Search Documents

By John J. Friel

The addition of dolomite to iron ore pellets improves their high-temperature reduction properties primarily by increasing their reducibility and raising their softening temperature. In this study we prepared dolomite-fluxed pellets from three different concentrates; Hibbing, a magnetic taconite, Knob Lake, an earthy hematite; and Carol Lake, a mixture of specular hematite with magnetite. The composition n of the concentrates is given in Table I. The pellets were subjected to standard physical tests and the following reduction tests: low temperature degradation, swelling, softening, and thermogravimetric analysis. Petrographic examination and electron microprobe analysis allowed us to evaluate the effect of composition and firing on the phase assemblage. Further, we were able to interpret the test results in terms of chemistry and microstructure. This approach enabled us to determine which fluxed composition best suited each of the concentrates.

Jan 1, 1980

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By Syd S. Peng

The key design parameters of roof bolting using expansion - shell type support for underground coal mine roof support are bolt length, bolt spacing, installed load and anchorage capacity. Depending on the utilization of suspension effect or friction effect, the bolt length is dictated either by the distance between the roof surface and the first overlying strong strata encountered or the desired magnitude of reduction in bending stress at the roof surface, The current prevailing practices about the bolt spacing and installed load are that an initial torque of 125 - 170 ft-lbs is applied and the bolts are spaced at 4- or 5- ft. square grid pattern. This seems to be a rather broad generalization in view of the great geological variances which are expected in underground coal mines. A modest evaluation program to measure the effectiveness of current roof bolting practices is to monitor the load history of roof bolts during a complete mining cycle including the phases of room development and pillar robbing. The load history, when compared with the anchorage capacity of roof bolts determined by in-situ pull tests, will provide information for evaluating the installed load, the bolt spacing as well as the specifications for structural and anchorage characteristics of the bolt assemblies. This paper presents a case history of monitoring the complete load histories of roof bolts in an underground coal mine of Pittsburgh seam.

Jan 1, 1976

By P. Zhu

The leaching behavior of copper powders recovered from waste printed circuit boards (WPCBs) was investigated using electrogenerated chlorine and aeration in a sulfuric acid solution with added NaCl and CuSO4. Various parameters were studied to understand the mechanism of the copper leaching. When the current density increased from 0 to 0.1 A/cm2, the temperature from 30 to 60° C, agitation speed from 100 to 400 rpm, and the size ranged from below 75 to 150 µm, the leaching ratios of copper powders increased. The leaching kinetics were analyzed using a shrinking core model: 1-(1-X)1/3 = kt, and the leaching process was chemically controlled with an activation energy of 14.7 kJ/mol due to Cl- ion catalysis. The ratios of [Cu+]/[Cu2+] at various temperatures (30, 40, 50, 60 and 70° C) showed a periodic variation with the increasing of the leaching time. The redox potentials of the leaching solution and copper leaching ratios in different conditions were measured. The result indicates that dissolved oxygen achieved the dissolution of coppers and electrogenerated chlorine can promote the dissolution of copper powders and improve the reaction rate of kinetics in the presence of oxygen.

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp., and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the seconaary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1981

By Christine E. Turner-Peterson

Pore-filling organic material concentrated uranium to form sandstone-hosted primary uranium deposits in the Jurassic Morrison Formation of the Grants uranium region, New Mexico. Petrographic observations and radiometric ages for primary ore in the Westwater Canyon Member require that the organic material was emplaced early in the diagenetic history of the host sandstone; in fact, organic material was emplaced before major compaction. This inferred early emplacement constrains models concerning the nature and origin of the organic material and thus also constrains models of ore genesis. Reconstruction of the burial history of the basin indicates that Late Jurassic-Early Cretaceous time, the interval of inferred emplacement of the organic material, was probably not a time of hydrocarbon generation and migration. Nuclear magnetic resonance analyses, elemental abundances, and isotopic studies provide further constraints on the nature of the organic material, and data from these studies are consistent with a humic acid rather than an oil origin. In addition, the overall tabular shape of primary uranium orebodies and the way these orebodies are suspended in the host sandstone mimics Recent deposits of humate, the precipitated form of humic acids. The critical clue that favors a humic acid origin for ore-related organic material is provided by the nature and patterns of postdepositional alterations that are spatially and temporally related to primary ore, specifically destruction of detrital magnetite and ilmenite (iron-titanium oxide) grains. Humic acids are implicated in the destruction of iron-titanium oxide grains because these organic acids are one of the most effective natural agents in leaching of Iron from these grains. Thus, timing constraints, chemical evidence, orebody geometry, and the nature and patterns of ore-related alterations favor a humic acid origin and suggest that an oil origin is highly unlikely. Because alteration of iron-titanium oxide grains tracks the pathways of humic-bearing solutions through the host sandstones, it is possible to trace these solutions back to their source. Alteration patterns in the Westwater Canyon Member suggest that the humic-bearing solutions originated as pore fluids in the mudflat facies of the overlying Brushy Basin Member and moved into adjacent sandstones during early dewatering of the mudstones. The humic acids precipitated, by the process of cation loading, in tabular layers. Uranium was concentrated within these tabular layers by complexation with the humic acids to form primary uranium orebodies.

Jan 1, 2013

By H. Nakazawa

Galvanic contact, occurring between electricall y conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions, and the results were correlated with their oxygen-consuming characteristics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, x-ray photoelectron spectroscopy and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased whereas that on pyrite increased when these minerals were held in contact. An electrochemical mechanism was proposed for the observed behaviors.

Jan 1, 1985

Power consumption of stirred media mills has been studied by an approach developed from work on stirred reactors. Relationships between torque required to rotate both disc and pin impellers immersed in dense particulate media as a function of speed, impeller and tank dimensions, and other relevant variables are evaluated. Data collected during numerous different experimental conditions are analyzed. The results can be summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention is directed towards the rheological properties of the media, which is considered as non-Newtonian liquids and hence, the equation of power law liquids is employed. Procedure for estimating parameters of effective viscosity and scale-up guidelines with respect to power consumption are put forward.

Jan 1, 1994

By Wendell H. Nielson

Flotation processes contain disturbances which make material balance closures difficult to achieve. Lack of closure also arises from instrument errors. A portion of these problems can be overcome by proper equipment selection; the primary measurement installation and methods of initial data filtering are discussed below. The problem of data adjustment has been considered before (2). The technique described here is essentially that of Ripps (2). The technique was expanded to include linearization of non-linear material balance equations. An additional large error detection portion was also added to Ripp's formulation. Ripp's technique is based on a Lagrange-Multiplier optimization method. The Lagrange-Multiplier technique is generally applied when there are equality constraints on the variables. Steady-state material balance equations fit in this category. The basic Lagrange-Multiplier method is described. It is followed by a description of the modified material balance data adjustment technique. An example is presented to illustrate the use of this method.

Jan 1, 1970

By Tadashi Nishida

Subsidence due to mining caused various kinds of damage to the surface structures, and actually great deal of mining damage becomes the severe social problem at some time in many coal fields, but the most of mining damage was restored at present. Recently, the effect of old coal working on the deformation of newly constructed structures has become into question, because it was obliged to plan many engineering structures in old mining areas for the shortage of adequate construction sites and the difficulty of getting location. That is, building, dams, bridges for railroads and highway, power plants, tunnels, storage tanks and so, have to be built on the ground which has old coal working.

Jan 1, 1982

By Ronald Ludchak

Since coal has been designated as the short-term answer to the threatening world energy crisis, improved surface mining techniques, along with improved extraction and handling equipment, are needed to increase the amounts that can economically be mined by open pit methods. A dwindling supply of low cost oil and gas have dictated a major rethinking of our energy sources and their use. New methods for open pit coal mining have to be found to increase coal production and to meet more stringent reclamation laws. Modern twin-engine elevating scrapers can play a vital role in meeting these needs. They are readily available, with short delivery times, from several experienced manufacturers of earthmoving equipment. Recent developments of the elevator system have extended its working range to include many of the materials commonly encountered in open pit mining. The paper deals with the advantages of using twin-engine elevating scrapers in the performance of various mining tasks. These tasks range from utility work to the major task of using the scrapers as a primary stripping toot and, of even more importance, a stripping- reclamation tool for, with scrapers, the overburden can be moved and redeposited in the same strata sequence or soil horizon as in its natural state. A recap of current applications of the elevating scraper will be presented, along with proposed uses.

Jan 1, 1975

By Paul Basinski

The Northern Reese River Valley is in west-central Lander County approximately 31 miles north of Austin, Nevada in the north-central Basin and Range Province (Figure 1). Authigenic zeolites, which were previously undescribed in the literature, are voluminous in this small sedimentary basin. Uranium mineralization is also abundant in this study area. Until now, what we believe to be cause and effect have not been put together. X-ray diffraction, differential thermal analysis, and scanning electron microscopy reveal clinoptilolite, erionite, analcime, and minor chabazite to be present (Figures 2, 3). Assays show uranium to be present in thicknesses up to 0.7 meters at amounts up to 0.10% eU308. The sediments in the Northern Reese River Valley belong to the Mio-Pliocene Humboldt Formation equivalents. This formation consists largely of tuffacious lacustrine and fluviatile sedimentary rocks. Mudstone is the dominant lithology and intercalated thin zeolite strata (usually less than 0.6 meter thick) are present. Zeolites in the Northern Reese River Valley were diagenetically derived from rhyolitic glass deposited in a shallow, saline-alkaline lake under arid to semi-arid conditions. Clinoptilolite from the study area was K-Ar dated at approximately 4.7 + 0.5 million years which corresponds to Middle Pliocene age (Krueger and Basinski, in press). This age is further substantiated by Middle Pliocene mammalian fauna collected in the vicinity by Deffeyes (1).

Jan 1, 1979

By James Yancik

The Howe Coal Company located in Leflore County, Oklahoma is mining the Oklahoma Lower Hartshorne Coal bed which ranges in thickness from 38" to 42" and dips approximately 7 degrees to the Northeast. The Lower Hartshorne bed lies within the Hartshorne sandstone in Oklahoma but is as much as 60 feet above this sandstone formation in Arkansas. This coal bed extends throughout the Arkansas Oklahoma coal basin, which is about 50 miles wide and 180 miles long and progresses from a semi anthracite in Arkansas to a low-volatile coal in the eastern part of the Oklahoma to a high-volatile coal in the western area. The Howe Mine #1 in the eastern area is mining a low-volatile bituminous coal which has been used as metallurgical coal since the early 1900's as evidence of Bee-hive coke ovens still remain near the town Howe, a few miles northwest of the mine site. The Howe Mine is the first mine in the area to use modern mining equipment, however, numerous punch mines have been worked along the outcrop south of the mine site dating from 1900 with the last closing in 1965. The coal characteristics of the Lower Hartshorne rival the Pocahontas seam in chemistry and coking qualities. This paper will be concerned with the preparation of the coal for the Japanese steel market. The three man crew necessary to operate the plant are the operator, the helper, and the equipment operator needed to feed the raw coal hopper. An additional equipment operator is available on the day shift for coal loading and moving the clean coal to the storage pile as the area under the clean coal belt is only large enough for 1 shifts production. We are at present running the plant on a 2 shift per day basis.

Jan 1, 1969

By Günter Strappler, Max John

When tunneling through karstic terrain, diverse and complex karst structures are to be expected. By means of drilling ahead of the face using drill jumbos, these structures can be detected to such a degree that by applying proper support measures both open karst cavities and karst holes surrounded by boulders embedded in soft rock can be mastered without causing any break-outs. Support measures such as spiles ahead of excavation, sealing off cavities, back?lling with sand, etc. have to be planned schematically and adapted to the dimensions and formations of the karst structures on site. An essential requirement for a smooth excavation procedure is the availablility of all necessary tunneling equipment for excavation by drill and blast as well as for excavation of soil, with experienced tunnel engineers being in charge of any adaptions on site.

Jan 1, 2003

By Dean E. Albon

In the late 1940's and early 50's in southern Illinois, the usual open pit blasting in the coal field consisted of one or two rows of churn drilled vertical holes being shot with instant electric blasting caps. The entire shot detonated at one rime. In southern Indiana and Ohio most mines were drilling horizontal holes and they too were primed with instant EB caps. During the ten years from 1355 through 1965 many changes occurred in drilling and blasting methods. The churn drill in southern Illinois and the horizontal drill in Indiana and Ohio were replaced by the rotary vertical drill. The ammonia dynamites and liquid oxygen explosives were replaced by ANFO. The elctric blasting cap in the hole was replaced by a detonating cord down line and detonating cord trunk lines made the connections between holes and rows of holes. Host open pit mining was in areas far enough from town that the noise and vibration from blasting was, if not ignored, at least tolerated. During the 1960's open pit mining expanded to account for nearly 50% of the coal produced. Mines came closer to town and towns expanded along the highways with suburban homes and mobile homes. The mines began receiving complaints about the noise and vibrations from blasting operations.

Jan 1, 1976

By Kadri Dagdelen

The classification of selective mining units (SMU) and the assignment of grades to those classified SMU are very important in open pit mining, especially for precious metal mining. When the classification is done, the true values of the SMU grades are unknown. These unknown SMU grades are mostly estimated analyzing the geologic data and blast hole assays. To classify the SMU's based on the estimate of SMU grade, without considering uncertainty associated with unknown SMU grade, yields incorrect decision in sending material to appropriate destination. In this paper, a method is developed to classify SMU's considering the uncertainty associated with unknown SMU grades. By using this method, traditional estimate of SMU grade is replaced with conditional probability distribution of SMU grade. The decisions about the destination of a given SMU are performed by minimizing the loss due to misclassification. Also, the asymmetric loss function by penalizing the overestimation and the underestimation unequally is used in assigning grades to classified SMU's. A case study is carried out to apply the traditional ore control techniques and proposed method in classification of SMU's and the assignment of the grades in a hypothetical gold mine.

Jan 1, 1999

By Bruce H. Mason

The exploration for a commercially acceptable deposit of limestone is consid¬ered by many to be a relatively easy task; however, trying to locate a zone of high calcium limestone of economic thickness within a formation, which outcrops only in a narrow band varying in width from a quarter mile to ten miles, adds considerably to the normal problems experienced during an exploration program. The existence of varying glacial and karst features in the outcrop area intensified the problems encountered and complicated the interpretation of the economic value of the deposit. This paper highlights a recently completed five year exploration program during which approximately 3,900 acres of ground in seven civil townships were evaluated as potential sources of high-calcium limestone. Details are given with respect to the final site chosen and the methods used in determining the suitability of the site. This site exhibited many karat features and several methods were utilized to determine the effect of these features on the gross characteristics of the deposit. Aerial photography for both mapping and interpretation were utilized. Black and white panchromatic photography, black and white infrared and color infrared photography were flown. Resistivity, diamond core drilling and close-interval angering were used to supplement the information obtained from the aerial photography.

Jan 1, 1974

By D. W. McGlashan

[Becaune ad ;the extennive nwrgace anea od u.X chopRex2 in emmiom, emuhion dRokdtiun oddeh poaaibWa don ;the necove/ry ul; BinQey divided minmcd pa~LL&a, Swr~aC;tavu% mu2 akab&ze ;the emu-bion and poan an an ad~i&y don ;the dahed mina&. OZhm hpohtant acto oh me ;the naAwre od ;the em&iun inghedied, ;the nQRaLLve volwna 06 the colz;tinuoun and dincon;tinuoun phaa, ;the change aign bonne by the dnuplm ad the o.X phae, ;the z&a pu;tenticd od ;the dahed minmd, the ~olubRe am curdent 06 khe wcr;ten-pulped and gnuund onu. AX on nem ;the AoQRec;trtic point on ZPC, ;the doubRe Raym about ;the minW-&den oil dnopR& i~ neduced in ;tkichnaa and the dn_opR& wU codace and continue to aggnegate into agglommaka . Invetmion dnom O/U ko W/O can UCCWL depending upon a nwnbm a 6 in;tmQeaked daotuh~. EReothokin&Lc inn&wnenta;t/iun to meanwre ;the ZPC, QReckProphonQkic mobilXty z&a pokeW and hakerning cuttrtent me invcduabte in ;the appficatiun ud emu-bion dRo;tat;iun ;to m&~c and nonm&~c minu.&. ] INTRODUCTION Recent interest in emulsion flotation can be ascribed to the necessity of selective separation and concentration of extremely fine minerals. That which follows is an elucidation of the many factors-in emulsion technology in application. In applied surface chemistry for solid-particulate separation and concentration, emulsion flotation is one of the intermediate processes between froth flotation, in which the continuous phase is water (99.5 to 99.999% by volume), and particulate extraction, in which the continuous phase is almost entirely an organic-fluid. Another intermediate process is particulate exchange (or partition) in which immiscible or very limitedly miscible phases are in controll¬ed but appreciable volumes. Surfactants are common to all of these

Jan 1, 1968

By Charles B. Escapule

The first successful heap leach of silver ores in the State of Arizona has been under continuous operation since early 1976 at the State of Maine Mine, two miles southwest of Tombstone, Arizona. The silver produced from leaching old mine dumps at this property vas the first in the Tombstone mining district to achieve a 999+ purity. While cyanide leaching of silver and gold ores is a time-proven accepted practice, a relatively new method of treatment called "heap" leaching was employed. Heap leaching is a comparatively inexpensive fast way to recover precious metals from low grade material.

Jan 1, 1981

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985