Search Documents

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By S. J. Rodgers

This report presents the results of in-mine studies to determine the severity of dust sources in conventional mining operations. Three underground coal mines were surveyed using gravimetric samplers and GCA RAM-1 continuous dust monitors. Two additional mines were surveyed using only GCA RAM-1 monitors. Data on dust control methods were acquired during the survey, also. The results indicated that cutting/drilling and loading out were the dustiest operations during a conventional mining cycle. Roof bolting, shot firing and product transport were less severe dust sources.

Jan 1, 1983

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By C. R. Copeland

Airborne dust emission standards are receiving growing attention. This trend is motivated by significant health studies that have shown adverse health effects due to exposure to dust. Currently, the air quality standards are not specific to particles in the nanoparticulate range (<1,000 nm). However, as our understanding of health related matters increases, it is very likely that nanoparticulate standards will be adopted. It was previously believed that typical comminution and material-handling practices could not result in airborne nanoparticulates. However, experimental studies using air monitoring and SEM have verified the presence of nanoparticulates in the air as a result of comminution and material handling. This means that emerging nanoparticulate air quality standards are a real possibility for industrial operations. With this emerging problem facing the minerals industry, effective suppression methods for nanoparticulates should be explored. Systematic studies have indicated that nanoparticulates from silica can be suppressed utilizing hygroscopic reagents such as calcium chloride. This reagent was as much as 93% more effective than water in suppressing silica nanoparticulates.

Jan 1, 2007

By A. Abdollahi

Modification of the silicon in Al-Si alloys can be performed by adding a very small amount of some elements like Na, Sr and Ca to alter the form of silicon from an acicular shape to a fine fibrous one. This modification results in a considerable improvement in mechanical properties especially elongation, Metallographic observations in A356 alloy indicated the degree of the modification with Na, Sr and Ca, They showed that the effect of Ca as a modifier is not as strong as is Na or Sr while Na is the most effective modifier, Although modifiers improve mechanical properties, they also increase porosity in castings, The reduced pressure test (RPT) and Tatur test showed that the increasing porosity with Na is the most and with Sr is the least.

Jan 1, 2004

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

E. W. Stutchbury (Internationa~ Oombustion Aust. Ltd.) : Mr. Callcott made particular mention in his paper of erosion in primary air fans which are placed after the mill discharge. He adds that subsequent reduction in plant performance and resulting increased maintenance costs occur. It is generally assumed that this statement is substantially correct as the fan handles the complete output from the mill, but with modern materials, reduction in performance and subsequent .maintenance are not now a problem. This consideration of handling the pulverised coal in the fan is more than offset by the advantage of operating the mill under suction which results in cleaner operating conditions, simpler feeder arrangements and elimination of complicated seals on the mill.and feeder unit. It should be specially noted that whereas mill exhausters in the past have used chequer plate blades (sometimes with the addition of hard facing by electrode deposit) it is modern practice to provide fan blades of up to 1 in&#183;. thick Ni-hard suitablyheat treated, with the circumferential section of the fan also in Ni-hard. By the use of this material large power...

Jan 1, 1957

Certain information contained herein regarding Champion Minerals Inc., including management?s assessment of future plans and operations, may constitute forward-looking statements under applicable securities law and necessarily involve risks, including but not limited to risks associated with mining exploration, operating costs, production costs, volatility of share prices, currency fluctuations, imprecision of resource and reserve estimates, environmental risks and ability to access sufficient capital from internal and external sources. As a consequence, actual results may differ materially from those anticipated in any forward looking statements. Plans, intentions or expectations disclosed in any forward-looking statements or information should not be read as guarantees of future results or events, and will not necessarily be accurate indications of whether or when or by which such results or events will be achieved. Except as required by law, Champion Minerals Inc., expressly disclaims any intention and undertakes no obligation to update any forward looking statements or information as conditions change. The historical mineral resources mentioned are strictly historical in nature and are non-compliant to National Instrument 43-101 mineral resources and mineral reserves standards, and should therefore not be relied upon. A qualified person has not done sufficient work to upgrade or classify the historical mineral resources as current National Instrument NI-43-101 compliant.

May 1, 2011

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By R. A. Beall

This paper summarizes the development of a furnace for producing titanium castings. The general problem is outlined and chronological details are given on the construction and operation of four different casting furnaces, all utilizing consumable-electrode arc heating and water-cooled copper crucibles. Of the two methods of pouring, the tilt-pour technique has been more satisfactory than bottom tapping. Mold design, electrode fabrication, and deep-pool production are discussed. INTRODUCTION In the early summer of 1953 the Bureau of Mines was contacted by the Department of the Army through Watertown Arsenal to explore the possibility of conducting research on casting titanium metal. The objective of the program was "to develop a technique for producing formed castings of titanium metal not less than 40 pounds in weight and without introduction of deleterious contamination."

Jan 1, 1956

By J. Forwood

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the project&apos;s gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the Lenders&apos; and Borrower&apos;s teams has facilitated a greater understanding and `ownership&apos; of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

Who Macraes Mining Company Limited is can be summed up by the following statements: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; We have been New Zealand&apos;s largest gold producer for seven years +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; We have one of the lowest market capitalisation per reserve ounce of the gold producers in the &nbsp;Australian Gold Index +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; We have a resource finding cost of less than NZ$l0 per ounce +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; We have a large land bank with proven reserves +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; We have an Operating Cash Margin of approximately NZ$200 per ounce +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; We have reduced our Dry Milled Tonne Cost by 34% since 1992 &nbsp; Our Mission is to continually grow our gold business, through maximising cashflow and focusing on our value drivers being: +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Increasing reserves +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Increasing cash operating margins +&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp; Increasing production &nbsp; The real challenge is the reduction of operating costs and the optimisation of revenue, particularly in the current gold price environment. &nbsp; The Company has as at 31 December 1996 total mineral resources of 6.1 million ounces and reserves of 3.4 million ounces. This together with our current cash position of approximately NZ$15 million and strong hedging book of approximately 800,000 ounces places the Company on a sound financial footing whilst positioning itself to aggressively pursue its growth strategy when gold price and market conditions improve.

Jan 1, 1997

By Raymond A. Binns

The Eastern Manus Basin (EMB) contains three major active hydrothermal zones and a number of smaller occurrences of hydrothermal deposits, and can be considered as a regional-scale modern analogue for volcanic-hosted mineral fields on land. Unlike the central Manus Basin, a back-arc spreading zone with some MORB-like basalt-hosted massive sulfide deposits, the EMB is a pull-apart rift zone between two transform faults, where a basement of Eocene-Oligocene arc crust is being thinned by extension, with rapid sedimentation on the tilted fault blocks. Present-day submarine igneous activity in the EMB, with which hydrothermal activity is associated, has arc geochemical affinities and is related to subduction of the Solomon Sea Plate at the New Britain Trench. Overall, hydrothermal deposits in EMB are found with lavas ranging from picritic basalt to rhyodacite in composition, although the two major occurrences of massive sulfide are hosted by the more siliceous dacite and rhyodacite variants. Some volcanic edifices are central eruptions, mostly of porphyritic lavas or domes, while others are elongate ridges formed by fissure eruption in which the typically aphyric lavas were very fluid. Evidence for shallow-level fractional crystallisation controls of lava chemistry implies presence of subjacent differentiated intrusions or former magma chambers. Seismic tremor at one site during the nearby 1994 Rabaul eruption suggests magma movement in the chamber.

Jan 1, 1998

By W. J. Fene, R. D. Currie

The value of protective clothing in the prevention of injuries has long been recognized in many of the leading industries , but the adoption of the idea into mine safety programs is comparatively new . Once started , however , the idea has grown rapidly and the results already obtained by mining companies have shown that it is fundamentally sound . Both coal and metal mining companies are rapidly adopting these protective measures , and since 1924 many mines have become well equipped with eye , head , and foot protection . At the present time approximately 70 percent of the employees in the anthracite mines of Pennsylvania are provided with safety hats . At many metal mines all employees are provided with safety hats, shoes , and goggles . The Pennsylvania mining law provides that all shaft · workers in anthracite mines shall wear protective hats . In According to a study³ made of the nature of 3,485 temporary injuries and of the parts of the body of underground coal mine employees most exposed to occupational hazards , the head and face were injured 665 times , the hands 856 times , and the feet 565 times . Of 2,555 temporary injuries in metal mines , the head and face received 484 , the hands 788 , and the feet 357 . a similar study4 made by a coal -mining company for the year 1928 , of 556 injuries the scalp received 9 , the skull. 4 , the eyes 47 , the hands 62 , the thumbs 21 , the fingers 141 , the ankle , the feet 51 , and the toes 35 . Probably most of these injuries could have been prevented by suitable protective clothing and equipment . This study also revealed that at least one injury occurred

Jun 1, 1933

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page Information Circular entitled "Mineral wool." This was one of the first publications to present to the public some technical aspects of the mineral-wool industry. Since that time several articles have appeared on the subject in the technical press as well as publications by State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large numbers, and in 1935 it was decided, with the cooperation of the is industry, to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for public distribution. As a first step, a brief questionnaire was mailed to the known producers asking if they would cooperate for publication. Favorable replies were received from of percent of the manufacturers, and the field work was started. As the study progressed and tie number of plants visited grew, it became more and more apparent that the industry had made rapid strides in technical operation and control of their product, as well as in increasing production during the mast decade.

Jan 1, 1938

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau&apos;s Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists&apos; Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950&apos;s; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962