Search Documents

By Y. H. Cheng, H. EI-shall, S. Gupta, N. A. Abdel-Khalek

A 14.6 cm (5.75 in.) diameter by 1.83 m (6 ft) tall laboratory-size column is used in flotation of Florida phosphates of different feed sizes. In this paper, the effects of different parameters on the flotation efficiency of coarse particles (belt feed, -1.4 + 0.5 mm, i.e., 14 x 35 mesh) under negative bias are discussed. Parameters included collector dosage, frother type and dosage, and conditioning water, which contained a residual concentration of collector. Flotation tests were performed using statistical designs. The results strongly suggest that flotation performance is dependent on the used combination of reagents. Interactions between frothers and the collector and, consequently, the flotation efficiency were found to be dependent on frother type and presence or absence of conditioning water. Under the negative bias, an excellent recovery of more than 98% of phosphate was achieved in concentrates of high grade (above 31% P205) from such feed of coarse particles.

Jan 1, 1999

By Willard C. Lacy

Discovery of a mine is a complex affair. No mine is simply found but comes about through the efforts of many. It is difficult to establish "credit" when a mine is found and becomes a viable operation, or "guilt" when a mine is lost, goes bankrupt, or remains undeveloped. The story of the Toquepala and Cuajone developments entails various stages of: (1) discovery and recognition; (2) testing and innovation; (3) political and industrial negotiation and intrigue; and (4) finance, development, and operation. The Toquepala and Cuajone projects introduced innovative drilling techniques, were among the first major porphyry copper deposits to utilize induced polarization (1P)geophysical methods, were among the first deposits to undertake complete feasibility studies on drilled- out ore bodies, and were developed by the first large Western Hemisphere copper mining consortium. Many persons have contributed to the development of these two great deposits. Some of the names have been lost and certain contributions have gone unrecognized. I apologize for these omissions.

Jan 1, 1991

By R. Wisniewski, S. Schafrik

Every underground coal mine in the United States must deploy and operate a wireless communication and electronic tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. This paper assumes that the tracking system uses the communication system to perform its operation. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 24 hours, and the requirements in the MINER Act for the tracking systems to be “functional, reliable and calculated to be serviceable” and the communications systems “redundancy.” These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using tools that are available to and commonly used by the reliability, maintainability and availability community.

Jan 1, 2014

By Michael J. Sapko, Robert A. Cortese

A flame powered trigger device has been developed to explosively activate suppression barriers to quench gas and coal dust explosions. The important feature of the device is a silicon solar panel, which collects 0.3 p to 1.1 D wavelength radiation from the developing explosion, and generates electrical energy to initiate a detonator, which in turn causes the rapid explosive release of an extinguishing agent into the advancing flame front. Solar panels that are rated to produce 20 w of electrical power when exposed to the sun light are producing about 200 w when exposed to full-scale dust explosion propagating in the U.S. Bureau of Mines' Lake Lynn Experimental Mine. The solar panel is electrically isolated from the detonator by a pressure sensitive switch until the arrival of the precursor pressure pulse, which always precedes a deflagration. This combination of pressure arming and flame powered photo generator prevents false barrier activation and requires no external power supply.

Jan 1, 1991

By J. Alvarez, S. H. Castro

The feasibility of chalcopyrite-pyrite separation in the flotation of a chalcopyritic copper ore, at reduced surface tensions regulated by methanol, was investigated. It was found that with methanol dosages from 0.5% to 1.5% v/ v, the chalcopyrite might be effectively separated from the pyrite, without use of other flotation reagents and pH regulators. However, under this simple condition, the chalcopyrite recovery was only around 50%, recommending the use of other reagents to reinforce the collector action. Low dosages of different collectors were tested, including SF-323 (Shell Float), S-6588 and S-7251 (Cytec), and S-701 (Molycop). Very promising results were obtained with low dosages of the collector S-701 and 1% v/v of methanol in the pulp, which evaluated against a reference test, gave similar copper recovery, higher Mo recovery and higher depression of pyrite. Consequently, this is an alternative process which does not require the use of lime to depress pyrite.

Jan 1, 1995

By D. Tao

The presence of insoluble slimes in potash ore poses a serious processing problem to the potash industry. These insolubles must be removed prior to potash flotation because of their high adsorptive capacity for amines which are generally used as collectors in the subsequent sylvite flotation. This is usually accomplished by scrubbing of the ore in brine followed by hydrocyclone classification to separate slimes from the salt particles. Insoluble slimes that remain in the ore after the desliming procedure are depressed by reagents such as guar gum or starch during sylvite flotation. In this research, the feasibility of using GP clay binders to replace guar gum for potash flotation was investigated. Batch mechanical flotation tests were conducted with the potash samples provided by a leading potash company. It has been found that GP clay binders increased potash concentrate yield and recovery at the same product grade. Effects on potash flotation efficiency of flotation process parameters such as impeller rotation speed, slurry temperature, binder type, dosage and conditioning time have been investigated to establish the optimum conditions for flotation. Binder GP374G33 has been identified as the optimum substitute for guar gum as slime depressant in potash flotation.

Jan 1, 2008

By John E. Miller

In recent years there has been increasing concern in the mining industry over the availability and high cost of diesel fuel to support mining operations. Unit Rig & Equipment Co. has been deeply involved with the development and testing of the newest designs for trolley assist. Beginning in dune 1980, Unit Rig modified and commissioned six 156 metric ton (170 short ton) trolley assist haulage trucks at two mine locations in South Africa. Operating haulage trucks with General Electric GTA 15E/776 drive systems were chosen for the tests since this size of truck represented the majority of the population of large size haulage trucks and the greatest technical development problems. Test operations have proven the feasibility of equipment designs in actual operation and preliminary economic data has convinced the operators to proceed with planning to modify their entire mining operation to use trolley assist. The initial capital investment incurred for trolley assist can be recovered in a short period of time. Following this quick capital recovery, mines will continue to realize lower operating costs through increased productivity and lower diesel consumption.

Jan 1, 1980

By Yi Luo, Hua Jiang

A roof bolting drilling operation in an underground coal mine can expose the operator to a high concentration of respirable coal and crystalline silica dusts (smaller than 10 µm). Overexposure of high-level quartz dust for a roof bolter operator can lead to the development of silicosis in as little as three years [1]. This study proposes a drilling control algorithm for the bolt hole drilling process. This algorithm can be integrated into a current drilling control system on the roof bolter machinery and is expected to reduce the generation of respirable dust while enhancing the energy efficiency of the roof bolter machine. In addition, the drilling efficiency and bit condition can be evaluated while drilling based on the real-time feedback parameters. This capability enables the algorithm to ensure the drilling is performed under a relatively high energy efficiency with less respirable dust generation and to avoid drilling with an excessively worn bit that can cause bit clogging or steel buckling failure.

The sixth annual conference of the Mineral Economics and Management Society (MEMS) was held Feb. 27 through March 1 in Boulder, CO. This year's event was attended by more than 100 academic, industrial, government and other professionals interested in mineral economics and materials management. With about 250 members worldwide, this not-for-profit society seeks to promote scientific and economic analysis of current relevant issues. This year's program was sponsored by Alcan, Bateman Engineering, Cyprus Amax Minerals, J.P Morgan, Knight Piesold LLC and Newmont Gold. The conference's technical program consisted of six sessions. These included "Financial tools for a changing world," "Access to minerals," "Comparing North and South America," "Environmental issues in today's world" and "Transporting minerals." The program was concluded with a panel discussion titled "National minerals policies in Asia." In addition, a student papers session was held, in which students were given the opportunity to compete for a $1,000 award. The following is a brief review of the technical pro¬gram.

Jan 1, 1997

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By John H. Archibald, Arthur L. Miller, George A. Savanick

As part of its continuing research on selective mining, the Bureau of Mines has made progress toward developing a tool capable of remotely extracting hard minerals through a borehole. As the successor to the successful borehole miner, which extracted soft materials through a straight borehole, this new device has several innovative features: 1) it can propel itself in and out of an 8-inch borehole; 2) it can cut hard rock with an abrasive jet and transport the cuttings to the surface; and 3) it can negotiate deviated boreholes--the feature that enables it to follow a vein and extract only the values. This paper describes the development and feature testing of the reamer/miner.

Jan 1, 1991

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the micro- computer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user pro- grams to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to en- courage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Har- mon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the com- puterized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage ) , the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 1, 1988

By C. Fuellenbach, J. Brune

"INTRODUCTION Mining activities must be safe and profitable. These two requirements influence each other. The purchase and implementation of safety improvements costs money. Injuries and illnesses at mines stop or delay production and may result in additional costs or a loss of profit. Other effects of injuries and illnesses include the negative influence on employee morale, corporate reputation and conflicts with contract partners. Based on this researchers asked the question: are mines with lower rates of injuries and illnesses more profitable than mines with a higher frequencies? One aspect of this research is the evaluation of the safety situation and the measurement of benefits of safety improvements in the German mining industry. In the following paper, this part of the research will be examined. The main aim is the evaluation of injury rates in different German mining sectors and regions in Germany. SELECTION OF GERMAN MINING OPERATIONS The research team decided to focus the study on the salt and potash and the aggregate and industrial minerals mining industries in Germany. These two mining industries are different in the number and size of operators, structure of the industry, pricing and markets. The selection of two different industries adds to the clarity of the evaluation. Salt and potash mining industry The German salt and potash industry is primarily located central Germany. All salt and potash mines in Germany are underground operations. In 2015, the German potash industry employed 8,100 employees and generated a total revenue of 2 billion Euros. German potash reserves include magnesium compounds like kieserite (MgSO4·H2O), in addition to sylvite (KCl) and carnallite (KMgCl3·6(H2O)). The German salt industry employed 2,300 people in 2015 and generated revenue of 800 million Euros (Krueger, 2015) There are seven mining companies with salt and potash operations: esco-european salt company GmbH & Co. KG, K + S Kali GmbH, Saline Luisenhall GmbH, GSES Glückauf Sondershausen Entwicklungs- und Sicherungs-gesellschaft GmbH, Südwestdeutsche Salzwerke AG, Wacker Chemie AG and Südsalz GmbH. In this way, esco – european salt company GmbH & Co. KG is an affiliated company. Esco was founded as a joint venture of K + S and Solvay in 2002, since 2004 K + S is the sole holder (esco - european salt company GmbH & Co. KG, 2016). Likewise, the Südwestdeutsche Salzwerke AG has a controlling interest in Südsalz GmbH (Südsalz GmbH, 2016). Aggregate and industrial minerals mining industry The aggregate mining industry in Germany is comprised of many small mining operations and relevant companies. According to the German Department of Economics (BMWi, 2015), the following industrial materials are classified as aggregates: fluorite, barite, kaolin, quartz and quartz sand, quartzite, silica, loamy and foundry sand, pegmatite sand, shale, clay, bentonite, schistose, limestone and dolomite, gypsum and anhydrite, basaltic lava and lava sand, gravel and split, pebble and silicic sand and peat."

Jan 1, 2017

By G. E. McKelvey

A group of gold deposits in southeastern Ecuador, near the town of Zamora, have become the focus of intensive mining activity, due to their extremely high gold grade (unconfirmed reports of about 50 g/t or 1.4 oz per st, or more). The deposits at Nambija and other prospects in the district are hosted by a sequence of sedimentary and volcanic rocks that are present within a large xenolith orpendant within alkalic phases of the Jurassic Zamora Batholith. The xenolith, unknown in size, is composed of various island arc lithologies (limestones, shales, sandstones, tuffs and flows). All have been altered to some degree by skarn-hornfelde alteration assemblages. Mineralized areas appear to be localized within a linear zone containing tectonic and intrusion breccias that cross-cut a complex calcic skarn assemblage developed within the xenolith. Although the nature of the host rocks appears to have exerted some control on mineralization, the high-grade ore is concentrated along north-northeast trending breccias, faults and dikes that crosscut the flat-lying stratigraphy and skarn alteration as suggested by the strong linear trend of workings in the district.

Jan 1, 1991

By Paul C. Lingo

The title of my talk today might lead you to two logical conclusions: The industry is faced with a problem that requires a solution and after discussing the problem I will offer a solution. The first conclusion is painfully accurate. One need only look at the accident statistics to be aware of the problem. During the eight-year period 1954 through 1962, the United States Bureau of Mines reports that falls of rock and coal accounted for 1,435 of the 2,516 fatal injuries that occurred in underground bituminous coal mines. Some improvement was made during 1962. For the first time since records have been kept, falls of rock and coal accounted for less than 50 per cent of the underground fatal injuries. The 105 deaths recorded in 1962 indicate that a great amount of work remains to be done in this area. As to the second conclusion, let me assure you at the outset that I have no panacean solution; however, I do propose to discuss some aspects of the problem and some possible methods of solution. What methods of solution are now, or have been employed in attempting to solve the problem? More specifically, what methods have you and your associates used? Has it been an orderly well thought out approach to the entire problem, or has it been a somewhat piecemeal approach which tackled the immediate problem and left the total problem for another day? Perhaps a new approach may be in order.

Jan 1, 1964

By R. W. Smith, M. C. Fuerstenau, G. X. Xang

Nonliving dried water hyacinth (Eichhornia crassipes (Mart.) Solms) roots were investigated for the biosorption of cadmium, lead and other heavy metal ions from aqueous solutions. Dried water hyacinth roots, when suspended in solution, strongly and rapidly sorb several different metal ions. Factorssuch as reaction time, pH, the initial concentration of metal ions, the presence of other metal ions and biomass concentration were investigated. The adsorption was shown to follow the generalized Langmuir adsorption equation. The relative affinity of the roots for lead is greater than that for cadmium. The batch sorption kinetics of the uptake of cadmium and lead can be described by an apparent first-order reversible reaction model. The roots could be regenerated after the metal ions were stripped. Successful desorption of Cd and Pb from the biomass by acidic CaCl2 solutions revealed that the metal uptake phenomenon is reversible, implying physical sorption of Cd and Pb.

Jan 1, 2000

By Ken Takahashi, Yuuich Umeki, Masahiko Arakawa, Dr. Tominaga. Yuusaku

Macroscopic characteristics of a complicated mine ventilation is remarked to build an expert system for mine safety in the Taiheiyo coal mine, Hokkaido, Japan. To gain the characteristics a large number of simulation were performed with varying aerodynamic resistance of the branches with regulator in mine ventilation network. The principal results of the study are as follows, (1) Pressure loss diagram for ventilation network with main and auxiliary fans enables capability of air circulation in the network. (2) H-Q (pressure-quantity) diagram gives capacity of air quantity In a network with main and auxiliary fans. (3) When airflow rate, [] through branch qi is changed by opening/closing regulator set in the branch, air flow rate, [], through branch p can be represented by the empirical formula. [ ] where Api and Qp,o are the constant coefficients. (4) Macroscopic characteristics mentioned above are available to make rules in an expert system for escaping route at emergency.

Jan 1, 1989

By Chee Theng

"Keep calm and carry on mining. That has long been the conventional wisdom in the mining industry, a largely cyclical one that has weathered roller-coaster booms and busts. But in the years from 2002 to 2016, an unprecedented steep rise in commodities prices that lasted a decade and then took a sharp turn downward had made it hard for gold and silver miners to stay the course.“The last 15 years highlighted some of the structural and inherent challenges that our industry has, from product price uncertainty to long lead times to the capital intensity of our business,” said Mitchell Krebs, president and chief executive officer of Coeur Mining, who was the luncheon speaker at the American Exploration & Mining Association’s 122nd Annual Meeting held Dec. 5-9, 2016, in Reno, NV.Looking back, Krebs said, “We were given this enormous gift of a commodities super cycle, and the industry kind of blew the opportunity.” While gold prices rose 319 percent and silver prices rose more than 200 percent over the 2002 to 2016 period, the XAU index of 30 gold and silver mining companies’ stock prices went up by only 20 percent.Entering 2016, precious-metals prices have made a comeback, with gold rallying strongly from a six-year low at the start of the year. This time, the industry is ready. Companies are leaner and meaner, with lower costs, reduced debt and an increased focus on higher grades and quality ounces. Although opportunities were missed in the past, the industry has got its act together and is now well positioned to take advantage of a price upswing and even to show profits when prices fall, as they did in August 2016, pushed down by a strong dollar."

Feb 1, 2017

By V. V. Ershov

Mining geometrical graphic documentation is employed on a large scale in designing and planning of mining operations at all the stages of exploitation. Mining geometrical modelling of mineral grade distribution presents an independent type of mathematical (graphic) modelling. The idea of functional relationship between geological indices being observed, and spicier coordinates is the basis of traditional mining geometrical modelling. Graphic presentation of three independent variables P =f (x,y,z) is confined to obtaining the series of two independent variables functions. Independent variables are presented as topographic surfaces corresponding to plane cross-sections of a deposit. During exploitation of certain parts of a deposit the most reliable geological information is obtained, characterizing regularities of ore distribution in the entrails. This information is, though, not taken into account in goemetrization of the new areas. In this connection dynamic modelling of deposits in the process of exploitation is necessary, i.e. geometrization of the deposits should be dynamic.

Jan 1, 1986

By Colleen A. M. Gibbs

On July 30, 1979 New Council on Environmental Quality (CEQ) regulations for implementing the procedural provisions of the decade-old National Environmental Policy Act went into effect. These new regulations replace approximately seventy different sets of agency regulations, providing some uniformity throughout the Federal government in the conduct of environmental reviews and preparation of environmental impact statements (EIS). This attempt by the Federal government at a general improvement in the preparation and quality of EIS's presents an opportunity for the mining industry to evaluate how the EIS process for mining proposals can be expedited. The environmental impact statement is often a key element on the critical path of a major mining project. Preparation of the EIS is ordinarily the responsibility of the Federal agency with primary decision-making authority over the project. Still, the proponent, i.e. the mining company, can play a major role in the process and have a major impact on the timeliness and adequacy of the effort. Typically, the Proponent will conduct (or will hire consultants to conduct) environmental baseline studies of, for example, air quality, wildlife, geology, water quality, vegetation and archaeology. These studies are then compiled into an environmental report and submitted to the agency. The agency verifies the data and incorporates them into the environmental impact statement.

Jan 1, 1979