Search Documents

By R. Colás, A. Salas, M. P. Guerrero Mata, R. Garza

"The use of the finite element method (FEM) for studying the plastic behavior of metals has become a common practice over the past few years, because it has been proved to be a good means of evaluating processes parameters, and predicting and improving processes, avoiding the traditional trail and error technique. FEM was used via a commercial package (Abaqus) to create two dimensional models to simulate uniaxial tensile tests for a galvanized low carbon steel. The aim of the work was to analyse the plastic behaviour of a distribution of grains on the zinc cover of a set of galvanized low carbon steel samples. A mesh with lines 2 mm apart was drawn on one of the faces of the samples that were deformed at room temperature, at constant crosshead speed, stopping the deformation at different times. Before and during the stops the deformation measurements were recorded for further calculations in an image analyser in order to compare these with computational predictions, as well as validate the numerical model. The results of this study can be extended to other testing conditions, besides the model can be used for obtaining constitutive equations of the materials.INTRODUCTIONThe use of the finite element method has been widely spread during the last two decades in most engineering areas, it is a good means of obtaining approach values at a first try [1-4]. Thanks to the software and hardware developments it is now possible to run huge problems within hours or minutes, making the technique more accessible and useful for the industry.The aim of this work is to create a finite element model for the uniaxial simple tension test, and compare the results with some experimental results, and asses the validity of the model.The plastic behaviour of the materials with FEM has been studied for a long time [5] and there is always something new to learn about this behaviour of the metals in particular, as well as to characterized new materials and alloys [6,7]. The tension test has been used since XIX century to get knowledge of the materials [5,8], it is the test that has been used the most and the only that is fully standardized, although it has the limiting of low strains, it is still the most widely used, especially in the industry.Two different finite element models in two dimensions (2D) have been developed, one called the mesh model and the other one the grain model, attention was focused on the geometry and strain prediction. The model is validated with experimental test, by using the data and directly comparing it with the numerical predictions. All the tests were carried out at the same constant crosshead speed at room temperature. An analysis of the grid distortion using FEM and analytical methods has been carried out."

Jan 1, 2001

By A. Navarra

Peirce-Smith converting (PSC) is applied for roughly 50% of primary nickel and 70% of primary copper production. PSC cycles produce batches of ironfree sulfide matte (or blister copper, in the case of copper smelters), that are subject to further processing. However, the number of cycles that can be performed simultaneously is limited by the offgas handling system. Moreover, PSC suffers from variation in the yield and duration of the cycles. This variation is managed by conventional smelter designs, in which the upstream smelting capacity exceeds the nominal converting capacity; PSC is thus a major bottleneck in conventional nickel and copper smelters. Stabilization and standardization of PSC operations can therefore increase smelter throughput. The current paper presents a discrete event simulation (DES) framework to assist in smelter debottlenecking. It features random number generation to represent cycle variability, and time-adaptive finite differences to represent thermochemical complexity. Preliminary computations are presented.

Arsenic occurs naturally in rocks and soils, water, air, plants and animals. It can be further released into the environment through natural activities such as volcanic action, erosion of rocks and through human actions. Higher levels of arsenic tend to be found more in ground water sources than in surface water sources of drinking water. Compared to the rest of USA, western states have more systems with arsenic levels greater than 10 parts per billion (ppb). The US Environmental Protection Agency (EPA) has historically regulated arsenic in drinking water at 50 ppb, but the agency has lowered the maximum contaminant level (MCL) for arsenic to 10 ppb-to be in compliance by January 2006.This paper reviews briefly a) aqueous arsenic chemistry and removal mechanisms and b) the available treatment processes to attain the drinking water standard of 10 ppb by 2006. The combining of an appropriate removal method with an existing system depends on several factors such as nature of arsenic, the water source, existing plant equipment and processes site conditions etc. The paper also includes one or two case studies from the State of Arizona. Key words: Arsenic, Drinking water, Treatment Technologies

Jan 1, 2005

By Jiang Feng, Zhang Libo, Peng Jinhui, Guo Zhanyong, Ju Shaohua, Lei Ting

The basics of microwave drying process of CuCl residue were studied by comparing the dielectric property of the residue with different moisture contents. The dielectric properties were measured by microwave cavity perturbation method. The dielectric constant and dielectric loss factor of the CuCl residue have a linear correlation with the moisture content. With this relationship, we can realize on-line measurement of moisture content of the CuCl residue by dielectric properties. The microwave drying experiments with different thicknesses (1-5cm) of CuCl residue were carried out, and the heating curve of the materials under different microwave powers (250-450W) was made. From these parameters, an optimized operation parameter of microwave roasting technology, the thickness of CuCl residue filter cake to be microwave roasted should be 2cm , was deduced.

Jan 1, 2015

By T. P. R. de Jong

Dual energy X-ray transmission imaging is extensively applied for safety luggage inspection. Its advantages are its rapid scanning rate (25 to 100 cm/sec) at approximately I mm resolution and simultaneous thickness independent metal identification. This is especially advantageous for secondary scrap metal inspection and automatic sorting. Other applications include metal product inspection, bale control, and waste processing. Recent progress in development of an automatic on-line sorter for bulk solids is presented and discussed. Besides various non-metal applications (solid fuels, wastes etc.) it appeared particularly effective in light metal sorting. As inspection tool better control of difficult to monitor solid bulk streams, batteries, bales and other related metals becomes possible.

Jan 1, 2003

By R. S. Celmer

The distributions of cobalt, molybdenum, copper, and selenium between nickel matte and silica-saturated iron silicate slag have been determined in the region of the metallic saturation boundary, at 1523 K. Results are given as a function of the composition of the coexisting Fe-Ni alloy and the activity of iron in the system. Under strongly reducing conditions, these minor elements display a marked preferential accumulation in the sulphide phase. It is shown that the dissolution of cobalt and molybdenum in slag follows an oxidative mechanism, and distribution equilibria are correlated with the oxygen potential. From these data, the thermodynamic properties of cobalt in nickel matte are computed. Further, comparisons of minor element partitions are made between the nickel and copper matte smelting cases under metal saturation conditions.

Jan 1, 1988

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By Jin Yu, Fang-Qiu Zu, Yun Xi, Li-Na Mao

"According to the behaviors of resistivity-temperature of Cu-Sb70 melt, which suggests a partly reversible temperature-induced liquid structure transitions (LST) could occur in this alloy, in this paper, we investigated the dependence of solidification on the liquid state. Both resistivity and temperature were measured to track solidification process. The results show that the nucleating undercooling of the melt which experienced the LST increased and the solidified time decreased. Meanwhile, the solidified microstructures refined evidently, with the microscopic pattern of primary phase changes from disordered pillarlike dendrites into homotaxic ones. Moreover, it is verified that the microstructures would be different if the reversible part of the LST was restrained. The new phenomena and results reflected in this paper suggest that grasping the rules of melt structure change with temperature before material processing will give help for controlling the solidification more effectively and finally resulting in more ideal microstructures.IntroductionThe structure and quality of liquid alloys have a direct and important influence on the structure, performance and quality of the solidified ones. In recent years with in-depth study of liquid structure, researchers have found that some liquid structure transitions (LST) could occur on dependence of the temperature or pressure [1-5]. And the article [6] reported that a pressure-induced reversible LST was found in liquid triphenyl phosphite, which further confirmed the authenticity of the existence of the LST. Furthermore, in our earlier studies of Sn-based melts using resistivity method, some abnormal structure changes induced by temperature have been found at hundreds of degrees above liqiudus, and these LSTs are partly reversible[7]. This phenomenon has been discussed and it is suggested that the reversible LST in Sn-based melts are related to the short-range ordering (SRO) structures of Sn, which are tetrahedron structure with covalent bonding. However, does this reversible LST exist in other melts too?"

Jan 1, 2012

By Ravinder N. Reddy

Electrochemical capacitors are charge storage devices. They bridge the gap between dielectric capacitors and batteries in terms of energy and power density. Electrochemical capacitors are classified into two types, electrochemical double layer capacitors (EDLCs) and capacitors based on pseudocapacitance. In EDLC, charge is stored at the interface between electrode and electrolyte. Carbon is considered to be prime electrode material for EDLCs due to its many favorable characteristics. In this study carbon materials are derived from thermal decomposition of catechol- formaldehyde polymers and are studied as electrode material for electrochemical double layer capacitors. Carbon electrode surface is characterized using NOVA 1200 gas sorption analyzer. It is also characterized using XRD and SEM. Carbon electrodewaselectrochemically characterized using cyclic voltammetry (CV). A highest capacitance of 110 F/g was observed in 30 wt% H2SO4.

Jan 1, 2006

By K. B. Shedd

Questions regarding possible adverse health effects from exposure to zeolites arose when the inhabitants of two villages in Turkey were found to have high incidences of mesothelioma, a disease generally identified with exposure to asbestos. No asbestos deposits are known in the area, but some fibrous zeolites have been found. Further investigations have resulted in conflicting opinions as to whether fibrous zeolites are related to the high incidence of mesothelioma in Turkey. The U.S. Department of the Interior, Bureau of Mines examined the habits of domestic zeolites by scanning and transmission electron microscopy. Only erionite and mordenite particles possessed acicular to fibrous habits. With the exception of a rarely occurring woolly erionite sample, the fibrous zeolites were not dimensionally equivalent to asbestos.

Jan 1, 1982

By Gabriel Zarate

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 tonnes of copper per year and 5.4 million tonnes of ore per year. Copper production was steadily increased reaching a maximum of 62,239 tonnes in 2012 for an ore throughput of 10,5 million tonnes. In order to get these production and throughput rates, a number of changes have been made in the metallurgical parameters of the plant operation since the start up, among them particle size, heap height, acid addition distribution in curing and leaching solution, leach cycles and pad type. Most of the modifications have been implemented after carrying out extensive column test work programs. The modifications implemented and the results obtained, as well as the test work programs carried out, are discussed in this paper.

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By Lucas Lopes da Costa, Sergio Neves Monteiro, Rômulo Leite Loiola

"Composites with DGEBA/TETA epoxy matrix reinforced with thinner and continuous bamboo fibers stripped from culms were mechanically characterized by tensile tests. Specimens with up to 30% in volume fraction of aligned fibers were tensile ruptured at room temperature. The results showed a steady increase in both the ultimate strength and the elastic modulus of the composites with the amount of incorporated bamboo fibers. The fractographic analysis by scanning electron microscopy showed evidence of moderate adhesion between the bamboo fiber and the epoxy matrix. This fiber/matrix adhesion by interaction mechanism apparently justifies the improved tensile properties of the composites.IntroductionIn recent years polymer composites reinforced with natural fibers, mainly those lignocellulosic obtained from plants, have been subject to extensive research works [1-5]. Environmental, economical, societal and technical advantages of these composites are motivating their substitution for similar polymer composites reinforced with synthetic fibers. In particular, R & D efforts have been conducted aiming to replace glass fibers composites that are comparatively more abrasive to equipments, non-recyclable, more expensive, heavier and toxic [6]. Among the many lignocellulosic fiber composites being investigated, those fabricated with bamboo stripped fibers, i.e., fibers longitudinally cut from the culm, still need information to support possible industrial applications. Several works, however, have been dedicated to bamboo stripped fibers as possible reinforcement of polymer composites [7-17]. These works reported mechanical properties that could markedly vary with the type of polymer matrix, the fiber disposition (if continuous, aligned, short-cut, mat interlayered, etc) and the test condition."

Jan 1, 2011

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By Sergio N. Monteiro

From the leaves of the sisal plant (Agave sisilana) a relatively strong fiber can be extracted and is nowadays being investigated as a possible reinforcement for polymeric matrix composites. For this purpose, it is important to determine the critical length of the fiber with respect to the matrix to be reinforced. This has never been properly done for sisal fibers in polyester matrix. Therefore, this work characterized the critical length of sisal fibers, with different sizes, embedded in polyester capsules by means of pullout tests. The critical length obtained allowed the sisal fiber/polyester matrix interface shear stress to be calculated. The relevance of these values for polyester composites reinforcement with sisal fibers is discussed.

Jan 1, 2009

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By M. A. Cocquerel

The future economic necessity of mining copper ores with a high impurity content and increased environmental awareness will require closer examination of the distribution of arsenic within copper smelting processes. A generalized approach is developed which can be adapted to specific projects for the determination of an overall process configuration to satisfy all requirements in a cost effective manner.

Jan 1, 1983