Search Documents

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By Fan Shaogang

In this paper, the airbags' structure and technical characteristics and its applications in China are described. Based on the practice of the airbags in mining thin seams, the effects on ground control are discussed. This paper also analyzes the interaction mechanism between the airbag and surrounding rocks.

Jan 1, 1997

By Andrea Koschinsky, Sophie Paul

"INTRODUCTIONOnce again deep-sea mining has been receiving a lot of attention in recent years. Industrial and political advancements also call for environmental baseline studies and analyses to aid the development of standards and monitoring protocols. As part of the EU research project “JPI Oceans: Ecological Aspects of Deep-Sea Mining”, the RV Sonne cruise SO242 to the Peru Basin revisited the DISCOL area that had been artificially disturbed in 1989. This offered the unique opportunity to study a deep-sea site 26 years after a disturbance similar to manganese nodule mining had been carried out (Figure 1). A comparison of a variety of undisturbed and disturbed sites shed light on the re-establishment of a geochemical equilibrium and a range of baseline values. This information can help to inform standard development for monitoring and mining purposes.Heavy metal data and its applicationResearch findingsDuring the cruise, disturbed and undisturbed surface sediment was sampled. The pore water analyses show that the 26 years old disturbance is not visible in the metal profiles and that the pore water reaches equilibrium through diffusive fluxes relatively quickly. The sediment, however, shows some differences between disturbed and undisturbed sites in the upper 20 cm, even after 26 years. Lower concentrations in the usually manganese-oxide rich top layer, variations and “unnatural” peaks in the manganese profiles, for example, suggest removal or mixing of the top layer (Figure 2)."

Jan 1, 2017

Assuming that a gold ore has been effectively ground to ensure maximum economic liberation of gold, the circuits that will have the most effect on the successful operation of a gold plant will be that of the leaching and carbon-in-pulp circuit (CIP). The reagent and utilities operating costs associated with leaching, adsorption, elution and regeneration would typically make up some 15% of total operating cost, whilst the capital costs associated with these areas is about 16% of the total. Although not largest (capital and operating costs associated with comminution are generally dominant) these items represent a significant proportion of capital and operating cost. Much more importantly, these plant areas represent the primary gold recovery process and their technical and operational efficiencies will have a significant impact on overall plant efficiency. The objective during process design of these sections is thus to develop a design which provides maximum technical and economic efficiency and which is robust to potential changes in ore throughput, mineralogical characteristics and head-grade. Experience has shown that, particularly for longer life and higher-grade projects typical of the South African underground gold mining industry, small changes in recovery and efficiency have a significant value over the life of the project.

Jan 1, 1999

By R. A. Franks

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system?s ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system?s ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health.

Jan 1, 2008

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

By Mao Bai

In predicting the integrity of under-mined structures, surface horizontal displacements and curvatures are frequently of greater importance than the more homogeneous vertical displacements. Accurate evaluation of mining induced subsidence and horizontal displacement further requires that the predictive model adequately represents the subsurface geology, mining geometry and extraction sequencing. The following documents an extension of the Subsidence Prediction and System Identification method (SPASID) to the evaluation of horizontal strains. Comparisons are made between predictions from SPASID and two other empirical methods against measured data from a case study. The system identification method is illustrated to predict horizontal displacements and strains most consistently with the in situ data.

Jan 1, 1989

By Olav K1omstad1ien

The lean, but extensive iron ore deposits of the Dunderland Valley north of Mo i Rana, Norway, is the raw material for the Rana Mines which is a division of the state owned steel mill A/S Norsk Jernverk. Activities for the exploitation of the orebodies were commenced in 1902 by the English Dunderland Iron Ore Company. During its operating period the company constructed a total of two large scale concentrating plants. The activities were strongly marked by technical problems and labor disputes. Thus actual production was limited to the years 1904-1908, 1928-1931 and 1937-1939. During these periods a total of 1.9 million tons of crude ore was mined and 0.6 million tons of concentrates produced for export. The present plant commenced operations in late fall of 1964. Up to and including 1976 about 26.6 million tons of crude have been put through the concentrating plant and about 10.7 million tons of concentrate produced.

Jan 1, 1978

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By Galyn Rippentropp, Finn Erik Overlie

INTRODUCTION The wet shotcreting system utilizing steelfiber microsilica shotcrete with remote controlled equipment (The Robocon System) was developed in Norway 7-8 years ago. Norway was the natural origin for this system due to several factors. Almost 30% of all underground hydro-power stations in the world are located here. These projects created a need for high productivity shotcreting rigs for the rock support work in the caverns and in the connecting tunnels. During the period of 1976-1980, more than 1000 miles of tunnels were completed in Norway. Secondly, the utilization of microsilica in concrete was also developed in Norway due to a concentration of the world's ferroalloy p ants there. Robocon has presently placed approximately 110,000 m (150,000 cu. yds.) of this superior shotcrete, and has consequently an extensive experience in the shotcreting method. During a relatively short period of time (1975-1980), Robocon had a change from hand-operated, dry-process shotcrete to remote-controlled, wet-process shotcreting, because of improved productivity, reduced rebound, safer and cleaner working conditions. The introduction of microsilica and water-reducing admixture made it possible to produce wet-process shotcrete of high strength.

Jan 1, 1987

With the change in legislation under the Resource Management Act 1991 (RMA), the responsibility for administering the effects of blasting on the environment, has transferred from an essentially central government system to local bodies. This naturally will allow for a variety of compliance levels and control procedures which will depend on the particular local body and rather ad hoc arrangements. It is anticipated that the existing NZ Standard on blast vibration levels will soon be replaced by the Australian Standard. These changes raise the question as to what should be used as suitable compliance levels to prevent damage to structures. The paper will address the measurement, control levels and the appropriateness of current standards in relation to the overall legal framework of the RMA.

Jan 1, 1996

By Jana Dobrovska

The paper deals with new approach for measurement and evaluation of chemical microheterogeneity of elements in polycomponent metallic systems (i. e. steels, Ni-alloys). The method is based on the original mathematical model for determination of distribution curves of dendritic segregation of selected elements and on the original mathematical model for determination of the effective partition coefficients of these elements in the structure of analyzed alloy. Application of the method at research of chemical heterogeneity of continuously cast steel slab is also presented. The original results of measurement of dendritic microheterogeneity of eight elements (Al, Si, P, S, Ti, Cr, Mn and Fe) in structure of nine zones of a transversal section of slab are given.

Jan 1, 2006

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By A. B. Parsons

Jan 1, 1971

The Pike River Coal Company is set to develop the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. As such, the major restriction to planned extraction is protection of:   +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2005

The objectives of this paper are two-fold. First, it will show what problems can arise when single estimated values are substituted for a distribution of values when evaluating an open pit mine project in the face of uncertainty. Secondly, it will show how the ability to deal with uncertainty and risk in mine project evaluation can have a significant impact on the ownersÆ and stakeholdersÆ investment decision-making. Here a new mine evaluation framework, the integrated valuation/ optimisation framework (named IVOF), is introduced as an alternative tool for mine project evaluation where uncertainty and risk are incorporated in the evaluation process.

Jan 1, 2009

The sulphide ores of the principal lodes of the Boulder Mines are mainly composed of a schistose guess with a varying proportion of silica and lime, containing tellurides of gold, silver and mercury, associated with iron pyrites. It is a great difficultyto obtain pure and homogeneous samples of the tellurides for analysis, and from a number of tests made with excellent specimens it was found hardly possible to procure two to agree in analysis, the precious metals being found to be combinedwith tellurium in most varying proportions indeed, a close inspection of a partially crushed specimen will reveal, even to the naked eye, the various shades of colour characteristic...

Jan 1, 1901

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011