Search Documents

By James G. Donovan, Mario G. Karfakis

A large percentage of Southern Appalachian coal reserves are located in seams less than 36" thick. As thicker and currently more mineable deposits are exhausted, methods of underground thin-seam extraction must be developed. Past experience with highwall mining of thin-seam coal has indicated that recovery rates tend to be lower than in conventional operations. It is suspected that this will also apply to underground thin-seam mining, regardless of proposed technology or mining method. Backfilling is one alternative for thin-seam coal mining; although backfill has been used extensively in hard rock mining its use in coal mining has been limited. The ability of backfill to provide additional ground support may enhance coal recovery by allowing for the design of undersized pillars. Backfill is capable of providing additional ground support by restricting lateral deformation of surrounding coal pillars and roof. This additional support can result in significant increases in recovery from thin-seam coal deposits. However, the overall feasibility of backfill is dependent on the in situ behavior of the fill material, the properties of the fill, the effects of the filling method on the total mining operation, and the cost of filling per extra ton of coal recovered.

Jan 1, 2001

By R. L. Grayson

The Office for Mine Safety and Health Research, National Institute for Occupational Safety and Health is responsible for providing research leadership in the prevention of mining work-related illness, injury and death. Planning of the NIOSH FY99 research program focused on the comprehensive collection and risk analysis of fatality, injury and illness data according to commodity and mine type. This data, coupled with the mapping of information obtained from stakeholder meetings over several years, provided the basis for prioritizing research needs. Results of the combined analysis were compared to the FY98 program to identify surveillance and research gap areas. The FY98 research program was then assessed according to commodity and mine type and compared with exposure assessments, traumatic fatality rates, injury rates and employment trends in each commodity-mine type combination to gain insight into the potential balance of the future research program. This paper presents the methods, data and results of this planning process.

Jan 1, 2002

By Phil Allen

A synthetic fiber manufactured by one chemical company has been treated by another chemical company to produce a cloth fabric capable of performing ion-exchange functions. Only a few delimiting parameters have been established. This paper will discuss briefly the highlights of a functioning ion-exchange cloth. Throughout the paper this fabric will be referred to as "Fabric Z".

Jan 1, 1970

By S. C. Suboleski, J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later it will semiautomate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide the section foreman with real-time or near-real-time information about the performance of the loading and hauling units. This data will allow the section foreman to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and in-mine testing results from the first phase are now available.

Jan 1, 1994

By Robert G. Woolery

Union Carbide_ began looking seriously at heap leaching in 1971. At that time some 1.6 million tons of mineral averaging 0.040% U308 were stockpiled at various sites around the Gas Hills, Wyoming, uranium facility. Several alternatives for economically exploiting these reserves were considered and heap leaching seemed the most attractive. At the time, Western Nuclear Inc. was operating a heap leach project nearby in which the low-grade ore was leached with sulfuric acid, the product liquor treated in an on-site solvent extraction circuit, and the stripped product liquor re-acidified and recycled. They were most generous in allowing us to visit their site, answering our questions, and were helpful in discussing the problems associated with heap leaching. They confirmed our belief that, it was possible to operate a heap leach profitably on material too low grade for. conventional milling. Based largely on what we had learned from Western Nuclear's experience, a program was set up involving a laboratory study to determine the characteristics of the mineral stockpiles as related to heap leaching and to conduct a pilot heap leach adjoining our Gas Hills mill. Basically, the pilot heap construction and leach procedure were similar to those described in the literature(1,2) with certain modifications to permit detailed monitoring of the operation. In May, '1972, the decision was made to construct a test heap. The UCC plant at Gas Hills, Wyoming was selected as the most appropriate site for the follow¬ing reasons:

Jan 1, 1977

By Eric Monrad

Discrete event simulation modeling provides a tool to quantify the throughput capacity of stockyards. Interactions between the main equipment types (trains, dumpers, conveyors, stackers, reclaimers, shiploaders) can be captured, including route blockages, breakdowns, and planned maintenance. Simulation has been successfully used at world-class stockyard facilities to determine current capacity and to identify gains resulting from improvement projects. Recent projects have focused on iron-ore, coal, and soya facilities, but the technology is suitable to be used on any bulk material type.

Jan 1, 2008

By Richard C. Fountain

The Central Florida Phosphate District is located in southwestern Polk, southeastern Hillsborough, Manatee, and Hardee Counties, Florida, flanking the.southern end of a major structural uplift known a the Ocala arch. Ore control problems here are varied and unique due to non-homogeneity of matrix and high volume mining operations. Overburden stripping and matrix mining are performed by large draglines, the matrix being slurrified and transported to the processing plants hydraulically. Production geologists' responsibilities include, 1) prediction of special mining problems, 2) prediction of ore quality and quantity, and 3) the physical control of the ore quality and recovery during mining. prediction is based on core drilling and visual inspection and analysis of the core samples. Basic economic, and physical minability criteria are thus established. Ore grade and tonnage recovery are of particular importance with emphasis being placed on coordination between mining and processing personnel. Routine inspection of the working pit face is of prime importance and both physical and quality variations are pointed out to the mining supervision. Physical problems in ore control occur due to erratic clay, dolomitic limestone and sand lenses. Near surface ground water is abundant, posing a threat to recovery. Contaminants of the phosphate ore are large quartz grains, pebbles of cemented quartz sand, clay balls, iron oxide laminac and dolomitic limestone particles. Success of the ore control program is predicated on a balance between predicted ore tonnages and grade and actual production. The geologists' primary attention is directed toward this balance.

Jan 1, 1972

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By J. A. Dille, J. P. Hand, J. D. Brown

The purpose of this paper is to inform members of the coal producing and consuming community about techniques used by The Carter Mining Co. to control product quality at a large surface coal mining operation. During the early years of mining operations, coal quality received adequate attention but the company's main emphasis was to build up its production rate and minimize mining costs. While these goals are still of prime importance, coal quality has received additional attention in recent years. An objective that no coal shipment should exceed any contract or company-imposed coal quality specification has been successfully met. To implement this guideline, geology and coal quality modeling procedures were improved, in-pit drilling and blending programs were refined, and detailed shipment procedures were developed.

Jan 1, 1987

By Byron N. Cooper

The Revenue Act of 1926 provided for five simple categories of natural resources to have the benefit of depletion allowances. In the 1947 Revenue Act, the number was increased to twenty-five, and in the 1951 Revenue Act to fifty-four. Of this number, fourteen were allowed 5 per cent; nine, 10 per cent; twenty-nine, 15 per cent; one, 23 per cent; and one (oil and gas), 27.5 per cent. The 1951 Revenue Act created a host of difficulties, including application of the "end- use criterion" and determination of the commonly accepted meaning of such terms as limestone, dolomite, chemical- and metallurgical-grade limestone, marble, calcium carbonates, and magnesium carbonates. Dolomite, for example, was listed at 10 per cent depletion allowance, but without definition. In the great amount of litigation growing out of the 1951 Revenue Act and its administration, it became essential to understand the derivation and subsequent usage of these common geologic terms. One thing that became clear was that our definitions changed significantly between the time that the 1951 Revenue Act became law and the time that later cases were tried. Some geologists neglected to learn about first usages of such terms as metallurgical limestone, and about meanings that were applicable when the 1951 Revenue Act was written and passed. Legal meanings in this paper are discussed in the light of certain famous cases that have been tried and settled.

Jan 1, 1966

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By R. L. Eppley

The Blacklick Creek Watershed Association was awarded a $158,000 Growing Greener grant from the Pennsylvania Department of Environmental Protection in 2002 for the design and construction of a sulfate reducing bioreactor (SRBR) cell to treat acidic discharge from the Judy 14 abandoned underground coal mine near Indiana, PA. The vertical flow SRBR was designed to treat 38 liters per minute of MIW containing elevated concentrations of aluminum and iron. Other treatment systems at this site plugged due to aluminum precipitates; this problem did not occur in the SRBR. The bioreactor has been periodically overloaded with flows up to six times the design rate. To date, the only maintenance performed on the unit has been the addition of hay to the surface of the unit in response to less than expected performance. The periodic hay additions appear to have restored the SRBR to nearly post-construction levels. Since construction, the SRBR has treated about 136,000 cubic meters (36 million US gallons) of MIW.

Jan 1, 2010

By D. R. Buist

The Taharoa plant of New Zealand Steel Mining Limited extracts a 57% Fe titano-magnetite concentrate from a large mineral sand deposit 90 miles south of Auckland on the west coast of New Zealand's North Island. The plant consists of an 18-inch suction cutter dredge which feeds a 750 TPH floating separation plant. An initial gravity/ size separation is obtained using cone concentrators. Finished concentrate is produced by a combination of conventional drum magnetic separators and top fed wet Mortsell magnetic separators. Concentrate is stockpiled by cyclone, and reclaimed by a bull- dozer and tunnel system. Repulped concentrate is pumped by sub- marine pipeline to slurry tankers anchored at a single buoy one mile offshore. Current concentrate production rate is in excess of one million metric tons per year.

Jan 1, 1973

By G. S. Adisoma, J. J. K. Daemen, R. O. Roko

A common assumption in determining the shear strength of a rock joint using a direct shear test is that the surfaces undergoing relative shear are in complete contact. Furthermore, the limiting displacement associated with the residual strength values is obtained based on engineering judgement through visual inspection of shear force versus displacement curves. This study proposes a systematic way of determining the residual shear strength of rock joints by evaluating the limiting displacement leading to a minimum cohesive strength value and taking the true area of contact into account. The results of the study indicate that there is a limiting displacement associated with the residual shear strength, and some rocks may have an inherent interface residual cohesive strength different from zero. When the cohesion is different from zero, the residual shear strength is likely to be underestimated if the true area of contact is not considered. In the case where zero calculated cohesion is obtained, the area of contact has no bearing on the shear strength equation because the frictional force depends only on the normal load.

Jan 1, 1986

By Kenneth N. Han, Jianshe Liu

Various techniques used in the removal of metal ions from effluent streams have been reviewed. These techniques include recovery of metals by biological treatment, chelating agents, adsorption, ion- exchange and chemical precipitation. The main thrust of this paper however, is concerned with the removal of cadmium and zinc ions from the solution by adsorption utilizing liquid fluidized beds. The bed particles used were silica of 150x200 mesh. The range of the concentration of these ions studied was 10-3 to 10-5 M. Important variables examined included flow rate, concentration of metal ions and amount of bed particles. A mathematical model describing the concentration profile of metal ions in the axial direction in liquid fluidized beds has been developed. The equation of continuity was solved numerically and the results were used to predict the recovery of metal ions in fluidized beds.

Jan 1, 1992

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Ryan Lindmark, Guoxing Gu, Zhenghe Xu, Jacob H. Masllyah

Induction time is often referred to the time required to form a stable three-phase contact between a gas bubble and a flat or droplet surface in a liquid medium. It can be used to quantify the attachment process in aflotation system. Various techniques have been developed to measure this important parameter. Due to its importance in flotation systems and other processes, significant advances in refining the induction time measurement techniques have recently been made. This paper summarizes these recent advances and describes a novel method developed to monitor bubble attachment to a pendant bitumen drop or bitumen-coated flat surface. This visualization-based method offers a higher sensitivity and accuracy than the previously developed apparatuses in the induction time measurement. As an example, the induction time for oxygen bubble-bitumen attachment was measured at a fixed bubble size as a function of temperature in two different aqueous solutions. The results showed that higher process temperature is favorable for oxygen bubble-bitumen attachment and hence bitumen flotation. Addition of calcium to the aqueous solution slightly decreased induction time.

Jan 1, 2005

By -Ing. Alexander Dohmen, -Ing. Gunter Hagen

In order to improve the thermal environment in deep coal mines, two principles can be applied: firstly, the reduction of heat flow into the air stream, and secondly, cooling of the air current. First of all one should try to minimize the heat-flow rate into the air stream underground by the mining method itself. German coal mines prefer the caving system of advance longwall mining simultaneously on several levels with ascensional ventilation. The effects of descensional ventilation and different face ventilation layouts on the thermal environment are discussed, besides the effects of pneumatic and hydraulic stowing. Application of all mentioned possibilities together instead of today's common mining method would reduce the Basis Effective Temperature considerably. In the future, hydraulic haulage of the raw coal underground substituting belt conveying may be a mean to improve the thermal environment further on. If the working depth of a coal mine exceeds about 1 000 m, cooling of the air stream under-ground will be necessary in addition to the above- mentioned measures. Generally, in German coal mines different types of indirect-contact air coolers located nearby the face are used. Besides such so-called cooling coils, large-capacity spray coolers are used because they work more efficiently if a great cooling duty is demanded. Common designs of both air cooler types and their possible utilizations are demonstrated. Deep coal mines in the Federal Republic of Germany need up to 30 MW of total cooling capacity. Mostly, the needed chilled water is cooled by large-capacity refrigeration plants placed on surface, underground or in combination of the above locations nearby the shaft. Due to the increasing underground cooling demand, the distribution of the chilled water and the control of the air coolers become more important. The conception of a control system is discussed, which is based on the control of the single air coolers. All air coolers of a mine are controlled so as to optimize the supply water-flow rate with regard to the demanded cooling duty of the coolers. On the next upper level of the control system the whole chilled water network and finally the refrigeration plant is regulated. Present research work deals with the use of ice for cooling mines. There are some unsolved problems in this new cooling concept. Some aspects of making, transporting and storing ice are described. The use of ice may probably reduce the cooling costs of German collieries, which are at present approximately 4 DM per ton of saleable coal.

Jan 1, 1989