Search Documents

By Arthur Darby

The city of Kuala Lumpur was founded in 1857 by miners seeking tin near the confluence of the Klang and Gombak rivers. The rapid development of the city and surrounding area since independence has led to more rapid runoff during rainstorms and to gradual canalisation of the rivers with some restricted sections. The outcome has been more frequent and more severe floods (Abdullah 2006). At the same time the centre of Kuala Lumpur has become a modern inter-national city with tall office buildings, hotels, and shopping centres connected by a network of wide roads and commuter rail systems. With these the cost of dislocation during floods has risen as has the cost of making good damage afterwards. The Government of Malaysia considered these consequences unacceptable and sought ideas from the private sector for a solution. Potential solutions consisted of variations on the themes of bypassing the city centre with a flood relief tunnel or of providing off channel storage or a combination of both. Since under Malaysian law a tunnel cannot be constructed under private property unless this is first purchased or agreement reached with the owner, it was necessary for most of the tunnel alignment to run below existing heavily congested roads. After considering these facts Gamuda Berhad and MMC Berhad, two leading Malaysian development and construction companies, decided to propose to Government an innovative solution in which the tunnel would be used to carry road traffic except during floods.

Jan 1, 2008

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By A. K. Majumder

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of coal fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of coal fines. The results obtained from this study revealed that among the parameters studied, drum rotation and feed solids concentration play dominating roles in controlling the yield and ash content of the clean coal. Mathematical modeling equations that correlate the variables studied and the yield and ash contents of the clean coal were developed to predict the performance of an MGS under different operating and design conditions. The entire exercise revealed that the MGS could produce a clean coal with an ash content of 14.67% and a yield of 71.23% from a feed coal having an ash content of 24.61%.

Jan 1, 2007

By G. S. Hansford, C. J. N. Dempers, G. E. Searby, A. W. Breed, M. A. Jaffer

The bioleaching of sulfide minerals involves a ferric attack of the mineral with the role of the micro-organisms being the oxidation of the ferrous-iron back to the ferric form, and the oxidation of sulfur, either via thiosulfate or polysulfides, to sulfate. The kinetics of bacterial ferrous-iron oxidation and the chemical ferric leach kinetics of sulfide minerals can both be described as functions of the ferric/ferrous-iron ratio. The independently determined bacterial ferrous-iron oxidation and chemical ferric-iron leaching kinetics have been successfully used to predict continuous bioleaching operations.

Jan 1, 2000

By Fábio Luiz dos Santos

As ligas de alumínio, em particular, apresentam certas restrições quando submetidas ao processo de união por soldagem. Isto se deve, principalmente, por apresentarem elevada condutividade térmica, elevada contração na solidificação e elevada solubilidade de hidrogênio. Levando em conta estes aspectos, o processo de soldagem FSW apresenta grande potencial para esta aplicação, visto que, é autógena, realizada sem fusão do material e sem utilização de escórias ou gases de proteção. A partir deste conceito, o objetivo do presente trabalho é avaliar a união de chapas finas de alumínio da liga 3105 H26, com espessura de 0,7mm. Para realização dos testes, foram analisados fatores como: penetração da ferramenta nas chapas processadas, ângulo de ataque, tipo de ferramenta e modo de controle de penetração (posição ou força). Os resultados indicaram que o modo de controle por força se mostrou o mais indicado para chapas finas, e que o regime transiente no início de soldagem foi a parte mais crítica para controle da qualidade da junta soldada.

Aug 16, 2017

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By M. Andrews, B. J. Göhre, G. Strong, C. Terblanche

Mechanized mining can be experienced as a symphony by substituting the instruments for the different machines that each perform their own function and thus have different sounds. The drill-rig is the soloist around which all the other machines must play their part in harmony. Each machine can function on its own, but productivity is achieved only when all of the machines function in a holistic manner, as the different sounds of instruments form a symphony when playing together. To produce a symphony is to have the ability to put together all the pieces. It is the capacity to synthesize rather than to analyse. Today?s managers have to apply this harmonic way of thinking to make the system of mechanized mining work. In other words each of these people must have the ability of a conductor, whose job involves corralling a diverse group of notes, instruments and performers, and producing a unified and pleasing sound. At Modikwa Mine the introduction of the MAPS (Mine Activity Performance System) has allowed management to obtain a clear view of all the activities associated with the equipment. Through synthesis the issues that hampered productivity were identified and addressed to improve production and reduce costs.

Jan 1, 2006

By Taylor G. H

The Triassic Ipswich (SE. Queensland) coals are of bituminous rank. The more exact rank of individual samples was determined by measuring the reflectance of the vitrinite. While in general the rank of the coals increases with stratigraphic depth, minor reversals, probably related to igneous intrusions, occur.The Ipswich coals form a coherent group so far as petrographic type is concerned. All are comparatively rich in vitrite and clarite, cutinite being the common maceral of the exinite group. The mineral contents of all the coals are comparatively high, clay and quartz being most abundant. The coals appear to be of essentially autochthonous origin, and to have been formed under conditions of fairly rapid subsidence.While the use of the coals is at present restricted to combustion, most have pronounced coking properties, as would be predicted from their petrographic composition and reflectance. However, the high mineral content of the coals would be a limiting factor in their use for coke-making.INTRODUCTIONDuring the last ten years, the Division of Coal Research, Commonwealth Scientific and Industrial Research Organization has carried out an extensive investigation of Australian coals, providing a wide range of analyses of most of the important of them. Special attention has been given in recent years to Queensland coals.Most seams were sampled as a number of subsections, enabling the internal variations, as well as the overall properties, to be assessed. The lenticularity of many of the mineralrich layers may tend to limit the significance of the samples, particularly in respect of ash yield, but although the vertical distribution of mineral matter may vary considerably from one sampling position to another, the lateral variation of the total mineral matter in the whole seam may not be great.Apart from extensive chemical analyses and utilization...

Jan 1, 1963

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

In this study, the oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bismuth (Bi), lead (Pb), antimony (Sb), arsenic (As) and copper (Cu) contents in the speiss by two-step simulation differed from the industrial data by 0.6, 0.8, 2.6, 7.2 and 8.6 weight percent, respectively. The two-step simulation results indicate that the speiss partitioning of Sb, As and Cu increased from 60.1, 32.3 and 27.5 percent to 81.6, 67.8 and 47.2 percent, respectively, with the smelting temperature increasing from 1,050 to 1,250 °C, while the metal partitioning of Sb and Cu increased from 0 and 2.7 percent to 15.2 and 13.3 percent, respectively, with the separation temperature increasing from 400 to 700 °C.

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By N. Behnood

"This paper describes how material selection, quality assurance, and failure investigation play important roles in the efficiency and safety of mining and metallurgical operations.INTRODUCTION Material selection, quality assurance, and failure investigation are all complementary elements of materials engineering in the application of materials technology for failure prevention. Based on commodity price increase of 300% between 2002 to 2013 [1] and increased cost ofcapital projects and operation, equipment failure, which in some cases causes complete shutdown of the operation, becomes a vital importance in mining and metallurgical plants. The following sections present a number of examples from many failure cases experienced by the author during his three decades of work as a materials engineer in the mining industry."

Jan 1, 2015

By José Eudes Lima Santos

Neste trabalho foi estudado o efeito da variação da densidade de corrente, temperatura e pH do banho eletrolítico na eletrodeposição da liga Ni-Mo-P utilizando citrato de sódio como agente complexante em função do comportamento anticorrosivo da mesma, da composição química e morfologia dos revestimentos. A caracterização das camadas foi feita por microscopia eletrônica de varredura (MEV) e energia dispersiva de raios-X (EDX). Os ensaios de corrosão foram realizados à temperatura ambiente em NaCl 0,1 M por polarização potenciodiâmica linear (PPL). Como ferramenta de otimização foi utilizado um planejamento fatorial completo 23 associado a metodologia da superfície de resposta (MSR). As propriedades de corrosão e composição química dos revestimentos de Ni-Mo-P obtidos mostraram ser dependentes da densidade de corrente, temperatura e pH do banho eletrolítico. A ausência de trincas foi verificada para revesimentos com baixo conteúdo de molibdênio e mostrou ser necessário para obtenção de eletrodepósitos com boas propriedades de resistência à corrosão. Os resultados revelaram que o revestimento que apresentou melhor resistência à corrosão foi obtido em densidade de corrente 100 mA cm-2, temperatura de 40°C e pH 9,0 com composição de 87 wt.% Ni, 6 wt.% Mo e 7 wt.% P e sua superfice exibiu morfologia nodular.

Aug 8, 2018