Search Documents

The New South Wales coal industry is a highly mechanised well organised industry which has developed from an annual production of slightly less than 13 million tons in 1950 to over 33 million tons in 1969. Although continuous miners were not introduced into the mines until 1950, by Jillle 1969 the percentage of coal won by these units was 87.3. The paper describes mining conditions in the various coalfields of the State, their complexities and problems and how these have been dealt with. The introduction of fully mechanised long wall faces has presented a challenge which has been accepted and descriptions of systems in use are discussed. Major expansion of the industry is anticipated to meet the requirements of the growing Australian steel industry, for local power generation and to meet the increasing demands of overseas markets.

Jan 1, 1971

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Strain-induced porosity has been found to occur in titanium and other materials at tensile strains greater than the uniform elongation of the material. Porosity in titanium increases with increasing strain and temperature, being most severe at 300° to 800°F. Strain-induced porosity is believed to be a normal part of the mechanism of deformation in ductile materials. DURING the past few years there have been numerous references to the occurrence of voids in laboratory test specimens of metals subjected to strain.l-7 These voids have been referred to as intercrystalline cracking, strain-induced porosity, intergranular cav-itation, voids, and porosity. They appear to occur at grain boundaries or interfaces, and are generally associated with large amounts of strain and have been found mostly in creep specimens and to a lesser extent in tensile specimens. Because the phenomenon does not occur unless the material has been strained,

Jan 1, 1960

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By D. B. deur Mostert

This paper was presented at the Coloquium on Management Techniques in the Mining and Metallurgical Industry, which was organized by The South African Institute of Mining and Metallurgy and held in Pretoria during June 1988. The author asks whether technical audits are of any use to management. Technical auditing he defines as an evaluation undertaken by an outsider of whether a technical activity is being carried out correctly. After examining the types of technical auditing, and its prerequisites and procedures, he describes its application in regard to quality, and to production processes and their adequacy. He then answers his question by saying that, not only are technical audits very useful, but they form an essential element in the provision of quality products. In addition, they give management the opportunity of testing whether the activities of the organization are being conducted correctly. This is their most important function in that they alert management to areas of potential growth, modernization, and innovation. However, the use to which technical auditing is put remains the key to its value; that is, its value depends on the positive action that each manager takes as the result of a technical audit.

Jan 1, 1989

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common- wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables 'were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1978

By D. Vogt, T. Hattingh

"This paper argues that the technology change to mechanization is also going to require a change in people. It presents a model for technological progress and adapts it to the mining industry. It then goes on to motivate the need for mines to become learning organizations in order to achieve maximum value from their people as they become less labour-intensive. In an important sense, mechanization is as much about knowledge as it is about technology.The change when a mine introduces mechanization or a level of automation is not simply one of technology but also a stage in the development of mining from ‘art’ to ‘science’. ‘Art’ describes a state of technology characterized by tacit knowledge, an understanding that comes only from experience, and has no formal procedures and little structure. In contrast, ‘science’ represents a state of technology where all the component processes are understood in detail, all knowledge is explicit, and processes and structures are formal.Studies of other industries, including metal part manufacture and aviation, show that each stage in the progression from art to science changes the nature of the organization and requires a different mix of skills from the workforce. Perhaps the most important change is the increase in knowledge and decision-making required as the technology gets closer to science.There is anecdotal evidence that South African underground hard-rock mines are not learning organizations. Mines by their nature are capitalintensive with long lead times from investment to returns, so there is reluctance to change from the original plans or to encourage staff to think independently. Particularly as mines move from art to science, this reluctance must be overcome.The important lesson for engineers involved in introducing mechanization is to understand that success or failure will be determined by the people involved, and not solely by the technology. The process will almost certainly require a culture change on the mine. We recommend that the mechanization team includes an expert in human and organizational behaviour to ensure that a receptive workforce and management are in place to accept the new technology when it arrives."

Jan 1, 2016

By Dale S. Hursh, William A. Brooks

Introduction US dependence on external energy sources is dangerous because of unstable political situations existing in key energy exporting countries. So, recent national energy policies call for increased reliance on domestic energy sources. Coal ranks as the most feasible domestic energy source due to its abundant reserves and continental distribution. But to efficiently extract these coal reserves, huge sums of capital funds are needed. Due to the depressed economy, lenders of capital funds are forced to be more stringent with loan applications. This results in fewer loans granted. In many cases, it is uncertain if funding can be obtained. Furthermore, the greatest level of domestic mine financing is expected to be in the coal sector. Demand for capital in the domestic coal industry is anticipated to increase 80% by 1990. The Chase Manhattan Bank in New York warns that these future needs cannot be met by the present capital markets. This article analyzes the current and expected situations of the capital markets available to the domestic coal industry, including: • current and expected future types of financing used in the domestic coal industry; • problems the domestic coal industry may encounter as it seeks capital; and • the future availability of capital funds as concluded from analysis of the first two items. Background Information Regardless of industry, all projects or ventures can be divided into four basic stages: generation; evaluation; selection; and execution. Within the mining industry, one can break down these stages to draw a clear picture of mine development, as shown in Fig. 1. Each successive stage has a corresponding risk level. This risk level defines the type of financing available to the mine operator. Mining Venture Risks A coal mining venture can be characterized by its unique blend of technical and financial risk. As the mine moves through different development stages, varying proportions of each of these risks are encountered. It is these risks that the lender evaluates to determine project suitability. For a coal mining venture, the major complexities generally occur with the technical risk. These include: • quantifying the coal reserves: • assessing the feasibility of the mining method; and • evaluating the design of the wash plant. The reserve risk is gauged by the amount of measured, mineable, and saleable reserves. The greater the latter amounts, the lower the risk. Secure title to the reserves plus title for any surface areas required are also of concern to the banker. Feasibility of the mining method and evaluation of the wash plant design should verify that the project can be completed according to the engineered spec-

Jan 9, 1982

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By F. J. Wiebel

"INTRODUCTION As a result of a general survey of the iron-ore deposits of Califor¬nia, the Bessemer was one shown to offer possibilities of developing com¬mercial ore reserves. Surveying and exploring were done at the request of Congress for an investigation of raw materials for the production of steel.A wartime steel plant has been established at Fontana, San Bernardino County, and a backlog of iron-ore reserve for the maintenance of permanent steel industry on the West Coast will be of National benefit in the postwar period.W. D. McMillan, a mining engineer the Bureau of Mines, examined the property in May 1942, and it was reexamined by D. W. Butner, also of the Bureau, in October 1943. Geophysical work was done by the Bureau in 1944, and the property was explored by diamond drilling from April to August 1944 and February to SeptemberACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contri¬bution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, under the direction of R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests."

May 1, 1947

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By André Brasil

Dado que las represas de relaves construidas por el método de aguas arriba presentan deficiencias relacionadas con los aspectos constructivos y de seguridad, es difícil evaluar la variabilidad real del depósito basándose apenas en los procesos de campo. En ese sentido, el presente texto desarrolla un modelo para describir y simular el mecanismo de formación de las represas de relaves considerando las variables externas (concentración y caudal de descarga) e internas, así como muestra soluciones analíticas y numéricas comparados a nivel laboratorio.

Sep 9, 2007

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987

By G. M. Hutt

Introduction The major development of industrial minerals in Manitoba has been in building materials. 'The building-stone industry is developed far beyond the needs of the Province, and the well known Tyndall limestone is marketed over a wide area throughout the other provinces to Canada. Similarly, gypsum and gypsum products are produced in excess of local requirements and are exported to adjacent provinces. The crushed-stone, sand and gravel, limestone, and lime industries are sufficiently developed to supply the needs of the Province and, notably in the case of lime and lime-stone, there is a surplus for export to the adjacent provinces and to the United States. The manufacture of common brick is well established, but for face-brick and other clay products the Province is dependent largely on importations. Production of silica-sand will increase as Canadian markets become available through recognition of the utility value of the Black Island sand as foundry-sand and for other purposes. There is some possibility of the export of feldspar, of lithium ore and concentrates, and perhaps of salt. A considerable part of the Province has not been seriously prospected for industrial minerals and it may be expected that, as time goes on, other deposits of non-metallic minerals will be discovered and opened up, especially as the prairie provinces become more industrialized. At the present time, there is some activity in the southern part of the Province based on gas and oil indications. Whatever may be the outcome of this work, it should yield valuable information concerning the geological structure of the area.

Jan 1, 1934

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By R. M. Owens, J. F. Lupo

The Shirley Basin Uranium mine, located in southeastern Wyoming, USA, was an open pit mining operation consisting of a series of several open pit mines excavated into poorly consolidated sandstones, siltstones, and claystones. Since the initial open pits were developed in 1969, slope failures have plagued the mine and mining operations. These slope failures have persisted into the current mine reclamation period. When the mine was first developed, the open pit slopes were designed to range between 45 to 55 degrees. Numerous slope failures during mine development required the pit slopes to be redesigned with slopes as shallow as 26 degrees. At present, movements are occurring within the open pits on reclaimed slopes that are shallow as 12 degrees. Several detailed slope studies were conducted at the mine in the early 1970s. These studies, combined with more recent geotechnical investigations, provide a unique detailed history of pit slope failures on shallow slopes. This paper presents an evaluation of the slope failures at the Shirley Basin mine, highlighting important mechanisms causing slope failures on very shallow slopes. The evaluation demonstrates important key parameters for shallow slope design.

Jan 1, 2001

By A. Lyndon

Combined loading tests are described to three 1.2m diameter cast-in-place bored piles, 12m long, formed through cohesionless material into stiff sandy clay. The maximum loading conditions imposed at the pile head were 2400 kN vertical, 160 kN lateral and 3120 kNm in bending, corresponding to twice the working load. Settlements, deflections and rotations of the piles were measured during the tests. An interesting finding which the test results suggest is that, in the short term, vertical movement had apparently no marked effect on lateral performance for piles working at design loadings.

Jan 1, 1989