Search Documents

By C. M. Rule

Stirred milling using either horizontal or vertical mills has made a rapid entrance into PGM ore and tailings concentrator flow sheets. Currently there are in excess of 40 units installed in either mainstream, ?MIG? or intermediate concentrate regrind, ?UFG?, applications in PGM, primary ore treatment plants or in tailings scavenging and reclamation treatment plants. This represents a total of approximately 70 MW of installed fine grinding equipment. This paper outlines the reasons why the technology take-up has been rapid and illustrates the advantages of this technology over conventional milling. Keywords PGM, platinum group metals, UG2, Merensky, platreef, stirred milling, MIG?mainstream inert grinding, UFG?ultra fine grindingof intermediate flotation concentrates, IsaMill?, Metso SMD?, Deswik, ceremic grinding media, QEMSEM, MLA.

Jan 1, 2011

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By Pengfu Tan

One copper Isasmelt furnace has been operated in Xstrata Copper at Mount Isa in Australia since 1992. A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper continuous smelting process. The thermodynamic model has been used to model the key parameters in the control of the copper Isasmelt furnace. The effects of the process parameters on the control of the copper Isasmelt furnace have been predicted and discussed. These process parameters include SiO2/Fe, matte grade, coal, temperature, spec air of feed, oxygen enrichment, and MgO contents in slag.

Jan 1, 2006

By Gary L. Seider

Helical screw piles are used in various applications including the underpinning of distressed foundations and as deep foundations for new structures. At present, maximum design loads range between 12.5 and 50 tons. Helical piles installed with in-situ grouting of the central steel shaft are a relatively new type of deep foundation, which have extended the present maximum design loads to the 100-ton range. Vickars & Clemence discussed this new foundation system in a paper presented at GEO-Denver 2000 in Denver, CO. Over the past three years, grouted shaft helicals have been used successfully on remedial and new construction projects all across North America. The authors have studied several construction projects in a variety of soil conditions to compile a list of practical design guidelines. Those guidelines include installability of grouted shaft helicals based on soil type, equipment requirements, grout selection, and theoretical vs. actual load capacity. In a number of cases, full-scale, field load tests were conducted in both granular and cohesive soils and the results broken down between tip resistance on the helix bearing plates and friction resistance on the grouted shaft. Data is presented which will further efforts to develop a design model and method to accurately predict the axial and lateral capacity of grouted shaft helicals.

Jan 1, 2003

By Pupazzoni P. D, Meissner D. C

Incorporating an iron ore pelletising plant, a MIDREX'"' Direct Reduction Plant, and a mini mill, the conversion of iron ore fines to high- quality steel slabs in Western Australia is among the lowest cost routes in the world. The cost and availability of iron ore and natural gas, government support, and proximity to the growing Southeast Asian market all contribute to the competitive position of the area. Owing to the lead-time required, this is an ideal time to develop a new project to supply semi-finished steel to Asia for rolling to a finished product. A project contracted now will start up in about three years, when the market should have recovered.

Jan 1, 1999

By D. B. Felsher

"Lakeshore Gold’s Bell Creek Mill is located in Timmins, Ontario. The mill has been in operation since 2009 and has undergone several small expansions since then. In 2012 - 2013 the first major mill expansion was commissioned raising the mill capacity from 2,000tpd to 3,150tpd. This was done through the installation of a new ROM ore truck dumping facility, jaw crusher, ore storage dome, SAG mill, leach tank, CIL tank, and electrowinning cell. This paper will cover the equipment installed to raise the tonnage as well as the commissioning of the new equipment including problems encountered and how these problems were solved.IntroductionLake Shore Gold acquired the Bell Creek Mill, along with the Bell Creek Mine, from the Porcupine Gold Mines Joint Venture, a joint venture between Goldcorp Canada Ltd. and Kinross Gold Corporation, in December 2007.The Bell Creek mill, which processed ore from the Bell Creek Mine has consistently achieved recoveries of over 95%, is a conventional gold mill circuit, involving crushing and two stage ball mill grinding, gravity and leaching, followed by Carbon-In-Pulp (CIP) process for gold recovery. The facility had been placed on care and maintenance in 2002. At the beginning of 2009, the mill had been refurbished with an initial capacity of 800 tonnes per day and was subsequently refurbished to a capacity of 1,500 tonnes per day near the end of the third quarter of that year. The Mill was then expanded in 2010 to a capacity of 2,000 tonnes per day.In late 2011, the Company commenced a 50% expansion of its milling facility, from a processing capacity of 2,000 tonnes per day to 3,150 tonnes per day. Phase 1 of the expansion, which mainly involved enhancements to the solution circuit (“back end”) and increased the mill’s capacity to 2,500 tonnes per day, was completed at the end of 2012. Commissioning of Phase 2 of the expansion, to a capacity of 3,150 tonnes per day, commenced at the end of July 2013."

Jan 1, 2015

By P Papanastasiou, J Hadjigeorgiou, E Kyriakou

The south west area of Cyprus has a long history of slope instability problems. The location and extent of these landslides has been influenced by ground morphology, geological structure and the presence of weak rocks and cohesive soils. The main triggering mechanisms have been precipitation and/or seismic events. Landslides have contributed to the decision to relocate villages and considerable efforts have been put into maintaining the integrity of the local transportation network. This paper uses a recent case study of road embankment failure near Pentalia in southwest Cyprus to review the available tools for the analysis of slope instability. It further demonstrates how the shear strength reduction technique can be used in a finite element analysis to better visualise the slope instability mechanism of a road embankment and provide a reliable tool in selecting appropriate remedial measures.

Jan 1, 2006

By Mark Fernald, Christian O’Keefe, John Viega

"In this presentation, the SONARtrac™ technology platform will be described. CiDRA's proprietary clamp-on, passive sonar array-based flow meter technology performs two independent measurements – flow rate and fluid characterization. Firstly, the meter provides the volumetric flow rate of the mixture by measuring the speed at which naturally occurring turbulent structures convect with the flow past an axial array of sensors. Secondly, the meter uses similar sonar-based processing techniques and naturally occurring sound in the process fluid to measure entrained air levels. The result is a unique ability to measure the flow rate and entrained air level of most fluids – clean liquids, high solids content slurries, and liquids and slurries with entrained air.Also to be presented is the application of the sonar-based technology platform in a variety of oil sands processes, hydrotransport, and minerals beneficiation applications. In particular, difficult slurry flow measurement and control in the areas of comminution and flotation such as mill discharge, hydrocyclone feed/overflow, final concentrate, thickener discharge, and tailings will be discussed. In addition new real time maintenance free process measurement capability will be presented in the areas of entrained air in slurry, collection zone gas holdup (?g), and slurry velocity profiling. The operational advantages and value of these measurements, even in the presence of scale buildup, will be discussed.INTRODUCTIONFlow measurements in the mineral processing and oil sands industry suffer from the limitations placed by previously available flowmeters including the commonly used instruments such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. The desire or requirement to make a non-contact measurement that is accurate and robust, and can be performed on practically any type of fluid within practically any type of pipe has driven the creation of a new class of flowmeters. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition."

Jan 1, 2007

By John D. Foulkes

A study to categorize and characterize underground metal/non-metal mining operations from the viewpoint of telecommunication requirements and practices. The objectives were to: ? Gather and analyze data; ? Identify communication requirements; and ? Recommend systems for operational emergency and post-disaster telecommunications.

Jan 1, 1979

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By E Heath, F McDermott, S Turner, P van Calsteren

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath midocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and om, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100 000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50 000 years prior to eruption.

Jan 1, 1995

The development of a noise attenuated compressed air driven fan is described. The fan, which employs the jet reaction principle, possesses blade extension pieces which penetrate into an acoustically treated annular chamber. The dominant noise source, namely the air jets, is thereby partially suppressed. In addition, the increased moment arm of the jets leads to an improved propulsion effect which contributes to the improved aerodynamic performance of the unit.A typical measure of the improvement of this type of auxiliary mine ventilation unit is a 4 per cent increase in efficiency and a 10 dB (A) drop in sound level for a fan duty of 0·5 kPa and 1600 litre/s. This degree ofattenuation corresponds to at least halving the loudness level, a subjective noise measure.

Jan 1, 1973

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By J. L. Robson, C. M. Bristow

mass flow rates of particles and air (the loading ratio).

Dec 1, 1994

By D. T. G. Emmett

[ ] South Africa, by a wide margin, is blessed with the largest known world reserves of platinum. The optimal use of these resources for the benefit of all South Africa?s peoples is a goal shared by industry, government and all South Africans. The challenge is to grow the industry in accordance with demand growth and thus to manage a long-term stable growth pattern for PGM usage world-wide. Amplats and the South African producers are well able to meet this challenge [ ] South Africa plays a critical role in the provision of Platinum Group Metals for world markets. In fact no other country has the productive capacity nor the geological reserves to supply the world?s platinum needs. The world required some 5 million ounces of Platinum in 1997 and South Africa supplied a full 74% thereof. The second major supplier, Russia provided a further 18% of world demand, primarily as a by-product of nickel production. Amplats satisfied about 37% of total world demand followed by Impala 20% and Lonhro at 12%.

Jan 1, 1998

By K. Awuah-Offei

An aggregate plant may have difficulty balancing product stockpile inventories if hot mix asphalt (HMA) design engineers do not account for aggregate inventory during mix design. Yet HMA design engineers do not, often, take this into consideration during asphalt mix design. This is due to the lack of tools that enable the lab technician or engineer to optimize the mix for good performance while helping the aggregate plant manage its stockpile inventory levels and reducing the aggregate cost. This work presents a linear programming model of the asphalt mix design problem that helps aggregate plants manage their inventory levels while meeting HMA customer demands. The algorithm is implemented in MATLAB as an Asphalt Mix Design Optimization (AMIDO) program. The program is successfully validated with real-life data. The results show that AMIDO can be used to successfully produce any mix design while reducing the cost of aggregates by using the cheapest stockpile materials. The application of AMIDO will increase aggregate plant profitability when serving HMA customers and could potentially be modified for concrete aggregate customers too.

Jan 1, 2009

By Mario Paredes Malca

El presente trabajo describe el sistema experto por circuito de molienda desarrollado en la Concentradora Toquepala, donde se aplica la tecnología del control experto-basada en conjuntos difusos y modelos matemáticos. Las ventajas que presenta la aplicación de los sistemas expertos comprenden el aumento de la capacidad de tratamiento, la disminución del costo de operación y del porcentaje del producto que no cumple las especificaciones. Asímismo, el sistema experto se integra al sistema de control para asistir al operador en la detección de los casos, donde las operaciones se puedan descontrolar, aunque ésta no sea realmente su principal función. Si se le configura y sintoniza correctamente, el sistema experto detecta, diagnostica en forma continua los problemas de operación y aplica modelos matemáticos y estadísticos de optimización, interactúando con un sistema de control DCS o PLC.

Sep 12, 2005

By Taegong Ryu

Nanosized tungsten powder was synthesized by the hydrogen reduction of ammonium paratungstate (APT) in thermal plasma. The effects of operating conditions on the product composition and particle size were investigated. The particle size of synthesized W powder was less than 30 nm in all cases tested. The sintering behavior of the synthesized powder (25 nm average size) was then investigated and compared with those of commercial W powder of 500 nm average size and W powder of 23 nm average size produced by milling the commercial powder. The sintering was done at 1400oC with various holding times. The hardness of the resulting compact from the synthesized W powder (315 VHN) was similar to that from the milled W powder (309 VHN), but the plasma-synthesized powder had a much lower tendency to form cracks. The compacts of both nanopowders were significantly harder than that of the commercial powder (192 VHN).

Jan 1, 2009

By Paulo de Tarso Rossi Haddad, Eric Valmir Spósito, Cristiane Sales Gonçalves

The heat treatment is a process that acts as a key factor in the tool life of tools made with hot work tool steels. Due to their applications, the main desirable metallurgical properties of this material class are toughness and hot resistance, without which the tools may suffer premature failure, and may lead to increases in the cost of producing articles made using such tools [1, 2]. Therefore, special attention must be given to the heat treatments practiced in these steels, whose operations involve quenching and tempering. The present work carried out the effects of the austenitizing and tempering temperatures on the microstructural condition, hardness and impact properties of TENAX300IM®, modified AISI H11 with lower silicon content. Hardness was measured by the Rockwell method, C scale; the toughness was evaluated by the Charpy-V impact test; and the microstructure for each condition was evaluated by optic microscopy. It was shown that higher austenitization temperatures resulted in increased grain size and hardness; higher tempering temperatures resulted in reduction of hardness, and secondary hardening peaks were observed for some austenitization conditions. The impact resistance showed an inverse behavior to that of the hardness, remaining initially constant, up to ~ 550 ° C of tempering temperature, and then increasing with the tempering temperature. The microstructures presented great dissimilarity, mainly due to the dissolution of carbon and alloying elements in the matrix.

Nov 22, 2018