Search Documents

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By Albert L. St. Peter

The "Old Reliable" four million pound blast in March of 1972 marked the opening, as far as is known, of serious efforts to commercialize the In Situ concept. That was a coyote shot, and it was followed by three blasts at McAlester Fuel's "Zonia" operation which were surface hole shots. As the only individual who had a principal part in all four shots, it seems to be appropriate to present experiences in the developments and evolutions of the in Situ method of ore extraction. Some of the problems will be described, along with proposals for management of such projects in the future.

Jan 1, 1976

By R. Musu, J. A. E. Bell

P.T. Inco has constructed a smelter to produce 45 000 tonnes (49 500 tons) of nickel per year as a nickel matte from the lateritic ores of Sulawesi, Indonesia. The facilities include mines, five screening stations, two dryers, three novel reduction kilns, three electric furnaces, three top blown rotary converters, and associated infrastructure of port, towns and a hydroelectric generating station. The screening stations and converters are unique in the industry. The problems encountered in the construction and operation of this complex facility in remote Indonesia are described.

Jan 1, 1979

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.

By S. Behl, S. Mathur

The viability of physico-chemical purification methods such as selective, flocculation for the separation of two components having similar chemical compositions and the same crystal structure but different surface properties is demonstrated. A loss of selectivity was observed in a dolomite-dolomite mixture when polyethylene oxide (PEO) (five million molecular weight) was used us the flocculant. Heteroflocculation was minimized using a low molecular weight PEO (MW =105) as a site blocking agent (SBA). Near complete separation was achieved at pH 10.5 at the 100% recovery level

Jan 1, 1996

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By Zhengbin Cheng, Wenguang Lu, Baoqi Sun, Jiaying Tang

This paper studied the flotation separation of feldspar, zircon and kyanite from quartz with a mixture of cationic and anionic collectors. Tests show that collector mixture has specially good effect, using it, the separation of these three silicate minerals from quartz can be successfully achieved at the natural pH value of tap water in the absence of any acid, fluoride and other inorganic reagents. The properties and characteristics of collector mixture were analysed. By means of IR-spectra, ESCA and AES, the action mechanism between collector mixture and minerals was throughoutly studied.

Jan 1, 1995

By Ross W. Smith, Xiapeng Zheng, Merrill P. Allen

The results of flotation of a primary desliming hydrosizer overflow material containing 14.6 wt.% P20, and 3.6 wt.% MgO are presented. The phosphate minerals were collophane and francolite and all minerals appeared to be liberated. The material had not been previously treated with flotation reagents. In the experimentation, various collectors were evaluated for effectiveness. The relative effectiveness of flotation in different flotation devices was determined. Finally a two-stage flotation scheme is proposed using column flotation of dolomite in the first stage and Denver cell flotation in the second.

Jan 1, 2002

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

Single-unit separations in mineral processing are typically not able to meet the strict purity requirements for consumer markets. As a result, multistage separation circuits are often employed. Because these circuits represent a large and inflexible capital investment, process engineers are careful to ensure that the circuit is optimally designed to meet the desired objectives. The set of interdependent decisions that constitute the circuit design may involve the selection of different unit operations, different equipment specifications, different operational parameters, and different unit interconnections. To assist circuit designers in assessing these options, researchers have attempted to establish standard design methodologies that involve various techniques and tools.

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

Tellurium (Te) is an important scattered metal. Known as the vitamin of modern industry, national defense and cutting-edge technology, it is the supporting material for new high-technology materials. Currently, its separation and extraction from Te-bearing materials face problems such as long flowsheets and high reagent consumption, giving rise to an urgent need to develop new methods for its recovery.

By M. Misra

The interaction of xanthate with SO2 in the flotation of sphalerite and chalcopy.ite is discussed. 'The SO depression of sphaledte is due to the decomposition reaction of xanthate by SO2 The decomposition reaction is dependent on the cole ratios of xanthate/SO2, oxygen concentration and pH. Xanthate adsorbs at a faster rate by chalcopyrite than sphalerite. The faster rate of xanthate adsorption by chalcopyrite and the specific action of S02 on the surface of chalcopy.ite facilitate the selective separation of chalcopyrite from sphaledte.

Jan 1, 1989

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By R. G. Darmody

Longwall coal mining in southern Illinois occurs beneath some of the best agricultural land in the U.S. This region is characterized by highly productive, nearly level, and somewhat poorly drained soils. Subsidence from longwall mining causes changes in surface topography which alters surface and subsurface hydrology. These changes can adversely affect agricultural land by creating wet or ponded areas that can be deleterious to crop production. While most subsided areas show little impact from subsidence, some areas experience total crop failure. Coal companies are required by law to mitigate subsidence damage to cropland. The objective of this study was to test the effectiveness of mitigation in restoring grain yields to their pre-mined levels. The research was conducted on sites selected to represent conventional mitigation techniques on the predominate soils in the area. Corn (Zea mays L.) and soybean [Glycine max.(L.) Merr] yields in 1988, 1989, 1990, and 1991 from mitigated areas were compared to yields from nearby undisturbed areas. There was no significant (a=0.05) difference in soybean yields averaged over the four years. Average corn yields, however, were significantly lower than reference areas. The impact of subsidence and mitigation is variable and site specific. Results were also related to weather. In wet years, yields in mitigated areas tended to be depressed. This research demonstrated that mitigation of subsidence damage can be successful.

Jan 1, 1986

By P. W. Conrad, C. Todd, N. A. Degerstrom, N. West, R. Kramer

"Surface subsidence caused by underground room-and-pillar mining operations and by solution mining operations have been studied separately but never in combination. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Using Salt_Subsid, a subsidence software package from the Solution Mining Research Institute, and ArcGIS, Esri's mapping platform, researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. Project backgroundFMC Minerals has increased the production of trona from its Westvaco Mine near Green River, WY, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 488 m (1,600 ft). Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed.The location from which the trona is removed and the size of the cavern created by the solution mining operations are important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found between surface subsidence measurements and the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find relationships between the measured subsidence and the solution mining activities. The project attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The project attempted to model the relationship between the measured surface subsidence and solution mining production using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI, Clarks Summit, PA) to estimate the location, size and shape of the solution mining cavern. This study would determine the program’s usefulness for locating and developing the cavern created by secondary solution mining activities. The subsidence and production data sets used in this study were collected over a seven-year period from 2008 through 2014."

Jan 4, 2018

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"The U.S. National Institute for Occupational Safety and Health completed a 15-month study at an underground limestone mine crusher booth that evaluated three research parameters: (1) the effectiveness of a filtration and pressurization system for improving the air quality inside the operator booth, (2) the relative effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) the performance of three different cab pressure monitoring devices. The protection factor was quantified monthly using particle counters in the respirable dust range of 0.3 to 1 µm particle size, and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static (closed-door) conditions, the filtration unit offered a gravimetric calculated protection factor between 10 and 31, depending on the filter type and loading condition. The monthly particle counting analysis shows that the ? > 95 filter offers a protection factor nearly five times that of the ? > 99 filter, where n = 15 samples. The booth pressure monitors were tested and proved to be a valid indicator of system performance over time. IntroductionDesigned and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from noise and physical hazards, such as flying rock and debris, as well as a more comfortable environment in regards to temperature and humidity (Organiscak et al., 2016). While it is easy to quantify the operation of a cab’s air-conditioning unit by measuring the temperature, or observe whether the cab offers protection from flying debris, it is somewhat more difficult to quantify its performance in reducing respirable dust hazards.The U.S. National Institute for Occupational Safety and Health (NIOSH) has been conducting applied research to improve the air quality inside the enclosed cabs of mobile equipment, resulting in the mathematical modeling of enclosed cab filtration systems (Organiscak and Cecala, 2008). The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms (Noll, Cecala and Hummer, 2015). While stationary enclosures are similar to mobile cabs, the work area can be significantly larger. Workers in booths and control rooms also tend to stay within the enclosure for a greater percentage of the day as opposed to workers on mobile equipment who enter and exit frequently."

Jan 1, 2018

By Saied S. Navid, Michael A. Piepenburg, Richard F. Escandon, Robert C. Lindsay

INTRODUCTION Phase I of the Los Angeles Metro Rail Project, known as MOS-1 (Minimum Operable Segment-1), is the first phase of the 27 km± (17 mi) subway starter line. MOS-1 is currently under construction and involves approximately 6.4 km (4.4 mi) of subway, five stations, yards and shops routed through the downtown area of Los Angeles. The project will form the initial heavy rail backbone of a more extensive light and heavy rail transit system planned for the greater Los Angeles area in the future. Construction Contract A-171 is one of 4 tunnel contracts within MOS-1 and involves construction of twin tunnels running from the downtown metropolitan area west to MacArthur Park. The heavily populated and developed downtown area, potentially gassy ground conditions, and the possibility of undocumented abandoned oil wells in seismically active southern California made the design and construction of Contract A-171 a uniquely interesting project. This paper summarizes the construction history to date (December, 1988) including design geotechnical considerations, tunnel support design, as-built geologic conditions, shield tunneling performance through soft ground, and ground response. The findings presented herein may aid in the design and construction

Jan 1, 1989

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By J. Kemeny, J. Lyons-Baral

"Point cloud technology is now an indispensable tool in geological and geotechnical data collection, interpretation and analysis. Open pit and underground mines of all sizes are regularly collecting point cloud data as Laser Scanning (LiDAR) and Photogrammetry surveying devices have finally become affordable and the workflows fast and efficient. Past challenges of large data processing and manipulation are gone with recent technological advancements in computer hardware and software. These innovations reduce file sizes, ease rendering requirements and allow for the implementation of real-time 3D viewers and surface meshing tools. With its ability to remotely (safely), rapidly and accurately extract large quantities of georeferenced and 3D-oriented data, point cloud technology provides numerous applications to the geomechanical field. The list of uses is continuously growing, so this paper specifically focuses on digital outcrop modeling and digital terrain engineering. INTRODUCTION Point Clouds The high-resolution and increasing availability of point cloud technology is rapidly improving open pit and underground mines’ investigation, interpretation and characterization of site geology and rock mass properties (Kemeny et al., 2015; Lyons-Baral, 2012). LiDAR and photogrammetry are common remote sensing methods employed to measure the coordinates of surfaces in three dimensions (3D), providing the X, Y and Z locations, and typically the reflective intensity and/or the visible three-band color of each point (Figure 1). LiDAR uses either a time-of-flight or phase-shift measurement of a laser beam reflected off targeted surfaces and received back into the device. Photogrammetry generates point clouds by merging multiple overlapping photographs and uses stereographic plotting to define the locations of object points in 3-D space. These methods can be deployed from airplanes, unpiloted aerial systems (UAS or drones), tripods, land vehicles, and even in a mobile backpack shown in Figure 2. RADAR, Total Station-Prism and other remote sensing systems also offer very precise “point clouds”, but this paper does not address these due to their higher cost and lower versatility and mobility. Technology In the past few years point cloud acquisition device prices have dropped significantly, devices have become lighter, smaller and easier to operate, and processing and utilizing the data has also become faster and easier. Device size improvements include mobile backpacks (Figure 2) and handheld mobile LiDAR (CISRO, 2014), allowing mobile scanning in tight spaces both above and below ground or inside and outside of man-made structures. Airborne data acquisition options have expanded dramatically with the spread of UAS technology as seen in Figure 3 (Hexagon Geosystems, 2015). Once UAS usage regulations are sorted out, these versatile machines will be everywhere, offering high resolution coordinate scans, imagery and other remote sensing. While backpacks and handhelds allow access to tight quarters, UAS permit rapid data capture from narrow to broad areas with multiple perspectives reducing data “shadows.”"

Jan 1, 2016

By James P. Sabogal

A control and monitoring system is being developed by Betz Laboratories for the heap leach process in gold recovery. Called Betz 14000GL, the system is designed to improve gold leaching and provide savings in chemical consumption by controlling and monitoring key parameters in the heap leach gold recovery circuit. The system uses information from on-line sensors to control antiscalant chemical addition, pH and cyanide levels. The proprietary graphics and report features of the computer system allows the user to monitor and critically evaluate the performance of the process.

Jan 1, 1998