Search Documents

By John L. Ellenberger, Gabriel S. Esterhuizen

Observations of pillar conditions in limestone mines showed that the presence of weak bands in the limestone can result in pillar damage at stresses that are lower than one would otherwise expect. The objective of this National Institute for Occupational Safety and Health study was to investigate the mechanism of failure caused by the presence of weak bands by using a series of numerical models based on realistic physical properties. The effect of the weak bands on pillar strength was also investigated by developing a series of pillar models with different width-to-height ratios and determining their strength by simulating a servo-controlled loading condition. The material properties of the bands and the limestone were varied and their effects on pillar strength were determined. Model results demonstrated failure development similar to the pillars observed in the field. The weak bands were seen to develop tensile stresses in the limestone as they extrude under increasing stress. The limestone fails in tension at a much lower stress than its expected uniaxial compressive strength. The results showed the load bearing capacity of the pillars can be reduced significantly by the presence of multiple thin weak bands. The degree of strength reduction is largely dependent on the compressive strength, the frictional resistance and the thickness of the weak bands. Single weak bands do not affect pillars as severely as multiple bands. However, the model results show that a single thick weak band, which comprises more than about 2 percent of the pillar height, can cause a significant reduction in pillar strength. The weakening effect of the bands become less severe as the pillar width-to-height ratio is increased. Field observation of spalling and failure associated with weak bands in limestone pillars show that the failure mechanism in the models resembles the observed failure. The model results provide insight into the important factors affecting pillar strength in the presence of weak banded materials.

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

On June 20, 1972, Ocean Energy was awarded Contract No. H0220055, entitled Portable Task Luminaire System Development. Initially, this was a 12 month program consisting of three phases: Phase I -- Design of the Luminaire System and Battery Chargers, Phase II -- Fabrication of Prototype Units, Phase III -- Fabrication of Production Prototype Units and Battery Chargers. In addition to developing the Portable Task Luminaire System, however, this contract was amended a number of times in the course of the program to include the development of a Low Coal Portable Task Luminaire, a Rib Mounted Luminaire System, and a Machine Mounted Luminaire System, all based upon the same high frequency fluorescent lighting and safety technologies involved in the Portable Task Luminaire. This report covers the activities of this program as amended, and includes the development and fabrication of all of the systems. This report constitutes the final fulfillment of the contract.

Jan 1, 1974

Australia's iron ore industry is entering a challenging period with the development of new orebodies, the introduction of new products and the push for further downstream processing. In addition, the recent price reductions for iron ore exports have intensified the focus on reducing capital and operating costs. To assist in these areas, CSIRO is expanding its research capabilities, including the incorporation into CSIRO of the Mineral Processing Laboratories in Perth, which were previously managed by the WA Department of Minerals and Energy. In addition, a large part of the $24.4 million expansion of CSIRO's Pinjarra Hills laboratories in Brisbane will be devoted to enhancing iron ore processing research, providing purpose built laboratories and large process bays.

Jan 1, 1999

By Andy Fortin, André Vien, Christophe Bouché, Jeff McKay

"The technology and equipment design of the Twenty-first Century permit us to exploit low-grade ore bodies with milled tonnages reaching 300,000 tpd. Because of their substantial operational costs (energy, wear parts, etc) and precarious economic situations, the operations of today must maximize their metallurgical performance.The implementation of an Expert System becomes a logical avenue to pursue in view of increasing plant performance.Many operations, following the implementation of an Expert System, meet the objectives they determined before its integration; such as increased tonnage, stability, decreased costs, etc. However, they often cannot develop the full potential of the system due to certain factors that have been neglected or omitted during the implementation of the system.Three main elements have been identified during the implementation phase at INMET Mining Troilus Concentrator: 1- Instrumentation & Control 2- Software 3- Integration. Even though they have been clearly identified, these elements are often neglected due to lack of resources or lack of comprehension on the part of the operations personnel. This document will demonstrate, based upon our experience at Troilus and that of Metso Minerals, that we can identify and handle many factors which influence the profitability of the Expert System, for both short and long-term process control improvements.INTRODUCTIONThe Inmet Troilus Mine is an open pit mine, situated 175 km north of Chibougamau in the province of Québec, Canada. The mill, which started production in November of 1996, was originally designed to treat a gold – copper ore at a rate of 10,000 tpd.In early 1998, the mine plan called for a pit pushback and decreasing head grades for the following two years. With the price of gold nearing decade lows, the Troilus project was facing a major economical setback. There was a sense of urgency to reduce operating costs below the market price of gold. The mill team presented a project to management calling for an increase in mill throughput while minimizing capital expenditures and operating costs. This idea was supported by the existing mine plan, which called for a mine cut-off of 0.7 g/t Au and stockpiling low grade 0.5 g/t material for future milling."

Jan 1, 2003

? Develop a six year capital budget for future emission controls at Western Springfield Power Plant that would provide long-term operating certainty

Jan 1, 2005

By S. C. Tennant, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Immobile-element lithogeochemistry is providing a detailed chemostratigraphy of the submarine Ordo-Silurian volcano-sedimentary sequence. Primary lithologies and magmatic affinities of the sericitised and silicified volcanics are determined from binary plots of Nb, Zr, Y, TiO2 and Al2O3, while mass-change calculations using immobile-element anchors can identify and quantify zones of significant hydrothermal alteration. Stratiform polymetallic mineralisation at the western margin of Parys Mountain, around the Penymynydd fault zone, has been shown to have a distinct hanging-wall and footwall stratigraphy. These ore zones are probably part of a homoclinal, north-younging volcano-sedimentary sequence. The apparent stratigraphic complexity results from primary lithofacies variations and pervasive alteration, with the modifying role of the Caledonian orogeny much less than previously suggested

Jun 19, 1905

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By L. J. E. Hofer

THIS BULLETIN analyzes and summarizes research at the Bureau of Mines dealing with the preparation, properties, and reactions of iron carbides in the period 1948-60, part of which was sponsored by Wright Air Development Laboratories. The objective was to develop better catalysts for the synthesis of methane and higher hydrocarbons from hydrogen and carbon monoxide. The investigations resulted in the first adequate characterization of epsilon iron carbide, which later proved to be an important intermediate in the tempering of martensite in steel. At temperatures near 170° C, the carbon in carbon monoxide reacts nearly quantitatively with finely divided alpha iron to form an iron carbide in which the metal atoms occupy the positions of the close packed hexagonal arrangement with lattice parameters of ao=2.754 A and co=4.349 A. The carbide has a composition within 2 atomic percent of that required for the formula Fe2C, a Curie point of about 370° C, a specific magnetization of 160.4 ergs per gauss-gram Fe at 50° C, and a ferromagnetic moment of 1.70 Bohr magnetons. Epsilon iron carbide can be converted to chi iron carbide by thermal treatment at 343° C for about 70 hours. The chi iron carbide so formed has a Curie point of 247° C, a specific magnetization of 142.5 ergs per gauss-gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 5.5 Bohr rnagnetons per iron atom. Direct synthesis of this carbide from carbon monoxide at 240° C indicates a composition within 7 atomic percent of that required for Fe2C. Chi iron carbide can be converted to cementite at 550° C in about 315 minutes. The theta iron carbide so prepared has a Curie point of 210° C, a specific magnetization of 147.3 ergs per gauss gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 3.9 Bohr magnetons per iron atom. Pure chi iron carbide reacts to form theta iron carbide by the elimination of free carbon. In the presence of an excess of free iron in intimate contact with the carbide, chi iron carbide reacts with the free iron to form theta iron carbide. The second reaction proceeds at an appreciable rate at 320° C and can be used to snythesize finely divided theta iron carbide with no free-carbon impurity at low temperatures. The ease of the reaction in the presence of free iron suggests that chi iron carbide is an intermediate in the tempering of epsilon iron carbide to theta iron carbide as it proceeds in steels. Experiments on carbon steel show that the magnetic moment of the iron atoms in martensite is about 2.2 Bohr magnetons per atom, a value approximately the same as that of the iron atoms in alpha iron. The Curie points of epsilon iron carbide, chi iron carbide, and theta iron carbide were found -in various specimens of tempered steel to be 10° to 20° C lower than normal values. This shift is probably the result of manganese in solid solution. Preparations of various compositions of epsilon iron carbonitrides show many effects of extensive isomorphism between epsilon iron carbide and epsilon iron nitride. The action of carbon monoxide on finely divided alpha iron at 400° C results in free carbon deposits containing filaments about 0.1 micron in diameter and several times as long. The filaments are characterized by nuclei of dense material located midway from each end of the filament. Although carbiding to near completion at 240° C over periods of about 300 hours produces a preparation containing no appreciable percentage of epsilon iron carbide, very brief periods of carbiding of the order of a minute result in the formation of detectable epsilon iron carbide even at temperatures as high as 325° C. The data indicate that epsilon iron carbide is an intermediate in the formation of chi iron carbide during its formation from carbon monoxide in the gas phase. Attempts to convert cementite to chi iron carbide by cold work increased the Curie point but did not change the X-ray powder diffraction pattern.

Jan 1, 1966

By Maya Kamenetsky, Khoi Nguyen, Natalee Bonnici, Steve Walters, Claire McMahon, Julie Hunt, Ron Berry

"The analysis of meso- and micro-scale textural attributes has been undertaken on ore samples from the Ernest Henry iron oxide-copper-gold (IOCG) deposit in NW QLD. Quantified textural data including grain size, shape and mineral association have been extracted from classified images of core with the aim to better predict potential mineral processing behaviours such as comminution, liberation and flotation. Data have been extracted from images of intact core at meso- and micro-scales using high resolution continuous images collected using automated core-logger technology, SEM-based and optical microscopy platforms.The results of this study will show examples of quantified size, shape and mineral association data from meso- and micro-scale classified images. Analysis of the data shows that there are domains of variable grain size and mineral association that can potentially be related to crushing and liberation behaviour. The trends that are observed at the drill-core (meso-) scale are consistent with those at the micro-scale. The results from the micro-scale analysis show that the domains defined at the core-scale have clearly different chalcopyrite sizes and shapes as well as variable bulk mineralogy.INTRODUCTIONInnovations in technology have allowed automated extraction of information about mineral shape, grain size and mineral association, i.e., texture, from meso- and micro-scale images of intact rocks. The overall aim of this research is to investigate trends in quantified textural data that can potentially give an early view of processing parameters such as predicted grind size and liberation behaviour."

Jan 1, 2009

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By Terry McMahon

This Bureau of Mines report describes the rock burst problem and measures being taken for its alleviation in the deep underground mines of the Coeur d?Alene Mining District in northern Idaho. The geologic features that contribute to rock bursting in that area are discussed and briefly compared with similar features in other burst-prone mining districts throughout the world. Early investigations to understand and control rock bursting are reviewed, and the mechanics of bursting are discussed in terms of the seismic events that produce them. Sources of strain energy, rock failure mechanisms, and the conditions necessary for the release of seismic energy are covered in detail. Rock burst research in the Coeur d'Alene District is described. Included are discussions of the microseismic method as both a research tool and as a rock burst monitoring system, rock destress blasting and preconditioning methods for rock burst control, and stoping methods currently being developed to reduce rock burst hazards.

Jan 1, 1988

By Edward A. Barrett

The ability to recognize visual cues commonly associated with roof and rib hazards is fundamental to the prevention of groundfall accidents. The perceptual skills that miners possess to visually search and assess hazardous ground conditions differ considerably. This U.S. Bureau of Mines report summarizes recent investigations on the use of stereoscopic (3-D) slides as a training aid for improving the ability of miners to recognize the various geologic and mining-induced irregularities that cause ground-falls. The feasibility of using 3-D slides for training and their effectiveness for representing roof and rib hazard conditions are discussed. Information is presented on equipment and procedures for creating a 3-D slide program that can be updated by mine trainers. Recommendations are made on selection of 3-D equipment and on the use of 3-D slides for training miners to recognize roof and rib hazards.

Jan 1, 1988

By Miguel Gutiérrez

This paper will seek to provide an awareness of the challenges the permitting process presents to the engineering design for open pit mining projects in Perú. This awareness will create a better understanding of the permitting process within the several groups in mining companies that are responsible for getting the mine project started or continue its operations.

Sep 21, 2013

By Clay Haynes

In 2005, Black & Veatch Corporation began designing a raw water conveyance system for San Luis Obispo County from Lake Nacimiento to the city of San Luis Obispo. The first element of the water transfer system will be a raw water pump station and lake tap. The wet well of the pump station will consist of a concrete lined shaft approximately 180 feet deep constructed in the very incompetent sandstone of the Vacqueros Formation. The lake will be wet tapped at approximately 172 feet below grade using a slurry earth pressure balance tunnel boring machine. The 48 to 72-inch finished diameter microtunnel will be approximately 500 feet in length. Construction is scheduled to begin in the winter of 2007.

Jan 1, 2008

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By Donald H. Koch

The project investigated the impacts of coal and mineral storage piles on both ground and surface water quality. The study consisted of two major tacks, Task 1 had two phases. The first phase was field investigations in which ten cons and mineral stockpile sites (5 coal, 5 mineral: phosphate, lead, copper, iron, uranium) across the country were visited to determine the actual impart of coal and mineral stockpiles on writer quality. The second phase of Task I was a series of leaching experiments in which drainage from the ten coals and minerals was controlled and monitored to survey the extent to which storage piles release toxic ions to ground and surface waters. Task IT was n review of pollution abatement techniques with three generic treatment examples applied to lead-zinc ore, eastern coal, and uranium ore stockpile leachate. Major conclusions drawn from the completion of Tasks I and II include: water quality impacts are site specific, there is n high correlation between sulfide content of u material and its solution potential, and the selection of the best treatment alternative for n specific coal or mineral storage area must be based on site-specific criteria, pilot studies on representative leachate samples, and sound engineering design.

Jan 1, 1982

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018