Search Documents

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Helge Rosenberg

Up to now, Topsøe WSA (Wet gas Sulphuric Acid) plants have been in operation for almost 30 years, and close to 80 plants have been sold. In spite of its unique features and ability to treat gases without any prior drying, the WSA technology has had certain restrictions with regards to SO2 concentration in the feed gas, and the overall conversion of SO2 by catalytic means has been limited to approx. 99.7%. In commercial scale sulphuric acid production on the basis of elemental sulphur and metallurgical off-gases, there is a demand for higher SO2 conversion and treatment of gases with a higher content of SO2. Therefore Topsoe has further developed its WSA technology to cope with these demands. This paper will explain more about the principles of such new development and leave the delegate with a better understanding of the potentials of the new generation of the WSA technology from Topsoe.

Jan 1, 2009

By Sara Jane Boles

The purpose of this Bureau of Mines investigation was primarily to isolate and examine the effect of liquid content upon the apparent porosity and bulk density of compacts pressed from high-purity, fused aluminum oxide, and, secondarily, to study the actual mechanism by which the liquid content affects the bulk density. No attempt was made to approach the theoretical maximum density of the oxide by introducing additives, particle packings, or similar variables; instead this study is an intercomparison of the bulk densities obtained as functions of the water contents of the compacting mixtures. Water content was varied from 7 percent to 25 percent, on a total-weight basis. The data gathered indicated a well-defined optimum water content for obtaining minimum apparent porosity and maximum bulk density, under the conditions of the experiment. During the course of this study, a number of additional variables in the forming process were discovered and are introduced in this report, although a thorough evaluation was found to be beyond the scope of this present investigation.

Jan 1, 1963

Study on Rational Process Flow Sheet for Beneficiating Low-Grade Cu, Mo, Bi, S, W Polymetallic Ore

Sep 13, 2010

By Roland C. Walker

Traditional headed rebar has existed in the mining industry as a ground support product for many years. The head of a rebar bolt is most commonly produced by hot upset die forging. Upset die forging produces a rugged, simple head that performs well. Certain elements of the head must comply with regulatory standards, such as ASTM F432-95, which offers a standard test procedure to ensure quality of the product. The head style produced by all major manufacturers has been optimized to reduce manufacturing costs, provide greater miner safety and provide an excellent performing product. Observations were made in some mines of heads failing under in-situ loading. These observations could not be replicated according to the ASTM testing method. This paper highlights the problem and how a solution was developed. The development includes pictures of in-situ failures from the underground operations, laboratory replication tests indicating how this loading occurs, and then the use of this calibrated test method to validate the new design created.

Jan 1, 2009

By Gabriel Gonçalves Pessoa de Castro

O trabalho teve por objetivo produzir uma liga Al AA1070 com granulometria fina a partir de um material com granulometria grosseira, por meio de deformação plástica severa (DPS) aplicada por prensagem por canais equiangulares (ECAP) via rota C, bem como esclarecer e avaliar os mecanismos responsáveis pela evolução microestrutural durante este processo de prensagem. O processo empregou a rota C com 5 passes consecutivos a frio e acumulou uma deformação ?5 = 5,95. O material de partida é proveniente de um processo de laminação a quente, com uma microestrutura de grãos grosseiros com tamanho de grão de 16 ± 18 µm. Foi realizada a caracterização microestrutural com o auxílio das técnicas de microscopia eletrônica de varredura (MEV) e de difração de elétrons retroespalhados. O refinamento microestrutural foi realizado eficientemente alcançando uma microestrutura fina, observou-se uma redução de 80% alcançando um tamanho de grão de 3,38 µm, e um aumento da fração de contornos de alto ângulo passando de 23% a 46%. A partir dos resultados obtidos nas análises conclui-se que os mecanismos responsáveis pela evolução microestrutural foram os processos de subdivisão por meio de fragmentação e rotação de grãos, recuperação e recristalização dinâmica.

Aug 16, 2017

By Gualberto Salas Torrelly

El avance tecnológico en los sistemas de iniciación en voladura abarca desde el sistema convencional (Mecha de Seguridad y Fulminantes hasta el sistema de iniciación electrónica, donde a través de un control de vibraciones se controla la energía liberada en un disparo, optimizando la fragmentación y disminuyendo el daño a las paredes del pit. En ese sentido, el sistema de iniciación con detonadores electrónicos, fija con claridad los conceptos de precisión, flexibilidad y seguridad. Por ello, el presente trabajo señala el uso de detonadores electrónicos por la Sociedad Minera Cerro Verde con la finalidad de evaluar sus resultados en seguridad, precisión, fragmentación, vibraciones, y control de daño a las paredes de la mina. Los resultados fueron óptimos -en tanto mejoró la fragmentación, el proceso de carguío y se incrementó el flujo en chancado primario.

Sep 12, 2005

By O. Leuangthong, M. Nowak

"The impact of high-grade data on resource estimation has been a longstanding topic of interest in the mining industry. Concerns related to possible over-estimation of resources in such cases have led many investigators to develop possible solutions to limit the influence of highgrade data. It is interesting to note that the risk associated with including high-grade data in estimation appears to be one of the most broadly appreciated concepts understood by the general public, and not only professionals in the resource modelling sector. Many consider grade capping or cutting as the primary approach to dealing with high-grade data; however, other methods and potentially better solutions have been proposed for different stages throughout the resource modelling workflow.This paper reviews the various methods that geomodellers have used to mitigate the impact of high-grade data on resource estimation. In particular, the methods are organized into three categories depending on the stage of the estimation workflow when they may be invoked: (1) domain determination; (2) grade capping; and (3) estimation methods and implementation. It will be emphasized in this paper that any treatment of high-grade data should not lead to undue lowering of the estimated grades, and that limiting the influence of high grades by grade capping should be considered as a last resort. A much better approach is related to domain design or invoking a proper estimation methodology. An example data-set from a gold deposit in Ontario, Canada is used to illustrate the impact of controlling high-grade data in each phase of a study. We note that the case study is by no means comprehensive; it is used to illustrate the place of each method and the manner in which it is possible to mitigate the impact of high-grade data at various stages in resource estimation."

Jan 1, 2015

By E. H. Jr. Dix

THE use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong-aluminum alloys, magnesium is present to the extent of ½ to ¾ per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth1, 2,3,4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high purity aluminum manufactured by this company .5

Jan 1, 1929

By M. Hesham El Naggar, Yasser Abdelghany

"ABSTRACT: The axial and lateral monotonic and cyclic behavior of helical pile foundations was investigated and new innovative helical screw systems suitable for seismic loadings were developed and patented. More than one hundred full scale field load tests were conducted on instrumented helical screw piles installed in cohesive soil. The piles included: plain helical screw piles (P-HSP); grouted (G-HSPs); fiber reinforced polymer FRP-G-HSPs; and reinforced grouted RG-HSPs. The RG-HSP piles axial capacity was more than twice that for P-HSP, with minimal reduction after cyclic loading, and their lateral capacity was more than 3 times the P-HSPs capacity. A 3-D finite element model was established. The results of 3-D finite element modeling were used to establish the load transfer mechanism and a design methodology for the considered piles.INTRODUCTION AND LITERATURE REVIEWHelical (screw) anchors have been utilized in tension loading and have gained popularity for bearing load applications. Helical piles represent an overall cost effective alternative to conventional piles for new construction and repair applications. The helical piles speed and ease of installation, less noise during installation added advantage with regards to their efficiency and reliability for underpinning including re-support and reconstruction of distressed and damaged foundations for either stabilization or rehabilitation. The “square shaft” SS175 pile is a segmented deep foundation system with helical steel bearing plates (helices) welded to a central steel shaft. Load is transferred from the shaft to the surrounding soil through these bearing plates. Segments or sections are joined with bolted couplings. Practically installed depth is limited only by soil resistance and economics. A helical bearing plate or helix is one pitch of a screw thread. All helices regardless of their diameter have a standard 75 mm pitch (Figure.1). The performance of single helical anchors and group action were studied experimentally and theoretically by several researchers, the researches focuses on the installation torque and uplift resistance. Some researches focus on the load carrying capacity with little pile response to cyclic loading effects or to instrumented full scale field testing. Helical piles axial compressive or lateral loading still is not well characterized and needs more analyses and their seismic performance was not investigated. For such this research was initiated to investigate the helical piles monotonic and cyclic performances under axial and lateral loadings to consider their usage in different applications in seismic zones. Among the several researchers, Clemence (1983); Mooney et al. (1985) conducted field and laboratory testing; Hoyt (1989), Hoyt et al. (1995), and Ghaly and Clemence (1998) conducted theoretical and experimental testing, Puri and Vijay (1984), Huang et al. (1995), Perko (2000), and Pack (2000) conducted theoretical analyses. Rao and Prasad (1993), Prasad and Rao (1994), conducted experimental testing; Vickars and Clemence (2000) studied the performance of helical piles with grouted shafts."

Jan 1, 2014

By Everson P. T, Moyle F. J

Magnesite-rich and dolomite-rich ores from the Savage River region of Tasmania are being considered as potential feed material for a commercial process for production of magnesia.Two selected samples have been characterized by chemical analysis, X-ray diffraction, and differential thermal and thermogravimetric analysis. The materials differ in calcination behaviour, with magnesite decomposing at a significantly lower temperature than dolomite. Calcination conditions have a marked effect on the rate and percentage of magnesium dissolved as the bicarbonate when slurries of the calcine are leached with carbon dioxide. From a process point of view, the feed should have the highest possible magnesite/dolomite ratio, while the optimum calcination conditions are determined by the behaviour of the magnesite component of the feed.From batch calcination tests, it is apparent that the optimum calcination conditions for magnesite-rich ore are a temperature in the vicinity of 700°C and a calcination time of one hour.

Jan 1, 1981

By F. L. Pirkle

A heavy-mineral deposit about 1.6 kilometers (I mile) in length and averaging about three meters (10 feet) in thickness is exposed approximately130 kilometers (80 miles) east of Denver, along Interstate 70, in Elbert County, Colorado near the town of Limon. The deposit is exposed in a geomorphic feature known locally as Titanium Ridge. The dominant heavy minerals, accounting for about 70% of the total heavy mineral suite by weight, are ilmenite, garnet, and zircon. The mineralized zone appears in a series of visually interpretable facies that are stacked vertically and represent subtidal, forebeach, backbeach, washover fan, and aeolian depositional environments. These paleoenvironments are analogous to depositional environments represented by a modern heavy-mineral bearing facies tract on St. Catherines Island, Georgia. Thus, Titanium Ridge provides evidence that heavy-mineral accumulation models for late Cenozoic deposits in the Georgia and Florida coastal plains are applicable to heavy-mineral deposits of the Western Interior subsurface and, by implication, the Western Interior Seaway, extending from Mexico to the Canadian Arctic.

Jan 1, 2011

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not generally been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. miners are required to have annual safety training, but they rarely view this positively. In fact, it has been called “safety jail” by many of them, who regard it as a time to get a little extra sleep. The challenge then, was to find a way to develop effective safety training for these people, particularly in view of the fact that their work is among the most dangerous of all occupations. Miners are born story tellers. They share “near-miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environ-ment, they also instruct listeners in the culture of mining and the values it embraces. Stories, it seems, are a way to get safety messages to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how the training videos created to get safety messages to miners were developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

Spreadsheet Based Modelling of Liner Wear Impact on Charge Motion in Tumbling Mills

Sep 13, 2010

Cobalt mostly occurs as a minor, but valuable, constituent in most nickel and a few copper ores, however it is not generally found alone in commercially viable deposits. Its concentration and extraction are therefore intimately linked to the recovery of the primary metals and the major task for the metallurgist is to extract cobalt of commercial grade from a much larger mass of either nickel or copper and sometimes both. With a particular focus on Vale Inco?s operations, this paper provides a brief overview of the mineralogy of the main deposits being currently exploited that contain cobalt as a co or by-product. The concentration and then extraction to metal are reviewed and some advances released into the public domain are discussed.

May 1, 2009

By Dale R. Spangenberg

This Bureau of Mines Information Circular on phosphate is one of a series of minerals availability commodity directories. Nonconfidential information from the Minerals Availability Program data base covering 148 domestic and 103 foreign phosphate properties and deposits has been abstracted for use in this directory. Abstracts include applicable data on location, published reserves and resources, geology, mine and beneficiation systems, and operational information.

Jan 1, 1983

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By Miezitis Y

A weak airborne radiometric anomaly was examined in the field and the presence of uranium confirmed. Rotary-percussion drilling showed the presence of uranium but a subsequent programme of diamond and rotary percussion drilling indicated that the concentration of uranium was uneconomic. Within the tufts and volcanics of the prospect the uranium existed as uranyl phosphates within the oxidized zone. Geological mapping and the diamond drill core showed that the Stag Creek Volcanics are part of the Lower Proterozoic Masson Formation, probably with member status, rather than the expression of an Archaean basement ridge. This change in the interpretation of the fundamental structure of the Pine Creek Geosyncline has led to a reexamination of the stratigraphy and to suggestions which differ from the current concept.

Jan 1, 1977

By O. S. L. Bruinsma, M. J. Matsela, D. J. van der Westhuizen

The free ligand (FL) model is an intuitive model to calculate the equilibrium concentrations in solvent extraction (SX) based on the distribution coefficient (Kd) at infinite dilution and the fraction of free ligand available for extraction. In this work, the FL model is validated to account for co-extraction of Ni and for designing the extraction and scrubbing sections of Co/Ni separation in a base metal refinery. Cyanex 272 is employed as a selective Co extractant in the process to yield high purity Ni. To enhance the loading capacity of the extractant, 50 mol% of NaOH is pre-loaded into it. Experimental and FL modelling results show that four equilibrium stages are required to purify the 99% Ni feed to a 99.97% Ni raffinate. The 53.59% co-extract with 26.76% free ligand is purified with a reflux scrub of 30 g Co/L in one equilibrium stage to 99.01%, Co in the scrubbed extract. The FL model as well as the Co/Ni/Na-analysis of the aqueous phase confirm that in the scrubbing section, Ni in the extract is mainly replaced by Co. Finally, in the one stage stripper the Co concentration in the scrubbed extract is increased from 5.6 g Co/L in the extract to 30.5 g Co/L that is partially used as reflux scrub liquor.

Dec 11, 2024

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942