Search Documents

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

"Above ground, elevated belt conveyors with span >200m between support points can cross valleys, rivers, forests and buildings with minimal footprint. The Cable Bridge Conveyor is a new type of suspension bridge based belt conveyor system that has long span between support points. It combines typical belt conveyor and the improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The Cable Bridge Conveyor’s compatibility with current belt conveyors allows the versatility in application. INTRODUCTION Belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground based or elevated conveyors (1). The ground based conveyor has the lowest structural cost, where the conveyor is laying on an existing road. Maintenance access is easy and straight forward. Compared to the ground based conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has smaller footprint, and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss type structures, with typical span of 15m to 25m between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of triangular truss supported conveyor is around 30m to 40m, while the weight is about 10% less than conventional box truss with shorter span (2). Long span elevated structure based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100m~400m and beyond. The very wide distance between support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2015

By Duncan M. Lamb

Commercial computer "time-sharing" is a new and powerful tool for the engineer. It is a system of virtually simultaneous use of a digital computer by several individuals. Access to the computer is by means of a conventional teletypewriter which transmits over the regular telephone lines to the computer which may be located any distance from the user. Complex or repetitive computations can be programmed and the speed of computation is many times that which one can do with slide rule and desk calculator. The availability of such a commercial computer "time-sharing" system offered an opportunity to transform a tedious and time-consuming task into one that requires only a few minutes. Until the work of F. C. Bond produced widely accepted mathematical statements concerning the performance of grinding mills, the selection of the proper size equipment was done by comparison with similar operating equipment. Allis-Chalmers systematized Bond's work in a bulletin published in 1963 but the calculations are laborious and the final mill selection still required comparison of the calculated power draw with the power requirements listed in equipment catalogs. This was, however, a step forward from previous procedures. This paper discusses a rapid and simple method of determining the size and power requirement of overflow ball mills. A shared-time computer program has been developed which rapidly calculates and displays the physical dimensions, power requirements, grinding media size and quantity, as well as the important correction factors used. All of these data are calculated from input information which is usually available.

Jan 1, 1969

By W. G. Cornwall

The mining field, inclusive of the treatment plant is located in the foothills, five miles inland from the northern coast of Viti Levu, the largest and most important island of the Fiji Group. Gold and silver occur as tellurides, associated with the sulphides, and as minor occurrences of electrum.

Jan 1, 1975

By Julian Glasser

Starting with rutile, containing more than 55% TiO2 and of the proper particle size, the commercial production of titanium tetrachloride via fluidized bed chlorination is relatively very simple and economical. As compared to shaft chlorination, it operates at a much higher capacity for given sizing of equipment, and appears more foolproof, requiring less attention. Operating data were obtained on a 53" diameter fluidized bed chlorinator using Australian rutile and petroleum coke of controlled particle size. Production rates varied from 20 to 50 tons of crude TIC14 per day for a campaign extending over one month. Close to theoretical yields and efficiencies were obtained from the viewpoint of chlorine and/or rutile consumption. Details of important equipment design, critical operating conditions and pertinent results are described.

Jan 1, 1962

By W. C. Hellyer

The Granduc ore body is located beneath glacial terrain on the borders of British Columbia and Alaska, some 600 miles from Vancouver and 30 miles from Tidewater at Stewart, B. C. The concentrator and attendant facilities are located in wilderness country at an elevation of 2500 feet. The average annual snowfall is 65 feet. Surface facilities and ore body are linked by a 10 mile railroad haulage tunnel. This copper property has been developed by Granduc Operating Company on behalf of Newmont Mining Corporation and American Smelting and Refining Co. First production started in November, 1970. In August, 1966, Granduc Operating Company awarded an engineering and construction management contract to McKee-Swan Wooster, a joint venture of A. G. McKee of Canada and Swan Wooster Engineering Company Limited, to design a concentrator to treat approximately 7000 tons of ore per day. The isolated location of the Granduc ore body indicated comparatively high freight rates on consumable items of concentrator supplies such as reagents, grinding media, etc. A firm flowsheet for the flotation of the Granduc ores having been developed by the Danbury laboratory of Newmont Exploration Limited, attention was devoted to means of reducing operating costs. One obvious method was to reduce or eliminate the costs of steel grinding media by employing some form of autogenous grinding. two pilot plant operations were carried out at the facilities of Lakefield Research of Canada Limited, in which autogenous grinding of Granduc ores was investigated. The results of these investigations led to the selection

Jan 1, 1972

By L. Mao, R. Yoon

The thin film balance (TFB) technique was used to measure the equilibrium thicknesses of the water films formed between two oil phases. The measurements were conducted with dodecane at varying concentrations of dodecylammonium chloride, pH, and electrolyte concentration. The data obtained in the present work were used to calculate the surface forces acting between the two oil phases. The calculation was carried using the Extended-DLVO theory with the surface potentials calculated from the Gibbs adsorption isotherm. The results show that oil droplets suspended in water are hydrophobic and the hydrophobicity changes with surfactant and electrolyte concentrations.

Jan 1, 2004

By Garland R. Dever

Limestone resources for industrial, constructional, and agricultural uses occur on the surface and at minable depths in several areas along the Ohio River and its navigable tributaries in Kentucky. Operable thicknesses of high-calcium and high-carbonate limestones suitable for use in cement and lime production, steel manufacture, environmental-control measures, and other special uses are documented in Ordovician and Mississippian formations by analysis of 0.3-meter (foot-by-foot) samples. Active and potential mine and quarry sites afford access to water transportation and proximity to a number of industrial and metropolitan centers. Geologic factors affecting the distribution of deposits include the Cincinnati arch, regional dip into the Appalachian and Eastern Interior basins, complex faulting in and near the Western Kentucky fluorspar mining district, and late Paleozoic erosional unconformities in northeastern Kentucky.

Jan 1, 1977

By Terry Ritzel

Predictive maintenance technologies include vibration analysis, tribology, infrared thermography, ultrasonic detection and electrical measurements. These technologies have been applied to large electric mining shovels at the Cyprus Sierrita Mine outside of Tucson, AZ. The predictive maintenance program was initiated on the P&H models 2300 and 4100 electric shovels during August 1996. Results of these technologies have shown the potential for improving electric min- ing shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition-based planning of component replacement. Maintenance costs are minimized by focusing resources through condition-based prioritization.

Jan 1, 1997

By A. F. Peterson

There is no single mining problem at Benson that does not exist at some other mine. There are four, however, that require special attention primarily because they occur together and have an influence on each other. These are the nature of the mineral occurrence, the shape of the ore body, the operating schedule, and the climate. It is the purpose of this paper to describe mining practices in relation to these four factors. Iron ore was first noticed in the Star Lake area early in the nineteenth century. Prior to Jones and Laughlin leasing the facilities built by the Defence Plant Corporation, several companies tried to mine the ore body but gave it up as uneconomical. While there is a little high grade (40%) magnetite, most of the ore contains 20 to 25% iron and not enough was known prior to World War II to design a profitable operation. By 1943, and certainly in the years that followed, technological developments in ore dressing and mining not only put the magnetite into the category of a commercial ore, but made possible the concentration of the non-magnetic iron mineral, martite. This last development nearly doubled the ore reserve. Jones and Laughlin bought the DPC holdings in 1946 and has since expanded the plant to its present capacity of 4,400 gross tons of concentrates daily or 1,600,000 gross tons per year. Magnetite makes up 62% of this production at the present time, but it will be necessary before long to bring martite production up to about 45% of the total because of the ratio of the two ores in the reserves. To keep the plant supplied, 14,000 to 15,000 tons must be mined and crushed daily, with a ratio of concentration that varies from 2.8 to 3.4. The ore body is 12,000 feet long and varies in width from 600 to 1,500 feet. The waste rock is, for the most part, a granite gneiss, and the overburden, of which little is left, is a glacial drift sand. For the entire reserve, there is a half ton of rock for every ton of concentrate, but the stripping ratio is more than one to one at present because of the existence of more rock in the upper mining levels in relation to the ore. The dirt stripping or development work that cannot be handled by company facilities is contracted to an outside firm. The need for this diminishes every year and will soon disappear. The deposit looks like a "J" in plan, with the long leg running approximately north and south and the short leg to the west. The primary crushing plant, consisting of a 54" gyratory followed by two 18" gyratories and a 1,500 foot conveyor belt to the fine crushers, is located on the third level where the long and short leg of the mine meet. The widest part of the pit lies just the north of the crusher. The mine is operated on a lease that expires in 199l0 There are two fee owners, the Benson Iron Company, which owns slightly overhlf of the reserves, and the Newton Falls Paper Company, which owns the balance. There is no appreciable difference in the mining on the two fees, so the ore is removed in strict proportion to calculated reserves during each year. Basic mining equipment consists of eight 45 yard electric shovels, a fleet of twenty-five 22 ton end dump trucks, eleven churn drills for nine inch blast holes, and two small percussion drills for four to five inch holes, There are the normal auxiliary items, such as dozers, graders, wagon drills, and two drop-ball cranes. Power is purchased and, where practical, is used at 4100 volts. Pit drainage pumps can handle a maximum of 11,500 GPM from the several sumps, but water is a problem only during the spring or when a sudden thaw follows a heavy snowfall.

Jan 1, 1958

By D. Spindler

Pursuant to the Federal Surface Mining Act of 1977 and the Illinois Surface Mining Act of 1980, Illinois has adopted revegetation success standard regulations that include the Agricultural Land Productivity Formula. The Formula establishes yield goals and standards to measure the success of meeting yield goals for reclaimed prime farmlands. The formula compares the quality of the pre-mining soils in the permit area and the county, to the crop production achieved on the reclaimed permit area and the county crop yield in a given crop year. The regulations also specify acceptable crops, erosion control requirements and time frames for demonstrating success.

Jan 1, 1986

By George F. Swindle

This paper discusses a composite of two coal reserve studies, each of which made use of a computer-based modeling system to assist in an evaluation of multi-seam deposits. The model permitted simultaneous consideration of seam thickness, seam structure, overburden thickness, over-burden ratio, and quality parameters for sulphur content, ash content, BTU values and the EPA Compliance index. The model is designed for use by a non-programmer, geologist or mining engineer. It enables the user, from a computer terminal in his office, to specify constraints (for example maximum um sulphur and maximum- ash content, minimum seam thickness and minimum BTU rating), and produces a report showing the volume, quality and location of that part of the total in place deposit satisfying all the constraints.

Jan 1, 1983

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By Shiro Ishii

When construction sites are in a densely- populated area or near roads, railroad or river, restrictions upon the ways of handling and using explosives such as dynamite and large demolition equipment are being increasingly stringent, in consideration of environmental pollution such as noise, vibration, dust, flyrocks etc., and safety precaution. In view of this, the development of safe and pollution-free technology for demolishing rocks at mines and reinforced concrete structure at building sites is strongly required. To meet such requirements, the demolition by means of expantion of mineral substances has been considered long before. Recently with the demolition technique using non-explosive demolition agent developed by ONODA CEMENT CO., LTD., holes are drilled into substances to be demolished, such as rocks and concrete before-hand. Then, slurry of such agent mixed with an appropriate quantity of water is poured into the holes. It hardens and expands with the passage of time, and the expansive stress reaches more than 3m/m2 in 10 to 24 hours. This expansive stress causes the material to crack. In this article, descriptions of the non- explosive demolition agent, BRISTAR manufactured by ONODA CEMENT CO., LTD., TOKYO, JAPAN, are given briefly with regard to its physical and chemical properties and its method of use; and the way it is used at an actual construction site is reported.

Jan 1, 1982

By Laurindo De Salles Leal Filho

Microflotation tests with sodium oleate, in alkaline pH, were performed with apatite and some silicates (phlogopite, quartz, and chlorite) that commonly occur in Brazilian phosphate ores. Further flotation tests were carried out with selected ores containing the same silicates as important gangue minerals. The results showed that apatite recovery is highly affected by competition with silicate minerals, probably activated by calcium ions dissolved in flotation pulp. Inorganic chemical species (sodium tripolyphosphate, sodium carbonate/ bicarbonate, and carbon dioxide) that could act as water softeners were used as modifier agents. They proved to be capable of improving flotation recovery and selectivity.

Jan 1, 1999

By Pengfei Wang, Guorui Feng

"With the depletion of easily minable coal seams, less favorable reserves under adverse conditions have to be mined out to meet the market demand. Due to several historical reasons, a large amount of remnant coal was left unrecovered. One such case history occurs with the remnant rectangular stripe coal pillars using partial extraction method at Guandi Coal Mine, Shanxi Province, China. The challenge that the coal mine is facing is that there is an ultra-close coal seam right under it, with an only 0.8 to 1.5 m sandstone dirt band in between the two. The simulation study was carried out to investigate the simultaneous recovery of upper remnant coal pillars while mining the ultra-close lower panel using longwall top coal caving (LTCC). The remnant coal pillar was induced to cave in as top coal in LTCC system. Physical modelling shows that the coal pillars are the abutments of the stress arch structure formed within the overburden strata. The stability of overhanging roof strata highly depends on the stability of the remnant coal pillars. The gob development (roof strata cave-in) is intermittent with the cave-in of these coal pillars and the sandstone dirt band. FLAC3D numerical modelling shows that the multiple seam interaction has a significant influence on mining-induced stress environment for mining of lower panel. The pattern of the stress evolution on the coal pillars with the advance of the lower working face was found. This demonstrates that the stress relief of a remnant coal pillar enhances the caveability of the pillars and sandstone dirt band below them.INTRODUCTIONChina is one of the world’s coal-rich countries. Coal has played a significant role in the growth of China’s economy. Coal reserves have been mined commercially in China for over one hundred years. The demand for coal in China is still going to grow at a relatively high rate (BP Energy Outlook, 2019). Long-term large-scale and intensive coal mining activities have created tension between increased demand and limited resources (Bai et al., 2018). Easily minable coal seams such as sub-horizontal, tabular, and laterally extensive coal seams are being depleted, and therefore the remaining reserves are becoming less favorable. However, in many situations, the coal reserves under adverse conditions have to be mined out to meet the market demand for energy.Due to sedimentary environments and geological conditions, many coal seams are interspersed with sedimentary bands, or partings both within an individual seam and between seams. These bands and partings lead to appearance of ultra-close coal seams, as well as giving rise to considerable variation in their structural and mechanical properties (Ghabraie and Ren, 2016). Difficulties are encountered in the mining of such coal seams. If ultra-close coal seams are mined sequentially, that requires the design of a mining system for each individual coal seam; also, a large number of gateroads have to be excavated, which is not a high-efficiency option. If ultra-close coal seams are mined at a great mining height at once, for instance, using longwall top coal caving—a longwall mining method that is widely used in China for the mining of ultra-thick coal seams—then the location and characteristics of the band would have a significant influence on success of their extraction."

Jan 1, 2019

By Stanley V. Lachmansingh

Bauxite can be regarded as a mixture of hydrated aluminium oxides the predominant constituent - and oxides of iron and titanium, silica and silicates. Heterogeneous and non-crystaline, most bauxites vary in average composition from one deposit to another both in terns of impurities as well as the proportion of Gibbsita and the Monohydrates Diaspore and Boehmite. Iron levels (as Fe2O3) can vary from less than 1% to as high as 30% with the alumina content ranging from 40 to 6o%,. Gore than 90% of all bauxite mined in Guyana is used as feed for the - production of refractory grade calcined bauxite. There are -however, several speciality grades used in various industrial applications and these are characterised by the quality of the bauxite in particular ;,with regards to iron and silica levels which generally have to be low. The main speciality grades are designated Refractory, Abrasive and Chemical. Bauxitte is also used in the production of nigh alumina cements,, activated bauxite end in the manufacture of electrical insulators.

Jan 1, 1977

By F. J. Bruey

Refdist is a simple but valid approach to planning or analyzing a test-vs-control plant trial that uses accumulated plant performance data to calculate objective criteria for judging the trial outcome. Refdist calculations and results are explained and illustrated with data typical of the mining industry. Findings from a simulation study of Refdist statistical properties are reported. Suggestions for dealing with messy data situations are offered.

Jan 1, 1999

By A. Jahedsaravani, M. Massinaei, M. H. Marhaban, N. Mehrshad, M. I. Saripan

"It is well known that froth visual features reflect the operating conditions of the flotation process, so that being able to accurately obtain the froth properties is the most significant criteria to optimize and control this process. Froth segmentation is a useful procedure that can determine the bubble size distribution. Several algorithms have been proposed in this field, but marker-based watershed transform shows the best performance. In spite of this fact, the algorithm suffers from oversegmentation in cases when the flotation froth includes large bubbles along with small ones. In the paper, the marker-based watershed method is modified to prevent oversegmentation of large bubbles. The developed algorithm is validated using some froth images captured at different operating conditions, so the results indicate that the method can segment the mixture of big and small bubbles effectively.IntroductionFroth flotation is a widely used process for separating valuable from gangue minerals. Effective control of flotation circuits has a dramatic effect on overall performance of a mineral processing plant. In most flotation plants, process operators monitor the froth surface visually and make adjustments to process parameters based on their interpretation of the surface appearance and their idea of the appearance of an ideal froth. However, due to natural complexity of the flotation process, achieving optimal control is often not possible for human operators.In recent years, attempts have been made to control the flotation circuits using machine vision systems (Moolman et al., 1995; 1996a,b; Bartolacci et al., 2006; Kaartinen et al., 2006; Vanegas and Holtham, 2008; Aldrich et al., 2010). The froth bubble size distribution is the most significant control variable that reflects the operating conditions in a flotation machine. To date, a number of approaches have been proposed for bubble size measurement from froth images, including segmentation (Sadr-kazemi and Cilliers, 1997; Wang et al., 2003; Mehrshad and Massinaei, 2011), texture spectrum (Nguyen and Thornton, 1995), wavelet (Liu et al., 2005), an improved texture spectrum approach, a method based on binary images (Lin et al., 2008) and, finally, using interfacial morphological information (Yang et al., 2009)."

Jan 1, 2015

By W. M. Haffner, S. L. Borek, H. M. Edenborn, R. W. Hammack, D. H. Dvorak

The conceptual designs of three new applications for the biogenic &S treatment of metal- containing waters are presented. These include: 1. the treatment of a circumneutral-pH ground water containing Zn and Cd using limestone as an alkalinity source, 2. a two-step treatment process where toxic heavy metals in contaminated ground water are recovered separately from nontoxic metals to lessen disposal costs, and 3. a copper recovery process that may be a low-cost alternative to solvent extraction/electrowinning or cementation for dilute copper leach liquors. Preliminary results of initial field testing are discussed

Jan 1, 1995