Search Documents

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine's capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces' upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

Theories of ore genesis. have both practical and philosophical application-practical in that they influence our search for new ore bodies; philosophical in that they provide a test for our theories of petrogenesis-and our ingenuity.For example, the theory of granitization requires an explanation of ore genesis compatible with the general concepts of granitization.Our understanding of some processes of ore formation, such as supergene enrichment, or the formation of residual lateritic iron ores, is so complete as to permit of nq controversy.For other ores, like the oolitic iron ores of England and France, and elsewhere, or the segregations of chromite or ilmenite in basic igneous rocks, the broad principles are generally agreed on; dispute is limited to details of process.But for a wide range of ore deposits there is no such agreement. Completely incompatible hypotheses are advanced to explain' identical facts, and we have difficulty in finding new facts or criteria that will distinguish unambiguously between them.In thinking about such ores, a co:n;venient starting point is provided by Schneiderhohn's (1953) fourfold division of ore deposits:1. The secondary hydrothermal ore deposits occurring in Mesozoic-Neozoic cover strata of Europe.2. The "regenerated" younger ore deposits in Alpine type mountain chains.3. Post-Cambrian primary hydrothermal ore deposits.4. Ore deposits of the PreCambrian shields.To these we may add a fifth group:5. Stratigraphically controlled sulphide deposits.

Jan 1, 1956

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By Leopoldo Mariscal

El presente trabajo describe los aspectos más importantes del proyecto de Fundición de Ilo como son: la tecnología, el desarrollo de la ingeniería y construcción, el impacto económico, social, tecnológico y ambiental de su ejecución y los planes de entrenamiento y comisionado de la nueva planta. Asimismo considera entre los equipos principales: un horno de fusión en baño ISASMELT asociado a un caldero de recuperación de calor y un precipitador electroestático, cuatro convertidores Peirce Smith, dos electroprecipitadores, dos plantas de ácido, dos plantas de oxigeno, dos plantas de efluentes, una planta de moldeo de ánodos, dos hornos de limpieza de escoria, y varias plantas auxiliares más.

Sep 12, 2005

The early history of the mine is traced from the beginning of shaft sinking in 1886 to the purchase by the Broken Hill Proprietary Co. Ltd. in 1949. A necessary preliminary to mechanisation of the Borehole Seam was development of the Young Wallsend seam, andthis development is described. Surface reorganisation and coal handling arrangements are dealt with in detail. Then follows a description of the Borehole Seam mechanisation, the provision of power supply for this purpose, arid pumping arrangements in themine.INTRODUCTIONStockton Borehole Colliery is in the Parish of Teralba, between the townships of Teralba and Boolaroo, and about 12 miles from Newcastle. The colliery holding, a freehofd area of 2,560 acres, was apparently an original land grant when acquired by Teralba Co-operative Coal Company who decided to mine for coal and named the mine "Teralba Colliery." Shaft sinking was commenced in 1886 but was delayed by financial and water troubles to such an extent that it was not until 1901 that the Borehole Seam was reached.Coal was won until 1904 using a single 16 ft. diameter shaft, ventilation being achieved by means of a wooden boxing down one side of the shaft. This collapsed, and operations ceased until the mine was taken over in 1906 by a company known as "Borehole Colliery Limited," the principal stockholder being the Stockton Coal Company. It renamed the mine "Borehole Colliery." This new company immediately commenced sinking a 13 ft. diameter air shaft. In 1908 the Stocktol1 Colliery at Stockton was abandoned, and during the following year much of its equipment was transferred to Borehole Colliery. The name was again changed becoming "Stockton Borehole Colliery." From this period on, coal was produced from the Borehole Seam by...

Jan 1, 1957

By M. S. Miller

With prevailing assumptions that plentiful domestic coal reserves will be available for meeting our Nation’s expectations for on future low emission, coal-fired power plants, major government funding in Clean Coal Technology, and Carbon Sequestration Programs continues to be aggressive. However, after more than a decade of cutbacks in funding for domestic coal-related programs and personnel, there is a growing concern that adequate quantification and qualification of our Nation’s coal reserves is increasingly being compromised. This paper will define the growing concerns and dichotomies that continue to increase, and address the decreasing number of fossil fuel mapping and assessment programs by Federal and State programs.

Jan 1, 2004

The ore milled from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangal1o-calcite and apatite. The silver content of the ore occurs in three minerals-tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations. Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14-18% lead; 3·0-4·5 oz. silver per ton, and 9·5-12·0% zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from 6-8% lead, 1·5 oz. silver per ton, 18-25% zinc with a siliceous gangue. The common Lead Lode gangue minerals-ealcite, rhodonite, bustamite-are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce: 1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc conc,entrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufficient granular material to be utilized as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5,000 tons of crude ore per week. This plant, which operated until January, 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of Hgging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each...

Jan 1, 1941

This paper considers the application of recent laboratory gas sorption data to the understanding outburst phenomena in underground coal mining. Previous use of threshold limits based on gas content and coal rank are placed in perspective. Although this work focuses on overseas research and experience, parallels can be drawn for New Zealand coal settings, taking into account localised mining and geological factors.

Jan 1, 1994

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By Tomás Gonzáles

El presente trabajo describe la metodología usada para evaluar las estrategias de las alternativas del planeamiento a largo plazo en la explotación del mineral y el lixiviable en la Mina Toquepala.

Aug 25, 2002

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By L. F. Albert

The paper describes solutions given to foundation problems during the reconstruction of a power plant set on fire, located adjacent to several still Working Units. After a detailed site and laboratory investigation, it was decided that it could be possible to include within the new foundations the preexisting cast in situ driven piles with enlarged base 50 cm in diameter and let them work with new 41 cm driven, cast in situ piles without enlarged base. Demolition of existing caps was carried out with expansive mortar in order to avoid any possible damage to piles, whose actual conditions were checked by several load tests. New piles were designed to support service load by shaft resistance, in order to limit total and differential settlement. When piles had to be driven adjacent to nearby structures, measurements of peak soil particles velocity were carried out while driving piles at decreasing distance from critical locations. By preboring most of the upper clay layer it was possible to reduce within safe limits for structures the induced vibrations.

Jan 1, 1989

By B. Kahraman

About 70% of the world?s total boron reserves are located in Turkey. Boron minerals are typically concentrated by attrition scrubbing followed by screening and classification to remove clay minerals and other impurities. These wet concentration methods, however, result in a considerable amount of accumulated tailings in large tailings dams. The tailings are approximately 28% solids and contain 14% B2O3. Problems caused by these tailings can be minimized by employing dry beneficiation techniques involving heat treatment. This method has been successfully tested on laboratory and pilot scales. During heat treatment, borax undergoes expansion in volume. The amount of expansion is dependent on the particle size, temperature and duration of heat treatment. Because the optimum temperature and the duration of the heat treatment are not well defined, the boron ore acts as a calcined clay mineral and is discarded along with the gangue. It is important to predict such parameters using mathematical formulations. Thus, a mathematical model is used to predict the required temperature and duration period prior to heat treatment. In the experimental study presented here, a series of systematic thermal tests was carried out in a muffle furnace. Two variables, temperature and time, were studied in a response surface design. A quadratic regression model was chosen and regression coefficients were calculated. Using a regression equation, the volume expansion of the particles in various circumstances can be predicted. The mathematical test results are then correlated with the experimental results to relate the optimum expansion of borax with heating time and temperature and with borax grades and recoveries.

Jan 1, 2008

By Russell J. Foster

Public awareness of, and involvement in, recycling has increased significantly in recent years. Nevertheless, recycling is generally perceived as a new development, and is familiar only in the context of municipal solid waste management. The actual magnitude and scope of metals recycling in the United States have gone virtually unnoticed. Over time, both the quantitative and qualitative aspects of secondary metals recovery and reuse have changed substantially, while the attendant regulations have become increasingly stringent. This U.S. Bureau of Mines report examines trends and developments in major metal demand and recycling, and analyzes the possible impacts of regulations with regard to recycling activities.

Jan 1, 1994

By Liu Wei

In order to make clear the dissolving characteristic of the chrysocolla (CuSiO3?H2O) in the ammonia-ammonium chloride solution, a thermodynamic model of the chrysocolla (CuSiO3?H2O)-ammonia- ammonium chloride-water system is established using the exponential computation method based on both mass balance and charge balance equations. The equation group of the thermodynamic model is solved by the MATLAB Soft on PC. The condition which is favorable for dissolving high concentration of copper in solution is making out. The stable area of chrysocolla (CuSiO3?H2O) and the condition of chrysocolla (CuSiO3?H2O) converting to atacamite (Cu(OH)1.5Cl0.5) is also studied. A group of experiments are designed to validate the veracity of the results of the thermodynamic calculation.

Jan 1, 2010

By A R. Bye, T R. Stacey

Anglo PlatinumÆs Potgietersrust Platinums (PPRust) operates three open pits and plans to excavate 90 Mt of rock in 2007. With pit slopes expected to reach a height of 400 m, the geotechnical department has a key role to play. Over the last four years PPRust has successfully implemented new geotechnical strategies and tactics to reduce risk, improve safety and maximise profitability. A large database of core logging, face mapping and rock testing data has been assembled and used for failure analysis, geotechnical zoning and rock mass ratings. The data has also been used for optimising blast designs on a daily basis through the use of a geotechnical block model. This greatly improves blast fragmentation and therefore loading and milling efficiencies. The slope design process involves limit equilibrium analysis, numerical modelling, rock fall analysis and block modelling. Slope management includes comprehensive limit blasting and visual inspections, and state-of-the-art slope monitoring equipment, namely the GroundProbe radar, Riegl lasers and GeoMoS automated prism monitoring. The risk-consequence approach has been used in slope optimisation, where all the slope analyses, operational controls, costs of failure, economic analyses of various slope designs and fault tree analyses are used to determine the ideal slope designs. These activities added over $25 million of value to the operation and also ensured compliance with Anglo AmericanÆs acceptable risk level. The successful mining of the optimised slopes is to due to the greatly improved geotechnical knowledge and slope management. PPRustÆs geotechnical work is used as a benchmark for Anglo American open pit operations. The focus of the paper will be on the value added to the operation by all aspects associated with slope management.

Jan 1, 2007

By A. R. T. Denues

"INTRODUCTION The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining.In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives. Cushioned blasting is designed to save the energy usually lost in excessive shattering and in this way to effect economies and to produce increased proportions of desirable lump coal. That this saving should lead to greater efficiency is indicated by an analogy with the theory and experience of size-redaction by crushing or grinding from which it is known that a large proportion of the energy consumed is expended in producing the smaller sizes (26),3/. Aside from these considerations, increasing the yield of lump coal is important in practice because larger sizes of coal usually sell at higher prices. Some statistics published in England in 1934 (63) illustrate the economic origin of the interest in increasing yields of lump coal; these indicate for three sizes of coal that as the size decreases the value decreases in the approximate series 3:1.5:1, thus:"

May 1, 1940

By M. N. Bassim, W. W. Tennese

"Concepts of linear elastic fracture mechanics were applied to study two cases of failure, namely an equalizing beam from a tandem rear axle of a highway tractor unit and the main beam of a flat bed trailer. In the first case, the presence of a crack, initiated by stress corrosion cracking followed by significant fatigue crack propagation produced a state of stress which was sufficient to produce brittle failure. Calculation of the fatigue life agreed with the number of cycles that the structure experienced before final fracture. In the second case, it was demonstrated that a combination of low temperature and high loading rate was sufficient to cause brittle fracture.IntroductionFailure analysis of engineering components has generally been carried out without the benefit of fracture mechanics. It is generally understood that real structures inevitably contain internal or surface flaws which under an applied load, may propagate to fracture. Fracture mechanics relates the applied stresses to the crack size in specified geometries. Since its introduction approximately thirty years ago, fracture mechanics has evolved as a design philosophy which can be used to develop fracture-safe designs. It can be also applied in analysis of failures, to ascertain if sound design and fabrication methods have been used."

Jan 1, 1985

THE present article makes no claim to be exhaustive, since it cannot contain all the knowledge which scientists and manufacturers of the compounds of the rare earths have gained. The following notes are, therefore, simply an attempt to ascertain andclearly record the occurrence, properties, and uses of the more important of the rare earths, with a special reference to their commercial values and the industries based upon them.HISTORYIt was the mine manager, Gcyer, of Stockholm, who, in 1788, first drew attention to a black mineral which had been found in a quarry near Roslagen, in Sweden. In 1805 Klapproth received some specimens of this mineral, which he declared to be a newmineral. Subsequently Gadolin, professor of chemistry at Abo, analyzed the same mineral, and determined the presence of an unknown earth resembling alumina and lime. He named the mineral ytterbite, and afterwards gadolinite. Klapproth has alsothe merit of having detected (1804) another rare earth, which he named ochroit-earth, found in the Bastnas mine, near Riddarhyttan, in Wcstmannland, Sweden. Curiously enough, Hisinger and Berzelius simultaneously ascertained the existence of the same...

Jan 1, 1909