Search Documents

By J. B. Fletcher

The Miami mine first started operations in 1910. For convenience, the history of the orebody can be divided into the following categories (Fig. 1): 1) 1910 to 1925: 24.4 million tons of high grade ore, mined by top slicing, sublevel caving, etc. 2) 1926 to 1954: 102 million tons of low grade ore, mined by block caving.

Jan 1, 1961

By D. DePaoli, P. Zhang

"Phosphate ore is one of the most significant secondary resources for rare earth elements (REEs), and Florida phosphate is of particular interest due to its much higher ratio of heavy REEs, especially yttrium. Analyses of numerous samples from different phosphate processing streams in Florida showed that heavy REEs account for about 50% of the total REEs in Florida phosphate with yttrium accounting for approximately 30%. It was estimated that the amount of yttrium from US phosphate processing could meet the world demand for this critical element. This research aimed at recovering both REEs and phosphorus from a phosphate flotation tails. This tails is composed of mainly silica and phosphate with a small fraction of heavy minerals including monazite and xenotime. Since the specific gravity of silica is 2.6 versus 3.2 for phosphate and 4.5-5 for rare earth minerals, pre-concentration of the minerals of interest by gravity separation was investigated first. A pilot scale shaking table was used in this study. One pass gravity concentration achieved a shaking table concentrate analyzing over 600 ppm REEs at about 40% recovery. Flotation of the shaking table concentrate resulted in a product containing 1809 ppm REEs and 26.37% P2O5 with corresponding recoveries of 73% and 82%. Sulfuric acid leaching at 75oC could recover over 60% REE and nearly all the P2O5. Higher REEs (>90%) recovery was achieved by conducting leaching at higher temperature with concentrated sulfuric acid. The phosphoric acid from leaching of the flotation concentrate is of superior quality compared with that generated from regular phosphate rock.INTRODUCTION Rare earths are a group of 17 elements including those of the lanthanum series, as well as the non-lanthanides, yttrium and scandium. These elements have very specific critical uses in a multitude of markets. For example, lanthanum is used as a catalyst in breaking down crude oil to produce gasoline, diesel and jet fuel and neodymium is the core magnetic component in high-strength magnets for electric car batteries, wind turbines and hard disk drives. Rare earths are also essential for many military applications. Many of these applications have no substitute materials and the move to green technologies has dramatically increased their demand."

Jan 1, 2018

By A. Fuerst

The recent seismic events have shown that earthquakes have an immense destructive power. Chile was hit in February 2010 with a seismic intensity of 8.8 on the Richter scale, and had loss of about 700 killed persons, while Haiti was hit in January 2010 with 7.0 killing about 220?000 people. The event in Haiti showed that the seismic events can lead to a disaster if no preventive measures are taken. On the other side, the seismic event in Chile has hit a well-prepared country with moderate consequences. The earthquake with 6.6 Richter in Japan in March 2011, have further shown how severe the consequences can be if critical equipment is involved. Fortunately, the equipment in a mine has not the potential hazard as a nuclear power plant. Anyway, we are diligent and it is obvious that the seismic risk may lead to a real disaster even if the probability is small. The GMD is an important component in the grinding circuit of a mine. This paper maps out earthquake-prone areas including expected earthquake magnitude calculated according to relevant standards, focusing mainly on the building code IBC 2009. An overview is provided on how this standard is applied to mining equipment to minimize damage and aid large mills in operation to successfully withstand seismic effects. The differences in stresses and forces on the GMD and foundation are shown based on a turning and stopped mill simulation during an earthquake. The results demonstrate the need to maintain active and operating earthquake detection systems. Aside from detecting an earthquake?s magnitude, the sensor information can also be used to reduce the harmful effects that an earthquake has on mining equipment. As follows the earthquake requirements are defined. The last part of this paper explains how to fullfill these requirements.

Jan 1, 2012

By W. F. Boericke

AT Kellogg, Idaho, J. Fred Johnson is driving the 5000.-ft Hooper Tunnel under contract for the Bunker Hill & Sullivan Mining Co. This was visited by a group of engineers during the recent meeting of the A. I. M. E. at Spokane, who were impressed with several features of the work. An excellent record of advance is being made by the contractor, over 47 ft. being driven in 3 days during October, and 223 ft. advanced in 29 shifts. The size of the tunnel is 8 by 9 ft. The ground is Wallace quartzite and, save for the first hundred feet, stands well and does not require timbering. The grade is held uniformly at 0.5 per cent. Two shifts are employed, with two sets of machine men to the shift. Ingersoll-Rand S-70 drills are used. each machine being set up independently in the heading; 26-30 holes are drilled to the round; using 1 1/4: in. round hollow drill steel. A 7-hole cut is required, and these holes are blasted simultaneously, using 60 per cent gelatine, 12 sticks to the hole. Instantaneous and fire delays of electric detonators are used for the complete round. A feature of the drilling is the use of long carriage drills, necessitating fewer changes of steel, and more time spent on drilling, with less time consumed taking steel back and forth from the face. Of course, this means better blacksmithing so that the drill steel shall stand up for the added footage.

Jan 1, 1930

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008

The sulphides can be arranged in a series determined by the relative amounts of ionic and covalent bonding present. This series is similar to the paragenetic series common to most sulphide ore deposits. Investigation of the surface tensions of the corresponding heavy metal iodides by the maximum bubble pressure method throws some light upon this relationship. It is shown that the surface tension of molten iodides decreases as the chemical bonding within them becomes more covalent. These results are interpreted in terms of the constitution of the melts, and are extended to cover the case of sulphides in solution in a silicate melt. It is concluded that sulphides tend to lower the surface tension of silicate melts and that this tendency becomes greater as the bonding within the dissolved sulphide groups becomes more covalent. A possible relationship between this conclusion and the origin of paragenesis in sulphide ore deposits is indicated.INTRODUCTIONIt is well known that the order of deposition, or paragenesis of sulphide minerals is remarkably similar in hypogene ore deposits throughout the world. This widespread similarity points towards the operation of some fundamental process which must be intimately connected with -the genesis of these ores. A correct interpretation and understanding of the causes of paragenesis in sulphide ore deposits would shed much light on the origin of these deposits.In Table 1 a simplified paragenetic series for sulphide minerals is presented. In most cases, only the most important sulphide of any particular element has been included. The object of this procedure is to simplify the following discussion. Furthermore, it should be realized that this series is only a generalization and that exceptions and reversals of position are quite common. Especially does this...

Jan 1, 1956

By M. van Schoor

Coal remains South Africa?s most abundant and cheapest source of energy, and there is an ever-increasing necessity for optimal and safe extraction of the remaining reserves. Increasing focus on cost-effective mining and zero harm to the environment and miners has resulted in a shift in attitude towards the application of geophysics in local coal mining and exploration. Furthermore, technological advances have contributed to geophysics being embraced more readily by the coal mining industry, compared to a decade or two ago. Predictably, the growing interest in geophysical technologies has also created a need for education and training in the basic principles and application of geophysical methods, as local coal mining companies generally do not have in-house geophysicists. Consequently, the Coaltech Research Organisation?s Geology and Geophysics working group forum compiled a textbook aimed at addressing this need: to produce a guide for applying geophysics to coal mining problems in South Africa. The target audience for such a book would be coal geologists, mine surveyors, mine planners, and other mining staff with limited or no geophysics background. This paper provides a very brief overview of the book by summarizing key sections and selected examples. In doing so, the value of geophysics to solving a range of coal mining and exploration problems is highlighted.

Jan 1, 2014

By C. C. Anderson

"While conducting investigations in connection with the helium program of the Bureau of Mines, the Cryogenic Laboratory has improved an apparatus for the rapid and accurate determination of the helium content of natural gas and gaseous mixtures derived from that source. The separation of helium is effected by the use of activated coconut charcoal which, when cooled to liquid-air temperatures, absorbs the nitrogen and other constituents of the gas, leaving the helium in a. spectroscopically pure state. This absorptive property of activated charcoal was discovered- by Dewar3/ in 1875. Several years later, while conducting their original researches on helium in natural gas, Cady and McFarland employed the charcoal method for the absorption and removal of the common constituents of natural gas and constructed an efficient apparatus in which this operation could be effected.4/ Shortly after initiating the government's helium activities during the World War period, the Bureau of Mines adopted, with Minor modifications, the Cady and McFarland apparatus and method of analysis. Seibel.5./ described this modified apparatus and method of procedure as part of a publication on helium-bearing natural gas. Subsequently, the Bureau's apparatus for helium analysis has been simplified and improved to facilitate more rapid and positive operation. The apparatus and method of procedure now being used by the Bureau of Mines Cryogenic Laboratory arc described in this paper.The personnel of the Bureau of Mines Cryogenic Laboratory has improved and brought the helium apparatus described herein to its present state of perfection. The writer's contributions have been-of minor importance, and he wishes to give the various members and former members of the laboratory staff full credit for the improvements they have made. He also desires to express his appreciation for suggestions and criticisms offered during the preparation of this paper to the following members of the Petroleum and Natural Gas Division, Bureau of Mines, which now includes the Amarillo Helium Plant and Cryogenic Laboratory: H. A. Cattell, chief engineer; C. W. Seibel, supervising engineer of the Amarillo Helium Plant; W. M. Deaton, chemist-in-charge of the Cryogenic Laboratory; and H. S. Kennedy.The quantitative determination of helium in a gaseous mixture is accomplished by the removal of the other constituents from the sample, either by chemical or physical Means, leaving only the helium which can be measured directly. Chemical methods, when applied to natural gas, require the burning of the hydrocarbons in oxygen, the, absorption of the resulting carbon dioxide in a caustic solution, the removal of the excess oxygen in a suitable solution such as an alkaline pyrogallate, and the elimination of nitrogen by sparking or by combination with hot calcium or magnesium.. Such procedures are very slow and tedious compared with the physical method which employs the absorptive property of activated charcoal to effect the separation of the other constituents from the helium."

Jun 1, 1934

By W. J. Kroll

Jan 1, 1960

Jan 1, 1989

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

By Robert Keyes, Charle Knowles, Glenn Kendall, Gary Fletcher

"The metal mining industry in Canada has been dramatically affected by the changes that have occurred in the world mineral market place. World economic restructuring in the post ""oil shock"" period of the mid-1970s, greatly increased competition from suppliers in the developing countries, and commodity price and currency pressures have all combined to severely test Canadian competitiveness. In the new mining world, the rate of growth of demand for metals has declined due to product downsizing, materials substitution, and a relatively slower growth of over-all world economic activity.The interplay of market and political factors is complex. Canadian metal mining companies must compete in world markets against low-cost producers in developing nations whose priorities often appear to be centred on maximizing foreign exchange earnings to foster development goals and debt repayment. Many of these countries have high levels of government intervention in their mining industries. The result is a greatly in-creased number of suppliers all vying for a share of a world demand growing at a relatively slower rate than in the past. To be able to compete under these circumstances, Canadian companies have had to undertake 'survival mode' measures and look to new ways of doing things. In order to identify the effects that the recent market and economic trends have had on the Canadian metal mining industry, a study was undertaken by Canada Employment and Immigration to assess these changes and their implications for the metal mining workforce.The Canadian Occupational Projection System (COPS)—Sector Study Group with the cooperation of the Mining Association of Canada, undertook a human resource survey to gather current employment and occupation information. This formed an important part of the Canadian Occupational Projection System Metal Mining Sector Study. This article addresses the with survey results, a C.E.I.C. worker mobility study, and trends and issues that are changing the mix of jobs and the way they are being done.Figure 1 shows metal mining employment for the period from 1974 to 1984. It provides a clear picture of the employment swings that the industry has experienced especially during the recession period of 1981 to 1983. From 1981 to 1983, employment dropped by 14 000, from 68 000 to 54 764, and then dropped to its lowest point in 1984 of 52 783. We feel that employment in the medium term will be flat with growth in gold mines being largely offset by continued workforce rationalizing in other sectors.Perhaps the key point is that equivalent levels of output have been achieved in the recent period (1981-1984) with a workforce that is 25% smaller than it was in 1974. This also raises the questions which the COPS/MAC survey and COPS mobility study sought to clarify, namely, what jobs have been cut and where have these people gone? Equally important are the questions of occupational skill level changes, and what types of jobs are declining and which ones are becoming increasingly important, as economic and technological changes have altered the mining work place."

Jan 1, 1987

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By N T. Moxon, L W. Armstrong

Explosive manufacturers have for many years provided a service to the mining industry which has,until recently, been unchallenged by mine operators. Today mine operators are more aware of the properties of explosives required to perform particular tasks within their operations. These properties can be reliably quantified using the test procedures described in this paper for emulsion adn ANFO based explosives. Details of an end-user sampling programme desgined to provide quality checks on explosives supplied to a mine site are also discussed.

Jan 1, 1991

By Robert Vergie

Like most of you, I would rather work on a job than talk about it. But it is fruitful to spend some time taking stock of important developments in the heavy construction field. One of the strongest recent movements affecting the industry has been the push for safety. I regret that it is a recent development. Not that builders were against safety. Too often though, it was easier to continue with dangerous old work methods than to try something new. Too often, it was easier for equipment manufacturers to build production tools with little consideration for worker safety. And too often, accidents and gruesome disasters occurred. The ultimate result of on-the-job injuries in construction and other industries was the Federal Government's Occupational Safety and Health Act of 1970. Individual states were required either to accept OSHA or pass updated regulations at least as stringent as the Federal requirements. These new rules must be strictly obeyed -- not just because they carry civil and criminal sanctions -- but because they correct unsafe conditions and reduce hazardous acts. Though some OSHA measures have been criticized as superfluous, most of them do in fact save lives and limbs. Equally important, the tunneler who follows the new safety regulations can be fairly certain of an efficient, uninterrupted operation. Regulations do sometimes bring rewards.

Jan 1, 1974

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several stages —basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP increased by 3.5 percent from 2004 to 2005. The nominal GDP was $12.5 trillion at the end of 2005. Housing starts were up by more than 5 percent for the year, and the unemployment rate decreased to 5.1 percent in 2005 from 5.5 percent in 2004. The prime interest rate increased from 5.25 percent at the beginning of the year to 7.25 percent at the end of the year. The value of minerals mined in the United States in 2005 rose significantly because of increased unit prices for some metals —particularly molybdenum — and significantly increased production for some industrial minerals, mainly cement, construction sand and gravel, and crushed stone.

Jan 1, 2006