and reduce project risk. The costs associated with this additional drilling are not inconsequential; thus, a reasonable question is ‘what value is derived from this additional drilling’? To obtain an answer to this important question, a simulation approach is applied. First the deposit is simulated using the existing drilling and the uncertainty in the resource is defined. Next the proposed drilling program is simulated and the simulated data are added to the existing data. Using this expanded data set a second simulation of the deposit is created and once again the uncertainty in the resource is defined. Using this approach, the reduction in the uncertainty in the resource can be determined. To convert this reduction in uncertainty (or reduction in risk) in the stated resource into a dollar value, a method of defining the increase in the project rate of return necessary to account for risk is presented. Using the two different rates of return, the difference in project NPV and hence the value of additional drilling is determined.

Jan 1, 2003

By Dorothy M. Richardson

The Bureau of Mines has participated in the American Petroleum Institute Research Project 48A (API-RP48A) program on the Separation and Identification of Sulfur Compounds in Crude Petroleum. The lack of reference compounds or infrared spectral data has made difficult the identification of individual sulfur compounds boiling above 140° C. The recent acquisition of 24 alkylthiophnnes has made possible a limited study of this important class of sulfur compounds. The infrared spectra of 2-monoalkylthiophenes and 2,5-dialkylthiophenes for the 2 to 15p range are reported. Correlations for determining the 2-alkyl and 2,5-dialkyl substituted thiophenes are derived from this information. The 2-alkylthiophenes show a unique pattern in the 5.50 to 6.54 region, while the 2,5-dialkylthiophenes show a distinctive pattern in the 5.6µ to 6.7µ region. A skeletal vibration occurs in the 9.5 to 10.0µ region for all of the thiophenes investigated. These data will aid the infrared spectroscopist in the identification of compounds of the type reported.

Jan 1, 1961

By P. F. Ledwaba

South Africa?s Northern Cape Province houses a variety of gemstone minerals. Diamonds remain the primary gemstone in the province, but there are also tiger?s eye, sugilite, rose quartz, jasper, amethyst, amazonite, tourmaline, and topaz deposits. This paper gives an overview of the tiger?s eye (TE) mining sector in the Northern Cape, with the objective of assessing the potential of TE to contribute to job creation and poverty alleviation in the province. Mining of TE started in 1803, but gained momentum during the 1960s. Mining is conducted on a small-scale basis, and in most cases without any legal framework. The majority of the residents are not benefiting from TE. It has been reported that an estimated R700 000 to R800 000 worth of TE is leaving the country every week through illegal trading. The potential for TE mining to contribute to socioeconomic development is hindered by illegal operations, lack of technical skills and knowledge, exploitation by dealers, lack of market information, community rivalries, and absence of value addition. A multi-stakeholder approach is needed to formalize the sector and reap the benefits. Mintek is spearheading a TE project in the Prieska area of the Northern Cape, which aims to establish a gemmological centre where TE can be beneficiated into saleable and high-value products..

Jan 1, 2014

By A. R. Byers

"This paper describes the distribution, occurrence, and paragenesis of known sulphide deposits within an area bounded by longitudes 102°00' to 106°00' west and latitudes 54 ° 301 to 57 °00 1 north. The Precambrian bed-rock which outcrops over all but the southern fringe of the area con- . sists of regional metamorphic assemblages ranging from low grade or green schist facies to high grade or amphibolite-granulite facies. The areas . of low-grade metamorphism correspond to 'islands' of volcanic rocks which are surrounded by highgrade paragneisses and migmatites. Intrusive rocks range in composition from ultrabasic to granitic and may be divided into syntectonic and posttectonic sequences. The average composition of the former is granodiorite and of the latter quartz diorite.The massive sulphide deposits fall naturally on basis of mineral content into the following divisions: ( 1) pyrrhotite and / or pyrite, (2) sphalerite and/ or chalcopyrite plus iron sulphides, (3) sphalerite and galena, ( 4) sulphide-bearing pegmatite, and (5) nickeliferous pyrrhotite and / or chalcopyrite. The deposits of iron sulphides are ubiquitous. Ratio of pyrrhotite to pyrite is fairly constant for individual deposits, but their areal distribution appears to be independent of the nature of the enclosing rock and grade of regional metamorphism. All deposits containing ore-grade quantities of base metals have been concentrated at favourable structural locations. Copper-zinc and lead-zinc deposits appear to be associated with syntectonic granodiorite with the lead-zinc concentrations confined to calc-silicate gneisses. Copper-nickel deposits show a close relationship to post-tectonic gabbros and pyroxenites. The paragenesis is more or less the same for the majority of deposits, with iron sulphides and sphalerite being introduced early and followed by chalcopyrite and galena. Some vertical and / or horizontal zoning is apparent in a few deposits. Temperatures of formation and origin of the deposits are briefly discussed."

Jan 1, 1960

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small- scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single- hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Jan 1, 2005

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall. Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls, Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By R. C. Burton

One of the major problems encountered with recirculatory breathing apparatus presently used by mine rescue teams is that the inspired air becomes uncomfortably, and often dangerously, hot. This is also true with self-rescuers. It is well known that man can tolerate very high dry-bulb temperatures if the wet-bulb temperature is low, but not vice- versa. The maximum tolerable, wet-bulb temperature is about 42 °C (108 °F). A continuously inhaled wet-bulb temperature above this value can cause irreversible damage to the throat and lung tissue, and wet-bulb temperatures close to it cause extreme discomfort (1) and seriously retard the capability of the man to perform useful work. A theoretical analysis, combined with experimental results, has shown that it is the carbon dioxide absorbent that is the major cause of high wet-bulb temperatures of the inspired air in the Siebe Gorman Proto 4, and in the Draeger BG 174 apparatus, both of which are used by rescue teams on South African mines (2). In the Proto 4 apparatus, the absorbent for the carbon dioxide is soda lime (calcium hydroxide). The German Draeger BG 174 also uses this absorbent but under arduous conditions such as in hot environments (50 °C, 122 °F), the use of an alkali absorbent cartridge is recommended which consists mainly of caustic soda (sodium hydroxide). Lithium hydroxide is used in some apparatus in the United States. It is clear that different absorbents will produce different quantities of heat and moisture for a given rate of absorption of carbon dioxide. The proportion of this heat and moisture which is transferred to the user depends upon how much can be removed from the recirculating air between the absorbent and the mouthpiece. This paper discusses the present methods of heat removal and describes the design and test results of a prototype evaporative cooler.

Jan 1, 1980

By Terry R. Neumann

The Olallie RARE II study area has volcanic cinder deposits with a sow potential for development. No mining claims or prospects are known within the study area, and except for common construction materials such as volcanic cinders and stone, no mineral deposits were identified. An evaluation of the geology indicates that metallic mineral deposits are unlikely to exist. No significant metallic concentrations were reported in samples from the area. The only resources in the study area are about 30 million cu yds (23 million cu m) of cinders in three cones. The cinder deposits in the study area cannot compete economically with enormous deposits of similar material in more accesible areas closer to markets. At the present rate of consumption, resources outside the area are adequate far into the future. The geothermal potential of the study area is being evaluated by the U.S. Geological Survey.

Jan 1, 1983

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

By Edgardo Torres Hernández

El Proyecto Optimización de Ángulos de Taludes en Explotación de Minas es un proyecto desarrollados por E-Mining Technology (EMT), socio estratégico de Prodimin en Perú, para Codelco Chile en uno de sus yacimientos del Norte de Chile. El desarrollo de este proyecto estuvo enmarcado en el Programa de Proveedores de Clase Mundial; programa que tiene como misión desarrollar un sector de proveedores intensivo en conocimiento, mediante la generación de soluciones tecnológicas empujadas desde la demanda de la minería y desde la propuesta del sector de proveedores que puedan ser escaladas a otros sectores y mercados.

Sep 1, 2017

By D. Harrington

Although the explosion-fatality record for the fiscal year 1944 showed considerable improvement over those of the preceding 4 years, it is still fur from creditable, and the coal-mining industry and agencies interested in the prevention of coal-mine accidents should not be satisfied until accidents from explosions and fires are eliminated. In view of present knowledge of the methods of preventing explosions and fires, such disasters are inexcusable and discredit the mining industry. Despite this knowledge, far too many coal¬mine operators and employees continue to follow procedures that have resulted in disasters in the past. Included in the appendix to this circular are a number of safety measures designed to prevent coal-mine explosions and fires and metal-mine fires. Their adoption is essential if explosions and fires are to be prevented, as certainly they should be. An epidemic of disastrous mine fires of electrical origin during the past 2 years emphasizes the need for better methods of protection of underground electrical circuits. At present, committees of mining-electrical engineers, electrical-equipment manufacturers' representatives, and others are cooperating with the Bureau of Mines seeking means to solve this problem.

Jan 1, 1945

By E. A. Adey, C. Baciu, P. Whitbread-Abrutat, M. Varul, T. Ejdemo, R. K. Shail, F. Wall

Responsible mining requires stakeholder engagement throughout all operational stages and after mine closure. By assessing the current and anticipated future socio-economic and environmental impacts, a company can maximise the positive impacts they can have on a community, whilst minimising any negative impacts. Despite the current emphasis on companies maintaining effective stakeholder relations to gain their ‘social license’ to operate, findings of the present study reveal a wide variation in community expectations, with different degrees of ‘acceptability’ evident across seven sites in Romania (Rosia Montana), Sweden (Kristineberg), the United Kingdom (Cornwall), Bosnia Herzegovina (Vihovici) and Russia (Karabash, Gay and Mednogorsk). These variations reflect the current status of mining within a community, as well as its socio-economic background and the nature of existing engagement with mining companies already operating in the region.

Jan 1, 2011

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By Tracy Brettmann

Equipment ? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2004

By L. Garner McDonald

The U.S. Bureau of Mines tangentially impacted potential coal-cutter bit shank materials against sandstone to investigate the potential of the materials to ignite natural gas by a friction-generated hot streak. The shank material samples were mounted in a 24-in, 550-lb flywheel, which was rotated at surface speeds of 400 to 900 sfpm. The sandstone was advanced toward the rotating flywheel at feed rates of 1 mil per impact. The atmosphere mixture was 7 vol pct natural gas in air. Three grades of polycarbonate resin, an ultra-high-molecular weight polyethylene, and a zinc alloy (ZA27) were among the potential materials. None of these materials caused ignition of the methane at any of the three test speeds (400, 600, and 900 sfpm), but the above materials do not have sufficient strength to hold a carbide tip during coal cutting. Of the materials having sufficient strength to hold a carbide tip, three nickel-based alloys proved less likely to cause a natural gas ignition than did iron-based alloys such as 4340 (a commonly used shank material for coal cutters).

Jan 1, 2010