Search Documents

By A. J. MOORE

When the writer first saw the square-set timbering, he was at once impressed with the fact that the frames made by the sets, along the lode and across it, were composed of panels with rectangular openings, and it was puzzling to understand howsuch a collapsible construction could resist pressure that came unevenly on it. Later he learnt that the sets did not satisfactorily resist such pressure, but mullock filling had, to a great extent, to undertake this duty for them. So it appeared that the setswere practically an expensive scaffolding, enabling the miners to work in the face and carry the stope forward, till the filling was put in behind them to take the pressure of the roof and sides of the excavation. Of course some of the pressure is takenby the sets, but this is because "the set timbers prevent the filling being done perfectly; if it were practicable to remove the sets before filling, the filling by itself would more effectively support the back and wall, than do the combined sets andmullock. On the whole, therefore, the sets can hardly be said to be of much benefit where pressure has to be resisted. Despite this, the system has been of immense service in mining wide lodes, but for all that, it can only be pronounced a makeshift.This is no reflection on Deidesheimer, the famous originator of the square set, for, as will be shown later on, this way of...

Jan 1, 1912

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007

Underground coal mining continues to evolve in the U.S., and more reserves are being mined under deeper cover, with worse roof, or with interactions from previous workings. At the same time, the mining community is responding to higher safety standards and intense competitive pressures. The need for effective ground control design has never been greater. Ground control safety issues that have been addressed by recent the National Institute for Occupational Safety and Health (NIOSH) research include: Improving roof support performance; Maintaining safe tailgate escapeways from longwalls; Optimizing pillar design for retreat mining; Controlling multiple seam interactions; Predicting roof conditions during extended cuts, and; Preventing massive pillar collapses. As funding from both government and the private sector has diminished, the emphasis in research has focused on providing the mining community with practical techniques for improved ground control design. Many projects have successfully employed empirical methods that emphasize the statistical analysis of case histories from underground mines. Other projects have employed numerical models and large-scale laboratory testing of roof support elements. Using these data, NIOSH has developed an entire toolbox of computer programs that have been effectively transferred to the mining community.

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

By Víctor De la Cruz

Dado que la mina Rosaura (Lima) se dedica a la explotación de minerales polimetálicos como el zinc, plomo, cobre y plata, la caracterización geomecánica de su estructura, morfología y reservas demostró una tendencia hacia los métodos masivos -en tanto presenta ventajas técnico-económicas comparativas frente a otros posibles métodos como el corte y relleno y conjunto de cuadros. Por ello, el presente texto describe el método de “Hundimiento por Subniveles” (Sub Level Caving – SLC), como el más indicado. El SLC se basa en la utilización del flujo gravitacional del mineral fragmentado a través de la perforación, voladura, y el hundimiento de la roca estéril principalmente de la caja techo. El diseño del elipsoide de extracción determinará la ubicación de los Sub niveles y Drawpoints, los cuales serán críticos para hacer rentable el minado, de forma que los beneficios actuales del método indican niveles altos de Seguridad, recuperación alta de mineral, bajos costos y mejora constante de la productividad.

Sep 9, 2007

COMPRESSED air is held in high esteem by the mining engineer as a medium for the transmission of power. The transmission, however, is accompanied by a high percentage of loss. Of the total work done by the steam cylinder'in compressing the air inthe air cylinder, less than 50% is ultimately utilized by the machines underground. These losses are due to its essential and inherent properties as a gas. One of the sources of loss is that due to transmission through the pipes which distribute the air from the receiver to the various places where it is used. As the capacity and economic design of air-compressing plant are influenced by this source of loss, it may be of interest to give an outline of how estimates may readily be made'in practice of thediameter of pipes, quantity of air discharged, and the drop in pressure occasioned.In hydraulics we have a general formula given M Rankine's "Civil Engineering" :It was suggested, the writer believes, in the first instance by D'Arcy, that this formula could be made to apply to an elastic...

Jan 1, 1918

By M. W. Lewis, J. Werner

Fluctuating metal prices, declining head grade, and increased operational costs are forcing many open pit mining companies to look to their balance sheets for significant cost reductions in order to remain competitive. Maintenance continues to represent a significant proportion of the total operating costs in the mining industry. Compared with the other major cost components of the mining process, very little effort has gone into maintenance optimization. The potential payoff from maintenance optimization on the cash cost of the commodity is enormous. A large percentage of these costs are incurred in unscheduled maintenance events, which typically cause serious disruptions to the production process. These maintenance-induced production losses can be a significant contributor to the overall operating costs. A structured proactive maintenance approach using the latest advances in technology can achieve dramatic cost reductions and productivity improvements. Remote condition monitoring systems are becoming increasingly commonplace and have the potential to identify problems prior to failure. Detection of equipment degradation prior to failure will enable repairs to be scheduled thereby reducing costs and interruptions to production. Remote condition monitoring technology has evolved rapidly in recent years, with a host of new tools becoming available to assist mine operators in improving their maintenance operations. These tools have capabilities such as remote real-time vital signs and performance monitoring, alarm/event handling, trend analysis, and maintenance workflow management. When these monitoring tools are used in conjunction with a mine management system, the vital signs data can be integrated and associated with maintenance history, predictive maintenance data, operational information, and geographical information. This integrated approach to the management of vital maintenance data will help shift the mobile equipment maintenance paradigm from reactive to proactive. This paper will introduce a proactive approach to the management of the maintenance process and the tools required to facilitate this process.

Jan 1, 2005

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Forrest T. Moyer

Frequency rates of injuries per million man-hours of exposure were improved during 1965 slightly to moderately over those of 1964 at metal mines, nonferrous reduction and refining plants, nonmetal mills, stone quarries and mills, sand and gravel operations, and slag operations. However, at metal mills and nonmetal mines the rates of occurrence of work injuries were less favorable. The severity rates of injuries during 1965 were better than in 1964 at metal mines and mills, stone quarries and mills, and slag operations. Conversely, severity rates were worse at nonferrous reduction and refining plants, nonmetal mines and mills, and sand and gravel operations.

Jan 1, 1966

By G. T. Lineberry

Underground mine development begins with the positive investment decision to mine and ends with the inception of full-scale exploitation. It incorporates all activities, personnel, and equipment required for creation of underground access to a mineral deposit. Because of the depletion of near-surface mineral resources, the reduced mobility of large surface mining equipment, increasingly stringent environmental constraints, and the introduction of promising innovations to rock penetration and rock excavating equipment (e.g., continuous miners, rock borers), under-ground mining is projected to account for an increased share of worldwide mineral production in the foreseeable future. Without proper engineering during the mine development phase, failure of the underground mining project is axiomatic. A frustration attendant to coverage of the complex area of underground mine development lies not only with the need for treatment of the many disparate specialties within the area but even with the lack of systematization of these specialties in what is recognized as a vital precursor to successful mining. Section17 offers insights into (1) the basic principles of the planning and design process, including baseline assessment, reserve determination, premine planning, and subsystem design (Chapter17.1); (2) equipment selection and sizing, with emphasis on exca-

Jan 1, 2008

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Lawrence W. Gubbe

Air blast associated with detonation of explosives in mining, construction or military applications is often responsible for complaints by people who live or work in the vicinity of the activity. Most often, the complaints are based on the perception that vibration caused by the airblast damaged one or more residential buildings that may be located within several hundred feet or several miles from the blast site. The potential for airblast to cause damage is related to the amplitude and frequency of the airblast overpressure wave at the receptor. Amplitude and frequency of the overpressure wave are, in turn, dependent upon the type and amount of explosive detonated; the degree of confinement; the distance the wave travels; the topography between the blast site and the receptor; and, atmospheric conditions. It is well known that, as the result of atmospheric focusing, the amplitude of airblast overpressure that exists relatively far from the blast site may be substantially higher than the amplitude associated with the attenuated wave in an isotropic atmosphere. Two methods are available to predict baseline overpressures 1) the Sandia Laboratories, Atomic Energy Commission method as extended by the Naval Ordinance Laboratory (NOL method) and the Ballistic Research Laboratory method (BRL method). These methods are developed by different techniques, are based on different idealized atmospheres and predict widely different results. The amplification factor applied to account for the effect of focusing must be consistent with the method used to predict the baseline overpressure. Theoretically, the amplitude of the overpressure at distances several miles from the blast site could be more than 25 to 100 times the amplitude of the attenuated wave predicted by the BRL method. However, based on comparisons with measured overpressure data is probably less than approximately 3 times the amplitude of the attenuated wave as predicted by the NOL method. This paper is based on research conducted as part of investigations of airblast damage complaints associated with an accidental explosion near Eveleth, Minnesota and with the disposal of military explosives by detonation at the Sierra Army Depot near Herlong, California. The techniques available for estimating the airblast overpressure that might be generated at various distances from the blast site and criteria for evaluating the potential for damage are examined.

Jan 1, 2004

By R. D. Williams

In spite of the increasingly polarized and politicized view of climate science and climate change in the United States, many of the principles behind the ?theory? of Anthropogenic Global Warming (AGW) or Global Climate Change (GCC) are in fact firmly established both in fundamental physics and detailed observations and are widely accepted elsewhere. The discovery of the earth?s ?greenhouse effect? dates back nearly 200 years to the work of French mathematician and physicist Joseph Fourier in 1824 and 1827. In 1872, John Tyndall an English physicist and mountaineer, described the capacity of various gasses to absorb radiant heat. He identified water vapor and carbon dioxide as the principal ?greenhouse? gasses. The work of Fourier and Tyndall was the foundation for the theory that increasing carbon dioxide (CO2) in the atmosphere might be responsible for an increase in global temperatures developed by the brilliant Swedish chemist Svante August Arrhenius in 1896. This was backed up by the additional work of Gilbert Callendar in the 1930s, and Gilbert Plass, Hans Suess and Roger Revelle in the 1950s. There is little scientific dispute about the physics by which this occurs: carbon dioxide in the atmosphere absorbs long wave radiation that would otherwise escape into space, thus warming the lower atmosphere and respective temperatures worldwide. The Intergovernmental Panel on Climate Change (IPCC), approximately 2500 climate scientists from around the world, has concluded that increases in carbon dioxide resulting principally from the burning of fossil fuels are responsible for most of the continuing increases in global temperatures (IPCC, 2007). NASA?s Goddard Institute for Space Studies (GISS) states; ?The ten warmest years all occur within the 12-year period 1997-2008? (GISS, 2009). 2009 was the second warmest year on record and 2010 was tied with 2005 for the warmest year on record (GISS, 2010, 2011). The science is in fact settled; the earth has not cooled since 1998 as some have claimed. It continues to warm as evidenced by not only surface temperature records but also ocean temperature records as well as changes in physical and biological systems (IPCC, 2007).

Feb 27, 2013

The uptake of nickel into the lattice of pyrrhotite, Fe1 _1J S was studied experimentally in the temperature range 200°C to 760°C. Nickel from both aqueous solutions and salt melts diffuses rapidly into the sulphidelattice with an accompanying release of iron into the solution or melt. The rate of uptake of nickel and its diffusion into the sulphide lattice were followed by optical microscopy and by analysis with an electron probe microanalyser. Some geological consequences of this phenomenon affecting the distribution of nickel in rocks associated with nickel-iron sulphide ores are discussed.

Jan 1, 1972

By P. Koh

A novel approach incorporating computational fluid dynamics (CFD) and flotation modelling has been used for investigating flotation cell designs. CFD modelling has increasingly been employed to enhance understanding of the cell hydrodynamics in mineral and coal flotation. Opportunities for improving the flotation cell performance can be identify by modelling. The CFD-flotation model from CSIRO incorporates cell hydrodynamics that affect particle-bubble interactions. Information from the model includes velocities, turbulent dissipation rates, gas hold-up, particle-bubble attachment and detachment rates. The attachment and detachment rates have been found to be effective measures of cell performance for cell design.

Jan 1, 2011

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

By T. C. Wesson

The need for elemental-analysis information on coal mine dust for use in health and safety research prompted this study by the Bureau of Mines. Neutron-activation and X-ray fluorescent techniques were used to obtain five-element analysis (silicon, aluminum, iron, calcium, and magnesium) on 444 samples from 68 coal mines in 10 States. From these analyses, the average composition of the dust in coal mines was determined. The contribution of the primary dusting material (limestone dust) to the makeup of coal mines was shown. Regional differences in mine-dust composition were indicated.

Jan 1, 1974