Search Documents

By Fred A. Glover

It's a pleasure to be included with this group. I am not here to sell my services, but rather to share with you some ideas and considerations on using environmental consultants. Environmental consultants have developed some problems as well as created new costs for companies that are as legitimate as engineering costs. Each day the mining industry is becoming more affected by the proliferation of environmental regulations and their interpretations by federal and state agencies. How does a modern mining company cope with all the demands for environmental consideration by regulatory agencies and special interest environmental groups-- yet produce a product and make a profit? One way is to make efficient use of environmental consultants. But, as everyone here knows, this approach has been fraught with seemingly inherent frustrations, difficulties, and much justified criticism.

Jan 1, 1979

By José Ricardo Lopes, Alaor Coelho, Marco Gomes, Alfredo Dacio Moraes Filho, Akira Koshima

"Very low strength alluvial peat soil was found under two old drainage galleries with just 4.3m cover above a twin tunnel due to be excavated by a 10.6m diameter EPB Shield for São Paulo Metro’s Line 5. Alignment was required to strengthen soil and drive the TBM through safely without damaging the galleries. The design included six levels of self-drilling forepoling with lengths up to 15m, using 100 mm-diameter SCH160 metal tubing and injection bulbs with estimated 0.20m diameter. Two 6m-diameter circular shafts were excavated along the shield-tunnel axis, one each side of the galleries, and forepoling fanned out under gallery foundations. Given the peculiar soil and confined working space, more data were needed for correct drilling geometry. Ground mass treatment was successfully designed and executed and galleries were fitted with instruments to enable the shield’s advance. DESCRIPTION São Paulo Metro’s Line 5 (aka Lilas or purple line) is adding 11 stations along an 11.5km extension and three EPB TBMs are being used simultaneously (three EPBs on the same job for the first time in Brazil) with one of them excavating a large cross- section twin-track tunnel. Currently the largest work-in-progress for São Paulo Metro, this project has been divided into seven lots and 9km are already operational. This study refers to Lot 6 where the 10.6m - diameter EPB shield excavation is only 4.3m below two galleries running through a 10m layer of very soft peat soil in an old alluvial riverside region ringed by major roads. After recent filling, this area (Parque das Bicicletas) was used for recreation, although temporarily it has become a construction site. This paper will describe the original basic design; precautions in relation to the structural condition of the galleries after inspection; the problem of absence of data for their foundations; subsoil bore tests; evolution of the engineering design for the galleries and conditioning and reinforcing the soft soil below the galleries to ensure safe advance of the EPB shield, and finally the successful outcome of the solution used."

Jan 1, 2016

By Michael Cruickshank

All life on Earth relies on the ocean and yet the ocean is 95 percent unexplored, unknown and unseen by human eyes,? said Paula Keener, director of education programs for National Oceanic and Atmospheric Administration?s (NOAA) Office of Ocean Exploration and Research. ?To better understand, manage and protect the ocean and its resources, NOAA believes it is critical to use the best technology to explore, discover, inform, educate and motivate? (MTS, newsletter, January 2011). In the last few decades, our understanding of the global mineral resource base has been drastically changed by some surprising new developments. The potential for commercial minerals per unit area in the oceans and seabed appears to be similar to that of the terrestrial lands. Thus, almost three-fourths of the global mineral resources are in, or under, the sea and are virtually undeveloped. The area of the Pacific seabeds alone is greater than the total area of the global lands. Half of the global seabed minerals are now controlled by nation states within their Exclusive Economic Zones (EEZ). The other half is controlled by the United Nations (UN) through the International Seabed Authority (ISA) within the ?areas beyond national jurisdiction? known as The Area. Thus, the Law of the Sea, ratified in 1994, has resulted in the largest transfer of control of natural resources in the history of mankind. This paper was prepared by the Society for Mining, Metallurgy and Exploration (SME) Committee on the Offshore Technology Conference for the SME Board of Directors and other interested parties. As the premier professional society for the mining and mineral community in the United States, with a history dating back to the 19th century, SME?s mission is to encourage and support young men and women engineers in the minerals industry, provide the services they need, improve the image of the industry, strengthen the networking among global industry professionals and engage in proactive collaboration among industry, government, academia and nongovernmental organizations (NGOs). The accomplishment of this mission can be strongly advanced by highlighting what is probably now the most significant development in the history of the modern minerals industry - the exploration of the marine environment and the understanding of the potential for the development of the minerals therein.

Jan 1, 2011

To maintain its brand position in the competitive market of mining equipment, the Volvo Construction Equipment (Volvo CE) engineers were challenged to develop top-performing wheel loaders and articulated haulers even faster than before. To start, this meant reducing prototype test cycles by two-thirds. The final goal? Chopping in half the virtual prototyping time in early design phases. Creating a unified co-simulation solution In this ground-breaking project, the Volvo Construction Equipment design team in Eskilstuna, Sweden, replaced its piecemeal department-by-department process with a single solution based on LMS Imagine.Lab AMESim. With one unified model, they could simulate the behavior of four major vehicle subsystems in wheel loaders and articulated haulers: hydraulics, powertrain, thermal management and the actual driver. Subsystem models exchanged data seamlessly.

Jan 1, 2011

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989

By C. A. Fleming, K. W. Sarbutt, P. K. MacPhail

The SART process has been developed for Teck to treat bar­ren solution from the cyanidation/CIP process that has been developed for the Lobo-Marte project in Chile. The objective of the process is to recover cyanide in a form that is suitable for recycling to the leaching part of the process. The Marte and Lobo ore bodies require a dosage rate of about 2 kg/t NaCN, of which only 0.5 kg/t is truly consumed (as thiocyanate, cyanate and ferrocyanide species). The remaining -1.5 kg/t is present as cop­per cyanide (-1 kg/t) and free cyanide (-0.5 kg/t), and is poten­tially recoverable and recyclable. SART is an acronym that describes the unit operations in this cyanide recovery process; namely, .. Sulphidization .. Acidification .. Recycling of precipitate " Thickening of precipitate The basic chemistry has been applied previously, and has also been the subject of two patents (American Cyanamid Company, 1965, Potter et al., 1986). The process involves the conversion of all free and WAD cyanide in solution to hydrocyanic acid by acidification of the tailings solution to pH :s,4, and the conversion of all copper in solution to cuprous sulphide (synthetic chal­cocite) by the addition of a sulphide salt:

Jan 1, 1998

By Marlin D. Schutte, Graham M. Fraser, Paul M. Kubera, Ronald J. Weetman

Mixers play an important function in the operation of multi-phase reactors in the minerals processing industry. They must suspend solids, transfer oxygen, maintain pH and temperature uniformity, assist in heat transfer, and, in biological processes, avoid the development of excessive shear rates. The LIGHTNIN A315 impeller (Figure 1) effectively supersedes the older Rushton turbine (Figure 2) which has been classically employed in gas­Iiquid-solids applications such as bacterial oxidation, cyanide destruction, etc. Since a stirred tank reactor can be such a key part of the overall process, it is essential that the mixers be designed for long term reliable operation, both process and mechanical, to insure a high percentage of on-line availability. Mixers in gas-liquid-solids processes may experience extraordinary loading conditions which must be taken into account to guarantee a robust mechanical design. Given the recent trend towards the design of world-class process units with maximum capacity equipment, there is increased importance and emphasis on the integrated design of the complete agitation system -mixer, vessel, and structure -to insure trouble free, post­commissioning performance. This paper presents some of the considerations necessary to specify the process functions of the mixer in multiphase applications, as well as special considerations for the mechanical design of the integrated reactor system.

Jan 1, 1993

By Elif Emil-Kaya

Samarium (Sm), as one of the rare earth elements (REEs), has gained significant attention in the production of samarium- cobalt (SmCo) magnets due to their high corrosion and oxidation resistance, as well as their high-temperature stability. SmCo magnets find applications in various industries, including but not limited to national defense, aerospace, military and medical equipment. Sm and Co have been classified as critical metals due to their economic importance and supply risk. Recovering Sm from SmCo magnets is an effective method to ensure a stable supply. The present study investigates an integrated hydrometallurgical treatment and combustion process for the preparation of rare earth oxide (Sm2O3 ) powders from SmCo. Initially, SmCo powders are exposed to nitric acid, and the resulting slurry is selectively oxidized at 250 °C to obtain Sm(NO3)3 , Co2O3 and Fe2O3 . Subsequently, the selectively oxidized powders are leached with water to extract Sm. Sm2O3 powders are produced from the obtained leaching solution using an energy- and time-efficient solution combustion process. Finally, the optimal conditions for the production of Sm2O3 are identified, and the produced powder is characterized through X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) analysis.

Nov 1, 2024

By Euclid P. Worden

In 1977, an article in World Mining (1) reported a total of 2726 rotary blast hole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher: Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item, to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to re¬ducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, five factors affect the rate of penetration. They are: 1. Bit selection 2. Weight on the bit 3. Rotary speed 4. Hole cleaning 5. Formation properties Of these factors, all but one may be control¬led by the operator. Looking at any one in detail may reveal possible improvements in the system. Cleaning the hole is a good place to start. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh, clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in re drilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole.

Jan 1, 1979

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By William E. Mead

A regional investigation to find large supplies of potable ground water was carried out at elevations exceeding 12,000 feet above sea level on the Bolivian Altiplano. The program marked the first application of modern ground water search and development technology in the region, and ended a history of unsuccessful exploration efforts to locate important supplies of fresh water from underground sources. Oruro, a population center of 90,000 inhabitants, and its primary supporting industry - mining, both derived major direct benefit from the results of this program.

Jan 1, 1970

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

By Emily Wortman-Wunder

Attendees at December?s Arizona SME Section Conference at the Hilton El Conquistador Resort outside of Tucson, AZ were feeling optimistic and ready to get to work after a year of steady growth and recovery in the mining industry. During the two-day event (Dec. 5-6, 2010) and the preceding American Mining Hall of Fame banquet and awards ceremony, the focus was on copper, worldwide population growth and regulatory pressures, with several smart new projects featured alongside updates to traditional large-scale copper development projects. Keynote speaker Timothy Snider, chair of the University of Arizona?s Lowell Institute for Mineral Resources, hit the mood of cautious optimism when he analyzed the global demand for resources, using the case example of copper. Over the next 20 years, he said, the world?s population is expected to grow to 9.2 billion and the average annual per capita copper use is expected to rise from 2.2 to 4.5 kg (5 to 10 lb). The increase in demand will provide tremendous opportunity for mining companies, he said, but cautioned that the opportunities are balanced by negative influences on demand and pressures on supply. While demand for copper is currently growing, Snider noted that there were significant downward pressures on demand as well. These included a western world that is overbuilt, in-creasing use of substitute materials in new construction and the rise of wireless devices. He also noted new regulatory pressures, and pointed out that resource development now had to occur within a context of sustainability on several levels.

Jan 1, 2011

By S. Tafazoli, N. Himmelman, D. Chan, E. Chow

"While Wearable Technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply Wearable Technology to improve productivity and safety in the mining industry. This paper discusses the value proposition of using Wearable Technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to Wearable Technology, are defined. Finally, the concept of MetricsGear™, the first Wearable Technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear™ is designed to notify the user with minimal distraction to keep the user focused on their primary task, and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. INTRODUCTION The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: time-critical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some Human-Computer Interaction (HCI) experts classify notification types based on the Interruption, Reaction, and Comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction, and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, E. 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, M. 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing, and information to identify which equipment and when the tooth went missing (see Figure 1). Contextual information is relevant information that is valuable for the receiver to be aware of as it can present an opportunity to improve efficiency or save cost. According to the IRC framework, contextual information is classified as low interruption, low reaction, and high comprehension. They are not as urgent as time-critical events, but provides more detailed and informative information to assist the receiver. For example, when a shovel’s worn tooth is predicted to require replacement soon, a notification to a GET technician can help him or her schedule a pre-emptive replacement of the tooth in an already planned maintenance to prevent having to reactively schedule another one when the tooth is critically worn. This helps reduce the amount of equipment downtime to maximize production (Baumann, M. 2013). In this case, the receiver will look at the information when he has a moment to spare to get a quick forecast, and make use of this information as needed (see Figure 2)."

Jan 1, 2015

By BURCU NILGUN CETINER, Serdar Aktas

Antimony has been used extensively in industry and in everyday life since the 19th century, and antimony sulfides have been known since around 4,000 B.C. Antimony’s most significant applications are as a flame retardant in the manufacture of electronics and textiles, as a catalyst for plastic fabrication, and as paint pigment and fining agent in glassware, opacifier in ceramics and an alloying element in ammunition and battery manufacturing plants. It is also used in vehicle brakes and tires. Brake pads contain stibnite (Sb), the sulfide compound of antimony. In particular, stibnite is used in automobiles as a lubricant, vibration reducer and friction stability improver. Anthropogenic activities are the primary source of antimony in the atmosphere [1,2]. Annual global consumption of antimony has increased to more than 1.4 × 105 t, and China is the most significant producer [2].

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion (Li-ion) battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Li-ion batteries can go through a thermal runaway under different abuse conditions, including thermal, mechanical and electrical abuse, leading to a fire or explosion. The National Institute for Occupational Safety and Health (NIOSH) mining program is conducting research to prevent and respond to lithium-ion battery fires in battery-electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, Class D extinguishing powder and water mist for lithium-iron-phosphate (LFP) battery pack fires. The effects of activation time and release time of the water-mist system on the suppression of the LFP battery (a type of Li-ion battery) fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Aug 1, 2024

By Martin J. Hughes

The Eagle Mountain Mine of the Kaiser Steel Corporation is located in the California portion of the Colorado Desert at a distance of about 60 miles east of Indio, California. At the present time, this mine is producing at the rate of 5,000,000 tons of concentrate per year. A total of 1,000,000 tons of ore per year is presently being sold on the Japanese market while the remainder is consumed by the Kaiser Steel Company blast furnaces at Fontana, California. A new Pellet Plant and Concentrator is presently under, construction with completion scheduled for May or June 1965. This plant will have a rated capacity of 2,200,000 tons of pellets per year and essentially all of this production will be sold to Japanese steel companies.

Jan 1, 1965

By H. G. Schoenike

A subsequent spin off of the energy shortage is the new life for barite. Over 90% of the barite produced in the world is used as a weighting material in oil well drilling muds. Business is booming; the price of barite has risen; scarcity is imminent, and exploration is going full steam ahead. New barite-producing companies are being formed and many of the barite consumers are considering becoming producers. Prospectors have found a new "love," smaller deposits are being explored, and old deposits, previously rejected, are getting a reappraisal. Even barite tailing piles are being resampled.

Jan 1, 1980

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The study proposes a dynamic path planning method for mining equipment based on spatial kinematics and real-time correction of coal-rock state identification. The method integrates real geological data and equipment operation information to improve the autonomous cutting of fully mechanized mining equipment.

May 1, 2023