Search Documents

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

In the course of the last twenty eight years the copper lodes of New Caledonia have been periodically worked or abandoned, until quite recently, probably attracted by the higher price of the metal, British capital has again been induced to embark upon the further development of several copper properties, which at present give reasonable promise of becoming regular producers. Owing to its proximity to Australia (only a three day's journey by mail steamer from Sydney) New Caledonia becomes of additional interest to Australian commerce in general, and it is to be hoped that the French Government may see their way before long to make the best of this natural position, to the mutual benefit of both countries concerned.Op till now all copper ores and concentrates which have been shipped from New Caledonia, were treated in Australian smelting works furthermore, Australian mine managers and miners have from time to time been connected with New Caledonian mining ventures, but, unfortunately, it must be said that nearly everyone of them returned to Australia thoroughly disgusted with his experience over there. Even to the casual observer, it is not so very difficult to find a proper explanation for these shortcomings in the peculiar economic conditions of the 'French colony, as many of the objections which have hitherto existed in connection with mining operations, were the direct consequences of a system of colonisation which could not possibly have been productive of better results.

Jan 1, 1901

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

Education and training research is a major component of the Bureau of Mines human factors research program. The goal of human factors research is to enhance human performance for the purpose of improving both safety and the profitability of the minerals industries. This is achieved through the design of mining equipment, work tasks, management procedures, and development of human resources. This proceedings volume presents several new developments that are helping to improve the quality and efficiency of health, safety, and occupational skills training in the mining community. Several papers address the issue of how to teach and assess miner abilities to deal with underground mine emergencies. Other papers examine practical procedures for defining and cost justifying the integration of structured training and other performance improvement strategies to enhance the proficiency of the work system.

Jan 1, 1988

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

By James Ridenour

This report represents the first comprehensive accounting of lode mining sites in the Loon Creek mining district, Custer County, Idaho. Thirty-five mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were field checked and the updated information added to the data base. The district's major deposits are gold-copper-silver fissure-fillings hosted by biotite schist intruded by dikes ranging in composition from rhyolite to lamprophyre. These deposits contain a trace element suite similar to Tertiary pink granites and may be related to intrusion of the nearby Casto pluton. Continued firm gold prices could stimulate the search for precious metal occurrences in this and other mining districts in central Idaho.

Jan 1, 1983

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

This paper describes a simple finite element (FE) modelling approach which leads to the computation of seismic energy release rate (ERR) and strain energy storage rate (ESR) which result from mining. The concept of critical strain energy is introduced as a means to help evaluate the strainburst potential in mine structures. A new, energy-based, burst potential index (BPI) is proposed. The use of ERR, ESR and BPI is demonstrated by a cut-and-fill stope case study. The merits of using such energy parameters in the interpretation and analysis of strainburst phenomena are discussed. While the study gives promising results, site-specific back analyses would be required to first calibrate the model and fit it with the local mine conditions, before it can be adopted as a routine design tool.

Jan 1, 1999

By W. M. Scheding

"There has recently been a resurgence of interest in unit flotation of mill discharges. At the Kidd Creek concentrator, this technique has been successfully applied to silver flotation in a 3050 mtpd silver-copper-lead-zinc division. The major incentive has been improved silver payment through increased overall recovery and better distribution between the sequential copper, lead and zinc concentrates. A large, but variable fraction of the silver in the ore is present as native silver and, being dense and malleable, is susceptible to overgrinding. Grinding circuit surveys showed high concentrations of silver in both primary and secondary circulating loads. Laboratory testwork confirmed that this was selectively flotable, identified the secondary ball mill discharge as the best feed stream and optimized flotation conditions. A 10 t/h pilot plant campaign confirmed that the rate of accumulation of silver was sufficient to sustain continuous production of a silver concentrate and that flotation of the whole stream was not necessary.The present 30 t/h production circuit recovers from 5 to 50% of the silver in the ore at a concentration ratio between 25 and 250. The circuit also contributes to a better understanding of ore mineralogy, as an 'on-line' indicator of elemental silver content."

Jan 1, 1985

By N A. Sikwa, L M. van Niekerk, G N. Ndlovu

In June 2012, Lucara Diamond Corporation officially commissioned its Karowe Diamond Mine in Letlhakane, Botswana. The processing plant circuit incorporates variable speed autogeneous milling, a first for African diamond processing - only previously practiced in Russia. The paper discusses the basis for the selection of milling against the more traditional circuits incorporating crushing and scrubbing. It covers early commissioning challenges of operating a mill in an æalien environmentÆ with no immediate reference plant to look up to for bench-marking.The paper describes how these challenges were overcome and learnings quickly incorporated into the mill operating philosophy for maximum diamond liberation and minimum product damage. The plant was commissioned in three months and by August 2012 the production ramp up had reached name-plate capacity. The feed to the mill has varied from highly weathered material to extremely hard kimberlite and the operating philosophy had to be optimised for the full range of ore types. While more work is required to stretch the mill operating envelope coupled with other circuit additions to improve liberation of fine diamonds at minimum capital expenditure, the mill has, to date, performed to its billing.CITATION:van Niekerk, L M, Ndlovu, G N and Sikwa, N A, 2013. Commissioning and operating an autogeneous mill at Karowe Diamond Mine, in Proceedings MetPlant 2013 , pp 215-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J Wei, A Yo, R Levy

Waste water reuse from municipal and industrial effluents is becoming increasingly important in many areas around the world. Water scarcity, local regulation and environmental impact are driving many industries like coal and copper mines to reuse the large volume of waste water they produce. For example, the Chinese coal industry generated about 4.2 billion tons of mine waste water in 2005 of which only approximately 30 per cent was reused. Coal energy represents 76.6 per cent of the total energy generated in China in 2007 and most of the coal-fired power plants are located in north-west of China, which is a water stressed area.The selection of mine waste water treatment process is challenging as the effluents typically contains high levels of organic compounds and salinity and their composition can vary significantly. In recent years there has been a growing interest in the integration of ultrafiltration (UF) and reverse osmosis (RO) membrane technologies for mine waste water treatment and reuse.In this paper, an overview of the design and performance of ultrafiltration and RO membranes applied for reuse of mine waste water are discussed. A study was carried out in two effluents treatment plants treating copper and coal mine waste water, which are located in Chile and China respectively. The following topics will be discussed to demonstrate the performance of an integrated membrane system in mine waste water reuse: The main challenges from copper mine waste water treatment: high level of chemical oxygen demand (COD); high level of total suspended solids (TSS); high salinity; high concentration of silica, sulfate, iron and other contaminants; and fluctuation of raw water quality. The main challenges from coal mine waste water treatment: high level of total dissolved solids, and waste water quality fluctuation. Design parameters for waste water treatment systems: Selection of pretreatment for dual-membrane system in the copper mine: Clarifier with coagulation and flocculation to remove high TSS; Dissolved Air Flotation (DAF) to remove non-settling solids; Media filtration to handle fine solids and particulate organics; Activated Carbon filters (ACF) to remove dissolved organics, colour and odours. Selection of UF and RO membranes and specific design of their recovery, flux, chemical dosage and cleaning regimes. Finally, the performance of UF and RO, including the main fouling factors and efficient cleaning procedures, will be presented and compared to the design parameters to demonstrate the efficiency and performance of the selected integrated membrane systems in each case.

Jan 1, 2009

IN a mine with any considerable output the economical handling and transport of ore underground is a matter of prime importance, and in the design or lay-out of a trucking system the question of what form the points and crossings are to take should be one of the first considered. Trucks may be moved from one line of rails to another by the following means: by flat sheets, with which may be coupled turn-tables, or by points and crossings. The latter class may be further divided into fixed and movable points.Flat sheets and turn-tables, owing to the time and skill needed by the trucker in using them, are seldom of great value with large tonnages, unless for purely temporary work, and the choice narrows down to one between fixed and movable points andcrossings. Both systems have their disadvantages - movable points being liable to jamb with dirt and get out of order, whilst with fixed points trucks may sometimes run over the points and capsize, or go on to the wrong line, though this is not of frequent occurrence. On the other hand. the fixed points are simple, easily laid, and strong, and there is no necessity for the trucker to work any levers, the truck being guided on to its new direction by screwing.Cast-iron points and crossings were first introduced into the North mine during the opening-up of the 950-ft. level, and the first arrangement was designed for a double turn-out in the main crosscut. Since then both the points and crossings have beenmodified several times, and it may be interesting to briefly outline the various forms through which they have passed, showing the reasons for the retention of some features and the rejection of others.

Jan 1, 1915

By Wenming Wang

Recycling of retired cadmium telluride (CdTe) photovoltaic (PV) modules has attracted attention due to new European environmental regulations. Recycling tellurium from CdTe PV modules is becoming more important because of the low availability of this metal. We investigated several treatment paths for reclaiming tellurium from solutions obtained from leaching fragments of CdTe PV modules. Our experiments showed that conventional soda ash neutralization/hydrolysis methods recovered only 50~60% of tellurium. However, by appropriately combining neutralization and sulfide precipitation, almost all the tellurium present in the leaching solution was precipitated and recovered; the concentration of tellurium in the processed solution was reduced from 900-1000 mg/L to less than 1 mg/L, yielding a tellurium recovery greater than 99%. This method can be incorporated in the scheme of recycling spent CdTe PV modules and manufacturing wastes. It may be also an alternative to the current operations for removing tellurium from copper anode slime leaching solutions.

Jan 1, 2006

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Temple Mountain mining district is unique among the uranium-producing areas on the plateau. This relatively isolated mining district is in Emery County, Utah, on the eastern flank of the San Rafael Swell, about 35 miles southwest of the town of Green River. The district lies just within the eastern escarpment of the San Rafel Reef - a rampart of rugged and tilted sandstone cliffs that encircles the highly eroded core known as the Sinbad Country. The presence of petroleum matter found associated with the ore deposits, the occurrence of uranium in various formations, and the structural deformation caused by collapsed features have aroused a great deal of geologic interest. Mine development on Calyx Flat is distinctive, in that the ore deposits are worked through 36-inch calyx-drill holes.

Jan 1, 1957

By Brian Stump, David Anderson, D. Craig Pearson, Robert Martin

Mining explosions designed to move, bulk or fracture rock are often composed of a number of explosions arranged in a complex spatial and temporal pattern. The effects of the explosions are strongly dependent upon the design and implementation of this blasting pattern. This paper describes the collection, combination and visual display of multiple types of data from these explosions for the purposes of understanding the relationships between the blast design, implementation, and observations. Data sets consist of three-component ground motion, acoustic, video and high speed film, three-dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions studied include simple single-fired contained explosions, ones designed to bulk and fracture rocks and those that cast material.

Jan 1, 2000

Electronic noses are being used in the processing industries and in fields such as environmental and occupational hygiene to detect a wide variety of problems from contaminated foods to toxic chemicals in soils. Recently, research has been conducted into the use of these devices for detecting spontaneous combustion in mines with the aim of producing a method for early detection of a developing heating. Gas samples were collected from both SimtarsÆ 16 m3 large-scale spontaneous combustion reactor and the University of QueenslandÆs two-metre column. The samples were analysed using an electronic nose. GCMS and HPLC were used to identify some of the components present. A number of issues both from a practical mine situation and a scientific standpoint have been identified that need to be addressed before these devices can be used to detect a developing heating. Aluminised bags routinely used in the mining industry to collect gas samples for analysis of the permanent gases are not suitable for use with electronic nose devices as they have a æfingerprintÆ from the polymer lining that interferes with the coal heating fingerprint. Tedlar bags used for environmental gas sampling are also unsuitable due to their fingerprint. Gas samples can be collected in glass gas bulbs with aluminium seals and successfully analysed. However the aluminium foil used to seal the bulbs is a restricted item in underground mines. It was also found that the volatile organic fingerprint of the coal heating was extremely weak at temperatures below 130¦C. Before a useful application can be developed, further investigation into the chemical species present in the off-gases from Australian coals is required.

Jan 1, 2005

By F. W. Horton

This paper covers the salient features of the occurrence and mining of sheet mica in the United States and the preparation of mica for market; presents the results of a study of the physical properties of domestic and foreign micas, which the author hopes may he of interest to every mica user, as it definitely answers many questions as to the suitability of various minas for particular purposes; and discusses mica-trade conditions and the future outlook for the domestic mica industry. ACKNOWLEDGMENTS The author takes pleasure in acknowledging his indebtedness to J. R. Thoenen, of the United Stator Bureau of Mines, under whose guidance the work reported herein was performed, and to Frank L. Hess, also of the Bureau, for information on the geological and mineralogical characteristics of mica-bearing pegmatites.

Jan 1, 1935

By K. C. Dean

Changes in the types of materials used for the construction of recent automobile models have occasioned a review of the continued applicability of current recycling techniques. Plastics are being used increasingly in late model cars. To evaluate the changes occurring, a 1972 Mercury Montego, furnished by the Ford Motor Co., was completely dismantled and analyzed, and the composition was compared with that of a composite automobile from 15 vehicles ranging in date of manufacture from 1954 to 1965 and designated as a circa 1960 model. The composite vehicle contained about 26 pounds of plastics, while the 1972 model contained over four times that quantity. The increasing use of plastics in automobiles suggests that research to improve the economic potentiality of plastics recycling is warranted.

Jan 1, 1974

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963