Search Documents

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

Lead isotope measurements indicate that lead from the A.B.H. Consols mine and two transgressive veins in Browne's shaft is "Thackaringa" type and not "Broken Hill" type.

Jan 1, 1970

By George C. Branner

This circular is concerned with eight nonferrous scrap metals as they generated, collected, prepared, and consumed in California. Brief reference also is included with respect to Nevada and Hawaii. Four of these scrap metals - copper, lead, aluminum, and zinc - are of major importance and make up about 95 percent of the total value, whereas the remaining four - antimony, magnesium, nickel, and tin - make up the remaining 5 percent. For convenience, the subject matter is divided into three parts, (1) Data with respect to the collection, preparation, and marketing practices that are common activities to all the nonferrous scrap metals; (2) separate discussions and statistical data with respect to each of the eight nonferrous scrap metals in California; and (3) data with respect to Nevada and Hawaii.

Jan 1, 1962

By Larissa Koroznikova, Steve Durkin, Patrick Bouwmeester, Michael Tuck

In currently used mining methods, blasting techniques often causes dilution of valuable ore and results in costly processing requirements. In the context of narrow vein mining of thin and highly concentrated orebodies there is a need of a mining method that can reduce dilution in order to remain economically viable. This research project explored the viability of a new mining technology, thermal fragmentation, in narrow vein mining. Thermal fragmentation technology uses a flame jet to produce extreme heat that spalls the surrounding rock to a strategically located drill hole, as an alternative to traditional blasting. This paper creates a net present value (NPV) model of a mining method using thermal fragmentation, as well as for an existing method used for narrow vein mining; comparisons and evaluations were made regarding the feasibility of the new technology. It was found that while overall costs for thermal fragmentation were relatively high, reductions in wages, haulage and processing costs, as well as increased productivity and ore recovery, meant that the new method would improve the financial performance of any operation. These results identify that there is an opportunity to introduce the thermal fragmentation technology to narrow vein mines within Australia, in order to lower costs and increase profit.

By Halvorsen N

For mining medium-hard materials on the surface, "Continuous Surface Miners" have been employed for some years. The latest generation surface miner extends the performance of this type of machine to the point where the same cost efficiencies can now be achieved in medium-hard materials as has been achieved in softer materials by machines such as the bucket wheel excavator. The paper explains briefly the technology of the Krupp Surface Miner (recently released to the market) and develops the costs of ownership and typical operating costs. Comparisons are made between a shoveLtruck system and Krupp Surface Miner (KSM) systems based on both truck and conveyor transport systems. Further benefits of mining with the KSM, such as environmental, selective mining and improved product reovery are discussed briefly. The equipment is now available to mine semi-hard materials (with compressive strengths up to 60MPa) on a continuous basis and reap the benefits which continuous systems can deliver. All new and existing open cut mines should review their costs with regard to this technology.

Jan 1, 1990

By Zoë Mullard

Just as a mine has a lifecycle, employees working within the mining sector also make several transitions throughout their career, from initial recruitment to retirement from the industry. Throughout the employment lifecycle, employees bring skills and knowledge that significantly contribute to the global economy. These skills are developed through education, professional training, coaching and through hands-on experience. Despite the current economic conditions and the demand for minerals, the mining industry is facing a substantial skills shortage due to the disparity between the number of new workers entering the mining industry and a largely ?graying workforce?. Although educational programs continue to evolve to attract people with a wide range of skills, the diversity of jobs and the strains of working in remote mining operations continue to present challenges for recruitment and retention of employees. This gap also presents challenges around knowledge transfer at a corporate and mine-site level; employers will require cultural and techno-sociological approaches to ease through these transitions. At the same time, there has been an explosion of social media tools that facilitate information sharing, cross-organizational collaboration, distance learning and knowledge capture. These tools have become increasingly popular in the last few years and their applications vary widely. The mining sector has started to adopt these tools for a number of purposes, including opportunities to harness social media to enhance human resources interactions, outreach and oversight. This paper will outline several case studies that explore leading practices for how the application of new media can assist organizations and individuals as they progress through their careers. This paper will illustrate how new social media communication technologies can be used to increase employee engagement and build organizational capacity in the mining industry. The paper will also include strategies for how to implement social media to enhance human resources applications and will cover ideas for monitoring and evaluation.

Aug 1, 2013

The placer mining industry of the West Coast region of the South Island is based largely around the production of alluvial gold, although other valuable minerals are also present. Since the first major discoveries in 1864-65, reported gold production has totalled around 264 t (8.5 Moz). During the past 10 years, annual production has totalled around 1460 kg (47,000 oz). It is anticipated that gold production over the next three years will continue at a level of 1400-1800 kg.   Annual gold production peaked during 1866 at approximately 17,170 kg (550,000 oz) and has not exceeded 100,000 oz since 1885. This reflects the ease with which gold was won from shallow, rich deposits that were present at many localities. Subsequently, there has been a general decline in the availability of this type of deposit, a trend that will continue in the future. This paper outlines the present state of placer mining in the West Coast region, gives some historical background to the industry and briefly predicts future trends.

Jan 1, 1997

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

By Charles H. Rich

This Bureau of Mines report is an expansion and update of Information Circular 8719 and comprises maps and tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The maps show the locations of the planned or proposed facilities. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities. The report covers the 24 States west of the Mississippi River including Alaska and Hawaii. Of the 808 projects for which information is provided, 219 concern coal mines, 246 concern electric generating plants, and 115 concern uranium mines; Energy Supply and Environmental Coordination Act coal conversion notices are also included. Because of the dynamic nature of the energy industry, many uncertainties exist and some of the listed projects may never become realities. Also, no attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1978

By G. Vouille, P. Bérest

Residual stresses observed in rocks often result from non-compatible initial strains. These stresses can be determined when the incompatibility tensor associated with the initial strain tensor is known. The residual stresses in a cylindrical rock sample can be computed the sample is considered small enough for its incompatibility tensor to be constant. Les contraintes résiduelles, dont on observe couramment les manifestations dans les roches, résultent souvent de l’existence de déformations initiales non-compatibles. Ces contraintes peuvent être calculées lorsque le tenseur d’incompatibilité associé aux déformations initiales est connu. Les contraintes résiduelles dans une éprouvette cylindrique sont données dans le cas où le tenseur d’incompatibilité est constant. Eigenspannungen, die man haeufig in Steinen beobachtet, sind oft Ergebnis einer inkompatiblen Deformation des Anfangszustandes. Diese Spannungen koennen berechnet werden, wenn der Inkompatibilitaets-Tensor der Anfangsdeformation bekannt ist. Die Eigenspannungen einer zylindrischen Probe werden fuer Fall eines konstanten Inkompatibilitaets-Tensor bestimmt.

Jan 1, 2003

By K. Sugawara, Y. Hirakawa, A. Sato

The rock mass properties such as deformability and permeability are highly dependent on the existence of cracks. The Ratio of Crack Opening Dependency (RCOD) was proposed as a new index to evaluate the deformability of infinite jointed rock mass. The RCOD is defined as the ratio of total amount of crack opening and the total deformation of jointed rock mass. The theoretical relation between the RCOD and the effective compliance of jointed rock mass is discussed and confirmed through two-dimensional numerical analysis by the SC-DDM, together with the applicability to the rock engineering. Les propriétés de masse rocheuse telles que la déformabilité et la perméabilité sont très dépendantes de l'existence de fissures. Le rapport de dépendance d'ouverture des fissures a été proposé comme un nouvel index d'évaluation de la déformabilité de masse rocheuse à assemblage infini. Le rapport de dépendance d'ouverture des fissures est défini comme étant le pourcentage de quantité totale d'ouverture des fissures et de déformation totale de la masse rocheuse assemblée. Le rapport théorique entre le rapport de dépendance d'ouverture des fissures et la compliance efficace de masse rocheuse assemblée sont traités et confirmés au travers d'une analyse numérique à deux dimensions par SC-DDM en même temps que l'applicabilité à l'ingénierie des roches. Die Felsmasseneigenschaften wie Verformbarkeit und Durchlässigkeit sind hochgradig abhängig von dem Vorhandensein von Rissen. Das Verhältnis der Riss-Öffnungsabhängigkeit (RCOD) wurde als neuer Index der Verformbargkeit von infinit zerklüfteter Felsmasse vorgeschlagen. Der RCOD wird als Verhältnis der Gesamtmenge der Rissöffnungen und der Gesamtverformung der zerklüfteten Felsmasse definiert. Die theoretische Beziehung zwischen RCOD und der effektiven Verformbarkeit von zerklüfteter Felsmasse wird diskutiert und durch zweidimensionale numerische Analyse mit SC-DDM bestätigt, zusammen mit der Anwendbarkeit auf Bergbautechnik.

Jan 1, 2003

By Monger N. R

Factors leading to the decision to use Joy Continuous Miners for pillar extraction in the Burwood Colliery are outlined. A detailed description is given of the Joy 1-CM-2 Continuous Miner, including the power supply to the machine, and the method of cutting coalfrom a face. Modifications found necessary in practice are dealt with.The Joy 10 S.C. shuttle car used in conjunction with the Miner, and alterations made to this unit, are then described, together with Ancillary units for the whole installation such as transformers, motor generator set, air compressor,_ cables for power supply and water supply for dust suppression.Special arrangements were necessary to transport the Miner and Shuttle Cars through the tunnel to the Victoria Tunnel seam, and the method of overcoming the transport difficulties is discussed. Manning of the Continuous Miner unit, and final preparation andsubsequent working of the pillars is outlined. Special attention must be given to maintenance of the machines.It is concluded that the combination of Joy Continuous Miner and Shuttle Car is an excellent method for removing pillars in the Burwood Colliery.INTRODUCTIONThis paper deals with the Burwood Colliery in the RH.P. Group in which some units are engaged in the mechanical extraction of pillars with Joy Continuous Miners.In 1941, an amendment to the Coal Mines Regulation Act of N.S.W. forbade the extraction of pillars by mechanical means unless with the express permission of the Minister for Mines. As this permission was not forthcoming, no mechanical extraction of pillars took place in Australia until 1954 As it was doubtful during most of this period whether mechanical extraction would ever come about, coal generally was won with a view to maximum extraction in the first workings, thus giving rise to centre gannon bord panels and 45° angle cut throughs as shown in Fig. 1.

Jan 1, 1957

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

This paper briefly reviews the demise of professional mining education and training in NZ over the past ten years; compares it with the Australian experience; and discusses the immense success experienced by EXITO and the upsurge of competency based education and training we are currently experiencing in the mineral extraction and associated industries. It also looks to the development of a Bachelor in Mining Technology.

Jan 1, 2001

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007