Search Documents

By D. Z. Wei

Amine collectors with different structures and length of carbon-chain have been widely used in oxide minerals flotation. In this paper, we synthesized one kind of binary amine, N-dodecylethyl- enediamine, and studied its flotation performance. From the results, we can see N-dodecylethylenediamine which has excellent frothability, is a new type of chelating surfactants. And it also has fine catchability to quartz and hematite. The recoveries of quartz and hematite increase with the augment of N-dodecylethylenediamine concentration. When the dosage of collector reaches 100g/t, the recoveries of quartz and hematite achieve 95.30% and 87.89% respectively. Meanwhile, the influence of pH on the flotation recovery of hematite is studied and test results showed that, as pH increases, the flotation recovery rises until pH=9. And the recovery reaches its maximum in alkalescence. The collector has better flotation capability to quartz than to hematite. And the maximum recovery of quartz is gained in alkaline media, which reaches 97.87%. Finally, the flotation mechanism of N-dodecylethylenediamine is discussed through the measurement of infrared spectroscopy.

Jan 1, 2014

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

"The National Mining Hall of Fame and Museum (NMHFM) announced the 2018 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exploration, extraction, management, education and research and development in the U.S. mining industry. Their contributions have had significant and lasting impacts on the mineral and mining industry; these individuals were selected for being mavericks, thought leaders, researchers, educators, mentors, wealth builders and philanthropists.Professor John M. Guilbert, Dr. Leo J. Miller, Robert E. (Bob) Murray and Douglas (Doug) B. Silver will join 240 other mining industry luminaries when formally inducted into the National Mining Hall of Fame on Sept. 29, 2018. Additionally, the Prazen Living Legend of Mining Award will be presented to the Freeport- McMoRan Foundation. The 31st Annual Induction Banquet and Ceremony will be held at the Ritz-Carlton in Denver, CO.2018 National Mining Hall of Fame inducteesProfessor John M. Guilbert was a renowned geologist and professor of economic geology at the University of Arizona; he had a distinguished 50-plus year career in academia and business. Guilbert, together with J. David Lowell, worked on the most important breakthrough in mineral exploration in the last 100 years, the Porphyry Copper Model. This work, known as the Lowell and Guilbert Model, was utilized by exploration geologists worldwide over the next four decades to discover hundreds of millions of tons of copper metal and numerous profitable mines including the prosperous Bajo de la Alumbrera copper mine in Argentina. Guilbert was a founder of The World Museum of Mining in Butte, MT. He was the recipient of countless awards including the Society of Economic Geologists (SEG) R.A.F. Penrose Medal as well as the D.C. Jackling Award from the SME.Dr. Leo J. Miller was a maverick in the mining industry and no armchair geologist. He believed that active fieldwork, on foot with a rock pick, was indispensable for exploration. His basic tenet was to absorb as much information about an exploration target up front, formulate ideas – sometimes novel ones — and then get out into the field to prove those ideas. Miller was known to diverge from the standard interpretation of the geological processes, which formed the mineral deposits, and to apply innovative applications of high-tech tools to more usual exploration programs. This approach resulted in a 50-plus year career that included the discovery of the Kidd Creek massive sulfide deposit and the development of the Lee Creek phosphate deposit; which other explorers had previously given up on, believing whatever phosphate might be present would be too difficult and expensive to mine. The recipient of many honors and awards, Miller received the SME Robert M. Dreyer award in recognition of outstanding achievement in ore discoveries."

Jan 8, 2018

Minerals contribute to the U.S. gross domestic prod-uct (GDP) at several levels?mining, processing and manufacturing finished products. In 2008, the estimated growth rate for the real GDP of the United States was 1.1 percent and the nominal GDP was about $14.3 trillion (Table 1). Trends in various sectors of the domestic economy are often reflected in mineral production and consumption rates. For instance, continued declines in the U.S. housing market during 2008 were reflected in further reductions in the production and consumption of cement, clays, construction sand and gravel and crushed stone (mineral commodities that are used almost exclusively in construction), and those associated with the related manufacture of goods, such as ceramic tile, heating and air conditioning equipment, paint, plumbing and sanitaryware, roofing, wiring and wallboard ? all used by the housing industry. The widespread effects of the slowing domestic economy became more apparent in the last three to six months of 2008 when prices for many mineral commodities declined sharply after reaching record highs earlier in the year, indicating significantly lower demand for those materials or products containing them.

Jan 1, 2009

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences is undertaking a mineral resource assessment study of the Coromandel region, due for completion in July 2000. A key part of the study is the assembly of a geographic information system (GIS), a computerised tool for layering, analysing and presenting spatial information. The GIS is being assembled with ArcInfo/ArcView software and to date includes layers for a digital terrain model, an aeromagnetic map (open file mining company data), a geological map (from the QMAP project), areas of hydrothermal alteration, locations of mineral deposits (GERM database), stream sediment geochemical analyses (REGCHEM database), and a lineament map derived from satellite remote sensing data.

Jan 1, 1999

Unfortunate occurrences resulting in injuries, loss of life, and destruction of property by explosion, fire, and other mishaps during shaft sinking focused the attention of the Bureau of Mines on the need for safety standards For such operations. Information Circular 7810 was published to meet that need. The current revision updates and replaces IC 7810. Several States have some rules and regulations applicable to local conditions, and several Bureau publications (including some now out of print) cover the hazards that may be encountered in shaft sinking. Certain requirements of the Federal Mine Safety Code and Federal Coal Mine Safety Act may be applied, but there are no definite, uniform standards that will guide those desiring to sink a shaft safely and bring about uniform safety inspections.

Jan 1, 1968

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By Nelson Reátegui

El presente trabajo describe los sistemas computarizados utilizados en el centro de operaciones, explotación y beneficio de Hierro Perú, compañía minera localizada en el departamento de Ica. Inicialmente, la función de un sistema computarizado se limitaba a la reducción de costos en la mano de obra y a realizar operaciones básicas en los negocios. Posteriormente, esta situación cambió ya que estos sistemas se utilizan en los niveles de la gestión empresarial.l. Asimismo se explica las aplicaciones de este sistema al comercio, al tipo técnico-científico, así como el cálculo de reservas y el desarrollo del sistema computarizado de performance de equipo.

Nov 20, 1978

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By Ernie Holden, Chris Ringas

In the last 20 years, In Line Inspection (ILI) using intelligent pigs has become the principal tool used by pipeline operators to assess the condition of their pipelines. New pipelines are normally designed to take intelligent pigs, but many older pipelines require some modifications and special procedures for their inspection. This paper is aimed at practicing engineers and managers of pipelines, or people aspiring to those positions. The paper describes the benefits of ILI and some of the practical issues regarding pipeline preparation and cleaning, choice of inspection tool, running pigs in pipelines, and what to do with the data collected. What are the responsibilities of the Pipeline Engineer ? ? Maintain reliable and acceptable performance of the pipeline in terms of safety and product delivery at economical cost. ? Provide a defined margin of safety for operating the pipeline at its designated pressure. ? Provide timely information on all pipeline defects such that repairs can be carried out according to a managed schedule. What Defects does the Pipeline Operator have to cope with ? A useful record of actual incidents seen in pipelines can be obtained from the web site of the US Office of Pipeline Safety (OPS) - http://ops.dot.gov/stats/stats.htm. US pipeline Operators are obliged by Law to report all pipeline incidents exceeding certain threshold criteria (e.g loss of life, escape of product, cost of incident etc). These OPS statistics show that corrosion and third party damage have remained consistently the prime causes of reportable incidents in the US, with similar experience elsewhere. There are several kinds of flaws and defects in pipelines that can lead to failure, the main families being :- ? Metal loss ? Cracks or crack-like defects ? Laminations and other mid-wall defects ? Geometric anomalies

Jan 1, 2006

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By S. Mischler, J. Noll, G. Schnakenberg, A. Bugarski, M. Crum

Diesel particulate filter (DPF) systems and biodiesel fuels are two of the most promising technologies available to the mining industry to reduce the exposure of underground miners to diesel particulate matter (DPM). A study has been conducted to estimate the potential of DPF systems and biodiesel blends to reduce DPM emissions from production vehicles. Results of testing three DPF systems in an isolated zone showed 88% to 99% reductions in elemental carbon concentrations. The test results also show that biodiesel blends, B20 and B50, reduced the elemental carbon concentrations in the mine air by 26 and 48 percent, respectively.

Jan 1, 2004

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962