Search Documents

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Feb 24, 1997

Komatsu America International has introduced two new hydraulic excavators. They can work in congested and confined areas. The tight tail swing radius of the PC128US-2 and PC22-8USLC-2 enables the excavators to minimize the work space. The units can operate in confined work settings that are inaccessible or counterproductive to traditional machines. Even the door is designed for tight working conditions. A convex door slides open along the exterior curve of the cab, rather than swinging out on hinges past tracks. And the excavators’ tight tail swing design allows them to load within the track width of the machine.

Jan 1, 2000

By M. Baumann

Introduction Gold Quarry is one of the largest gold deposits in Nevada, located along the Carlin Trend, approximately seven miles north of Carlin, NV. Owned and operated by Newmont Mining Corporation, as of December 31, 2005, Gold Quarry had produced over 13 million ounces of gold. Multiple simulations were constructed for gold and metallurgical variables using the Stepwise Conditional Transformation method. Analyses of these simulations have been used for a variety of purposes, including an assessment of uncertainty with various ore types. This assessment provides insight for improved modeling and reconciliation. Geological Framework Gold Quarry is a large, low-grade disseminated gold deposit hosted in Silurian-Devonian aged sediments at the Chukar/Alunite-Good Hope fault intersection. Gold bearing hydrothermal fluids appear to have migrated upwards along the Chukar/Alunite and Deep Sulfide Feeder faults and then moved outward along favorable stratigraphic horizons and structural intersections.

Jan 1, 2007

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

By Marco Sonnenschein

As time is costly, engineering companies have developed methods, procedures and mechanical equipment to tunnel faster. But the best excavation method will not be able to cope with the time pressure if there is not a reliable backup system. Therefore, the application of belt conveyors for tunnel boring machine (TBM) drives as well as for drill-and-blast driven tunnels assure a quick and smooth removal of excavated soil in order to enhance the efficiency of the tunneling equipment. During the last 10 years, belt conveyor systems have achieved ?state-of-the-art? levels and have become the first choice for muck removal systems in both TBM and drill-and-blast driven tunnels. Because time has become such a key criterion in tunneling projects, it is essential that all equipment is operated so as to derive optimum efficiency and minimize costs. Efficiency also means to think about new tasks for existing technologies.

Jan 1, 2012

By Yao Zhou

Under the United Nations Convention on the Law of the Sea (UNCLOS), the international seabed area (Area) and its resources are the common heritage of humanity (CHH). Patent rights can be incompatible with the CHH doctrine and its underlying principles because patent holders might charge unjustifiably high prices to license patented technology for exploring and exploiting the Area’s resources (creating a "patent holdup" situation), might choose not to license, or might license exclusively when doing so would contravene CHH principles. However, a reasonable patent licensing regime can contribute to sharing the benefits derived from the Area and promote environmental sustainability. Provisions of the UNCLOS that stipulated compulsory technology and financial transfers were removed in the 1994 Agreement relating to the Implementation of Part XI of the UNCLOS but to promote equity and sustainability I propose a voluntary licensing regime modeled on the concept of reasonable and non-discriminatory patent licensing that has been used in other contexts. The International Seabed Authority or another entity will need to coordinate and promote this licensing regime through governance of intellectual property derived from the Area. This proposed approach can better effectuate the CHH doctrine and its underlying principles.

Sep 1, 2014

By Bruno Bussière, Michel Aubertin, Anne-Marie Dagenais, Johanne Cyr

A five steps remediation program was commissioned in 1998 for the acid generating Lorraine mine site, located in the Témiscamingue region, Quebec, Canada. It included, as the main expenditure, a cover with capillary barrier effects (CCBE) used to limit oxygen migration. After construction of the cover, instruments were installed on site to monitor the CCBE performance. Modified oxygen consumption tests were also done to measure the oxygen flux through the cover. Results from water content and suction data, measured from 1999 to 2003, show that the capillary barriers effects are effective and that the water retention layer stays near saturation throughout the years. Oxygen fluxes estimated from monthly water content measures are generally below 10 g/m2/year. Results from modified oxygen consumption tests made on the site give almost similar oxygen fluxes. A two dimension numerical model of the Lorraine mine site was also constructed to verify that mathematical models could predict realistically the in situ conditions on such a large scale site. Numerical results obtained for three years show a good concordance between measured and calculated values. The results obtained form these different evaluation methods for the performance of a CCBE concur and confirm the efficiency of this cover in limiting acid mine generation.

Jan 1, 2005

By Joseph J. Feiler

Historical mining operations in Colorado and other western states have resulted in thousands of remnant mine openings. Many are sources of metals loading and acid water generation in surface and ground waters. It is estimated that more than 965 km (600 miles) of streams in Colorado have been impacted by past mining activities. The Animas River watershed in southwestern Colorado is one of the most heavily affected areas in the state. Abandoned mine features pose significant safety hazards to those who enter them. These hazards can include bad air, unstable rock or falls into open shafts, stopes and winzes. Backcountry skiers and snowmobile enthusiasts are particularly vulnerable to falls into snow covered mine openings.

Jan 1, 2006

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

The National Mining Hall of Fame and Museum (NMHF&M) will induct its the 2014 National Mining Hall of Fame Class on Sept. 13, 2014 during its 27th Annual Induction Banquet and Ceremony at the Westin Hotel in Denver, CO. Representing the domestic and worldwide metal production, education, and health and safety sectors of the industry, this year?s four inductees cover a diverse cross-section of the mining industry. Harry M. Conger III, Günther Franz (Frank) Joklik, Ellen Swallow Richards and Dr. Alfred Weiss will join 223 other mining industry pioneers when they are formally inducted into the National Mining Hall of Fame. They were selected for being visionaries, leaders and ambassadors, both within their own sectors and across the industry at large. Conger was a great role model and strong advocate within Homestake Mining Co. and among his industry peers on behalf of environmentally responsible, safe, profitable and high-performance operations. As chairman and chief executive officer, Conger was instrumental in revitalizing and rebuilding Homestake into an industry leader in technological advances and environmental protection. Through his contributions in exploration, project development and operations management as Kennecott president and chief executive, Joklik did much to strengthen Kennecott as a company and assisted in restoring the competitiveness of the U.S. mining industry. Richards is generally recognized as the founder of ecology. She was the very definition of a pioneer in such diverse fields as chemistry, geology and mineralogy, mining and metallurgy, environmental science, public health, home economics and education. Weiss was a true visionary in using quantitative methods and digital computers to aid mineral exploration, plan and design mines, operate mineral production facilities and integrate the disparate information resources throughout a mining company into a modern management information system. NMHF&M Board of Directors Chairman, Paul C. Jones, said, ?Again this year we are honored to be able to induct an outstanding group of deserving individuals who have made exceptional contributions to the mining industry in the United States. Included are two living inductees who have made significant contributions to management in the industry. One inductee was the first female graduate from the Massachusetts Institute of Technology, its first female faculty member and the first female member of AIME who had an outstanding career as a mineral investigator in the United States. Another inductee was a lifetime innovator in bringing digital technology into common use in our industry. Each of our 2014 inductees made significant and lasting contributions to our industry and are well deserving of becoming a member of the National Mining Hall of Fame.? The Hall of Fame Induction Banquet and Ceremony is a marquee event for the National Mining Hall of Fame and Museum each year. The 27th Annual Induction Ceremony and Banquet will be held at the Westin Hotel in Denver, CO on Saturday, Sept. 13, 2014. For banquet reservations, contact the NMHF&M office at 719-486-1229. More information is available on the NMHF&M website at www.mininghalloffame.org.

By Leon Maday, Dan L. Pecha, Jeremy Johnson, Daniel N. Adams

The Brightwater conveyance system includes 26 km of tunnels, a 130 mgd pump station, 2 km of micro tunnels, and a 2.4 km outfall. The tunnels extend from Woodinville to Puget Sound through varying soils in 1 to 7 bars of hydrostatic pressure and depths to 185 m. The tunnel diameters range from 4 to 6 m and include numerous lining systems. This paper highlights major shaft and tunnel design, including dual cellshafts, multiple pipe configuration tunnels, polymer concrete segments, and the use of a one pass lining designed to convey high pressure effluent.

Jan 1, 2005

By H. D. Brenk

"The German Federation of International Mining and Mineral Resources (FAB) is a federation of German companies that are active in international mining and mining related business. The FAB presents a platform for the exchange of information about the worldwide mining commodities in the dialogue with German and foreign institutions. The expertise of the member companies in mining and related activities is based on a long term operation and consulting experience in Germany and abroad. This forms the basis for the special international competitiveness "Made in Germany". The FAB is particularly engaged in the following topics and tasks and acts as a focal point for: • international project developments with the German mining industry, • sustainable mining, consulting and equipment services, • geological and environmental technologies, • project financing and • intermediation of contracts, project enquiries, professional symposia and events. The FAB acts as a contact- and coordination site for international business partners, organizations and governmental authorities. Together with the federal government the FAB organizes bilateral working group meetings in the commodity and mining sector. Project enquiries are being distributed from the FAB among their member companies."

Jan 1, 2011

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By William Connell

NFPA 502, Standard for Road Tunnels, Bridges and Other Limited Access Highways establishes minimum fire protection and fire life safety requirements for road tunnels, bridges and other roadways where access by emergency responders is physically limited. The 2008 edition of NFPA 502 represents the Technical Committee?s consensus of current best practice for fire protection and life safety requirements for road tunnels, bridges and similarly limited access highways. Research of national and international test programs, design guidelines and regulating standards was per-formed and considered in an effort to establish a singular, comprehensive document representing a recognized base threshold of fire safety in these type facilities. This paper provides an overview of the more significant revisions including the application of fixed fire suppression systems, guidance on tenable environment, protection of structure and dangerous goods transport.

Jan 1, 2008

By S. J. Schatzel

Coal mine longwall face ventilation is an important component of the overall mine ventilation system. Increases in the production rate due to higher capacity mining equipment tend to increase methane emission rates from the coal face, which must be diluted by the face ventilation with a minimal opportunity for assistance from additional control equipment (i.e., surface boreholes). Increases in panel length, in some mines approaching 6,100 m (20,000 ft), and panel width provide additional challenges to face ventilation designs. Face ventilation can also be affected by communication with the methane-laden gob gas reservoir. Except in a two-entry system, belt air cannot be used to ventilate the face in the US, except in limited cases. This relatively recent requirement has further challenged the mining industry in maintaining adequate longwall face ventilation. To assess the effectiveness of current face ventilation practices, a face monitoring study was combined with a tracer gas test on a longwall face. The study was conducted at a US mine operating in a thick, bituminous coal seam with some self-heating tendencies. Multiple gob gas ventholes were located near the face and produced a small portion of ventilation air in their production flow. Initial results show that emission rates on the longwall face showed a very limited increase in methane concentrations from headgate to tailgate despite the occurrence of methane delays during monitoring. Increases in methane concentrations in the tailgate entry in the vicinity of the longwall face T-junction appeared to be produced primarily by gas flow from the gob, not from increased emissions from the face. Barometric pressure variations were substantial over the course of the study and varied on a diurnal basis, as is typical of many mining operations. Suggestions are forwarded for reducing longwall face methane concentrations.

Jan 1, 2012

By Christian Neumann, Josef Arnold, Albin Reinhart

The Channel Tunnel Rail Link (CTRL) is the most significant railway infrastructure development project in the United Kingdom since the construction of the Channel Tunnel between France and England. The key element of this project is the 2-mile-long(3.2-km) North Downs Tunnel, which will be the largest and deepest twin-track railway tunnel ever constructed in the United Kingdom. This paper describes the contractual agreement, the design and construction (excavation and lining) of a twin-track rail tunnel with a 166-m 2 face excavated through chalk using the New Austrian Tunnelling Method (NATM). The importance of collaborating with a tunnel contractor/designer who not only is expert in the New Austrian Tunnelling Method, but who was also responsible for the design and installation of the primary lining, will be highlighted in this paper. This paper will also deal with the benefits of partnering in tunnel design and construction, as well as the resultant added values of mechanizing conventional tunnelling methods (Value Engineering).

Jan 1, 2001

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007