Search Documents

By K. M. Parida

The kinetics of dissolution of manganese dioxide in dilute sulphuric acid solution have been investigated using iron pyrites as a reductant. The dissolution rate of manganese is independent of the speed stirring but depends upon temperature, particle size, specific surface area of manganese ore, acid concentration, Fe(II) concentration and amount of pyrite. The activation energy is 43.6 KJ/mol and the linear relationship between the rate of dissolution and lido indicates that the reaction is chemically-controlled. The redox reactions of MnO2 with iron pyrites and Fe(II) are the rate-controlling reactions.

Jan 1, 1990

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By Ning Wang, Bing Xie, Hong-Yi Li

"Compared to traditional sodium roasting, calcified roast inhibits chlorine pollution. A vanadium extraction technique based on a calcified roast is especially suitable for vanadium slag with high calcium content. In this report, V205was extracted from vanadium slag by calcified roast followed by acid leaching and hydrolysis precipitation. In optimized conditions, the high silicon low vanadium slag was roasted at 850'C for 2 hours without CaO addition. The roasted materials were leached with 35 % H2SO4 in liquid/solid ratio of 5:1 (mL/g) at 95OC for 4 hours. The extraction of vanadium was as high as 97.66 %. These results are instructive to V2O5 production in industry.IntroductionVanadium slag is produced in converter, sodium salt roasting is the commonly used technique to extract vanadium. In sodium salt roasting, vanadium slag is roasted with sodium salts including sodium chloride and soda as additives, followed by leaching with acidic or basic solution [1]. However, in this process chloride reacts to produce corrosive gases including HC1 andCl2- SO2 and SO3 can also corrode equipment severely and are also an environmental contaminant. The low melting point of sodium salts leads to fusion agglomeration, which blocks vanadium oxidation and thus decreases the extraction rate of vanadium. A large amount of sodium salts consumed as roasting additives increases the production cost. Moreover, sodium salt roasting requires low CaO content in vanadium slag. When the CaO content increases to 1%, V2O5 extraction can amount to 4.7%-9% [2]. For vanadium slag with high CaO content, the sodium salt roasting technique leads to low vanadium extraction rate."

Jan 1, 2012

By J. -S. Park, H. -S. Jeon

This study has been carried out to develop a relatively simple hydrometallurgical process for recovering nickel as nickel sulfate from the spent nickel-cadmium battery residue in which cadmium was removed by vacuum distillation. This residue is composed of 36 % nickel, 20 % iron, and other metals such as cobalt. First, crushing and selective classification were performed to separate iron to produce a nickel-rich product (over 40 % nickel). This product was dissolved in sulfuric acid to obtain a nickel sulfate solution. During the dissolution, nitric acid and air were added to the system to enhance the iron oxidation reaction rate. The free acid remaining in the dissolved solution was neutralized by adding nickel carbonate. Iron was precipitated as iron hydroxide and removed from the solution. The nickel sulfate solution was then fed to a vacuum evaporator to concentrate the solution by evaporation of water and crystallized at around 45°C to obtain nickel sulfate hexahydrate. A recrystallization process could remove other impurities such as zinc and manganese.

Jan 1, 2000

By Paponetti B. . A.

Gold is usually recovered by cyanidation, thiourea leaching and amalgamation, however the efficiency of these technologies, in the case of refractory ores, is low ever when fuie grinding is practised. For example, .if the gold particles are included in sulphide minerals, the leachant cannot reach them, so they are often lost in the tailings. Hence .it is first necessary to break the sulphide crystals by preliminary treatment such as roasting, nitric .acid oxidation, pressure leaching and bacterial oxidation and then apply a conventional extractive technique for satisfactory gold recovery. This paper describes the effect of biological pre-treatment with Thiobacillus ferrooxidans) on the? extraction ? and? recovery of gold by conventional cyanidate. leaching from; a refractory arsenopyrite ore from Golcuck (Turkey).

Jan 1, 1991

By Bora Derin

The partial pressure ratios of sulfur and oxygen for several copper flash smelting plants were derived using the Reddy-Blander (RB) model and predicted dissolved sulfur contents available in the literature. The sulfide capacities (Cs) of six different flash smelting plants (FeO-CuOo.5- CaO-MgO-FeOu-AlO15-SiO2) slags were calculated. The log (PO2/PS2) versus matte grades of various industrial processes was determined. The PO2/PS2 ratio increased with an increase of copper grade. The calculated partial pressure ratios for the copper flash smelting are in good agreement with those of the experimental data.

Jan 1, 2003

By Baozhong Zhao

Experimental results have shown that fluxing with soda ash (Na:zC03) can remove As and Sb from molten copper at the rate of As>Sb, but is relatively ineffective in removing Hi. The rate of impurity removal is controlled by impurity mass transfer in the metal phase. In this paper, a mathematical model was developed to describe the impurity removal phenomena. The model incorporates the effects of molten bath mixing intensity, soda ash feeding rate, oxygen content in the molten copper and soda ash fluxing by surface addition and injection. The model predictions are in good agreement with experimental results and may be used in designing large scale tests.

Jan 1, 1996

By Xuling Chen, Zhiyun Ji, Min Gan, Tao Jiang, Liang Yin, Xiaohui Fan

Straw char exhibited considerably faster burning speed than coke breeze for its porosity, which significantly degraded sinter quality when it replacing coke breeze as sintering fuel. In this investigation, preforming technology has been employed to densify raw straw. The properties of straw char preformed show that its density was increased, and the structure was also densified, which made the difference of combustibility between the straw char and coke breeze smaller. The proper preforming temperature, residence time and pressure were 200℃, 1min and 120MPa respectively. Sinter pot trials show that the product carbonized from preformed straw made the proper replacement ratio to coke breeze increase from 20% to 40%, and the emission reduction of SOx, NOx in flue gas increase from 11.50%, 14.15% to 37.85%, 23.60% respectively, compared with non-preformed straw char.

Jan 1, 2015

By Joni M. Barnes

A strain of Pseudomonas stutzeri isohted from selenium contaminated surface waters, was found to be effective . in reducing selenate (Se04 2) stoichiometrically to selenite (Se03 2 '), which was further reduced to elementaJ selenium (Se0 ). These reactions were concurrent with the microbial oxidation of lactate. In order to assess quantitatively the amounts of seilenate and selenitein solution, improvements to existing analytical methods (ion exchange chromatography and inductively coupled plasma atomic emission spectrophotometry technique) .were made.

Jan 1, 1991

By Zhongning Shi, Ramana G. Reddy

"By cyclic voltammetry and potentiostat electrodeposition using Potentiostat/Galvanstat, electrochemical behavior on Ag electrode in electrolyte 0.2M NaOH+0.01MPb(NO3)2-0.01M TeO2 -0.01M TlNO3 solution were also carried out at 298K. The processes of electrodeposition of Tl2Te3 and PbTl4Te3, a thermoelectric material, are reported along with analysis of the composition of the obtained deposits. The results showed that two different underlying processes are occurring depending on deposition potential. One process involves the reduction of TeO3 2- and Tl+ to Tl2Te3 in a potential interval of -0.70V < E < - 0.89V (vs. Hg/HgO). A second process at more negative reduction potentials involves reduction of TeO3 2-, Pb2+ and Tl+ to PbTl4Te3 in a potential interval of -1.02V < E < - 1.19V. The crystalline Tl2Te3 and PbTl2Te3 were deposited electrochemically on Ag substrates at -0.84V and -1.10V respectively. Thermoelectric (TE) material can form a temperature gradient across the material to make electric voltage, which is popular in waste heat utilization and recovery industry. Lead telluride, PbTe, is a small band gap semiconductor of 0.32eV at 300K. PbTe can change its n-type semiconductors with Pb-rich to p-type semiconductors with Te-rich[1]. And it is one of the best TE materials used in thermoelectric generators working between 500K and 600K, or even at a higher temperature of 800K.Three facto,rs play a role in the performance of a thermoelectric material: electrical conductivity (s), thermal conductivity(?), and the Seebeck coefficient (S). These can be combined with absolute temperature (T) to give a figure of merit (ZT) for the material, ZT = s2sT/?. By increasing the electrical conductivity and decreasing the thermal conductivity, which can enhance the ZT value, many efforts, such as alloying with other elements and making the materials nano-sized, have been done to improve its properties recently. Hsu et al. reported that the ZT value of Cubic AgPbmSbTe2+m is increased to 2.2 by doping Ag-Sb to PbTe.[2]."

Jan 1, 2011

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Singareddy R. Reddy, Ramana G. Reddy

"The Margules equation is used for interpreting excess Gibbs energy of several ternary systems. An expression for the activity coefficient of a dilute solute, 2(oxygen), in a binary solvent 1-3 is derived. It is used to calculate the logarithmic activity coefficient of oxygen in Pb-O-Gu, Pb-O-Bi, AgO- Sn, Pb-O-Sn and Ag-O-Pb metallic systems. Self interaction parameter of the solute is derived from the partial Gibbs energy of solute using constant compositional path. The derived equation is used successfully to deduce the self interaction parameter of oxygen in Pb-O-Gu and Pb-O-Bi metallic systems. The predicted thermodynamic parameter data i.e activity coefficient and self-interaction parameters are in an excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.1 IntroductionThe nature of solute interactions such as oxygen, nitrogen and sulfur with the metallic solutions are important for a number of chemical and metallurgical processes. Several theories [1-23] have been developed to evaluate fundamental thermodynamic properties of solutes constituting two elements. The activity of solutes has been calculated using statisticalor quasi- chemical approach.Wagner's [4] Ideal Solvent Model is based on one energy parameter to describe the compositional dependencies of the activity coefficient of nonmetallic solutes such as oxygen in binary metallic solutions. This model depends on a constant energy of interaction for the exchange of atoms from the coordination shell of an oxygen atom to the shell of an interstitial site and cannot account for properties of strongly interacting systems [4]. Therefore, several attempts have been made to improve the Wagner's model for the strongly interacting systems. [10-16]."

Jan 1, 1996

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of&apos; ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By Mukesh K. Agarwala

Alloy composite parts were made from powders by Selective Laser Sintering (SLS). SLS is a rapid prototyping process that uses data from CADICAMICAE systems to guide a laser beam and rapidly form 3-D prototype parts from powders without any part specific tooling. In this study, Bronze-Nickel parts made by SLS were studied for their mechanical properties. To make the parts structurally sound, SLS parts were further processed by conventional isothermal sintering, without loss of shape. The resultant densification and mechanical properties were studied and related to microstructures and P/M densification models. These results were then correlated to the SLS processing parameters.

Jan 1, 1994

By Jewel Gomes

Produced water (PW) is salty water trapped in the reservoir rock and brought up along with oil or gas during production. It subsists under high pressures and temperatures, and usually contains hydrocarbons and metals. Therefore, it must be treated before being discharged to surface water. Different techniques are being used to treat PW through phase separations, system control and design, and chemical treatments. In this paper, we discuss our experimental results on treating PW through electrocoagulation (EC). The performance of EC was investigated for the reduction of chemical oxygen demand (COD) and metal ions. Effects of different electrodes, residence time, current density, and pH were also studied to optimize the treatment conditions. Different kinds of cleansing agents, such as lime and borax were used to break the buffering effect encountered during treatment. FTIR, SEM/EDS, and XRD were used to characterize the EC-floc and thus to elucidate removal mechanisms.

Jan 1, 2009

By Sheng-li Wu, Guo-liang Zhang, Bo Su

One of the major challenges for the Canadian Gen IV Super-Critical Water-cooled Reactor (SCWR) concept is the selection of fuel cladding materials. The Canadian SCWR concept will operate at a core outlet temperature of 625 oC and 25 MPa of pressure with peak cladding temperature reaching as high as 800 oC. Corrosion resistance is an important factor for material selection. Austenitic stainless steels that contain Cr contents greater than 18 wt.% are generally considered to provide adequate corrosion resistance. In this work, the pressure dependence of the corrosion of austenitic stainless steel 310 containing 24 wt% Cr is assessed at 625 C for exposures of 1000 hours to evaluate the suitability of superheated steam as a surrogate for supercritical water at 25 MPa. Transmission Electron Microscopy (TEM) revealed that 310 exposed to different pressure conditions at 625 oC. (i.e., 0.1, 8 and 29 MPa) had generally the same type of the oxide structure, i.e., a Cr-rich oxide with the spinel structure on outer surface adjacent to the water phase. The material exposed at 8 and 29 MPa had a double layer oxide structure, with the outer oxide layer having a much larger grain size, while the samples exposed at 0.1 MPa showed only a single spinel-phase oxide layer. Cr-depleted recrystallized austenite grains were found underneath the spinel phase oxide. The adjacent large-grained austenite substrate had M23C6 carbides in the grain interior. The implications of these results are discussed.

Jan 1, 2015

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Zhigeng Xu

Pressure leach of a Yunnan marmatite concentrates with adding coal as the elemental sulfur disperser was investigated. The experimental results show that the coal with carbon content higher than 70% is incapable of dispersing elemental sulfur from minerals and cannot improve the leaching of zinc. The coal with low carbon content (lignite coal) can act as excellent sulfur-disperser in the pressure leaching at 423K. The mechanism of lignite coal as sulfur disperser was further discussed by ultraviolet, infra-red spectrum and mass spectrum.

Jan 1, 2008