Search Documents

By R. D. Hansen

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures do exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers end some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1985

By J. W. Leonard

Since the interpolation of exploratory data 1 can be no better than sampling procedures, a series of field experiments were conducted in an effort to determine whether hand-cut channel or core washability determinations best represent continuous miner produced run of mine coal. By obtaining a core drilled to within a few feet of channels taken from an underground face and then overmining both locations; core, channels and run-of-mine coal allocations were obtained from a common sample and all allocations were subjected to identical washability determinations. In order to compare results, basic rules2,3 previously anticipated and later published by the writer were employed. The first rule states that "For any full seam washability determination, the sulfur versus ash function for increasing cumulative specific gravity float coal fractions is linear". The second rule states that "For any full seam washability determination, the recovery versus ash function for increasing cumulative specific gravity float coal fractions is logarithmic".

Jan 1, 1988

By G. Robson

"From monitoring gas levels and air quality in coal mines to protection from collisions for large vehicles at mine sites, SICK offers a wide range of sensors and systems to improve safety and to monitor potentially dangerous situations. SICK offers solutions for the analysis and monitoring of underground coal mining atmospheres. These systems supply the coal mine operator valuable safety and ventilation information, as well as data which identify and monitors atmospheres of those production areas within the mine which may or may not be worked, such as Goafs and sealed areas. Underground coal mines contain dangerous gases, which must be monitored and controlled in order to allow productive mining operations to take place and to minimize the risk of explosion. Underground mines are a potentially dangerous place for mine workers. These are the main reasons for using Tube bundle systems SICK has had great success in selling these systems into the Australian and New Zealand Markets and this is helped by the strong drive for mine safety from both the Mine Owners and the Regulatory bodies charged with the responsibility of ensuring Mine Regulations are met. The Australian mining industry uses Tube Bundle Systems at almost all underground sites, even after mining has ceases and the mine is placed in care and maintenance. Sick has been working in international markets for some time now but has had limited success in selling Tube bundle Systems to these markets. However in recent times there has been raised interest in Tube Bundle from China, India and Turkey as these countries strive to improve mine productivity and lessen the risk of explosion or Spontaneous Combustion. Our lack of penetration into International Coal markets has been very much based on the perceived cost of the system, not the benefits to safety and productivity. Unless a mine has had an event such as spon com or a Methane explosion they rarely consider the very low level measurement capability (20 PPM CO & 100 PPM CH4) or the long term trending benefits of the Tube Bundle system. It is only after a catastrophic event the System is considered. Real Time or electrochemical Sensors are commonly used to monitor the Mine Atmosphere, the real problems of methane build up or potential Spon Com in Goafs and sealed areas cannot be monitored using Real Time Sensors as the electrochemical cell deteriorates after approx. 12 months and in sealed areas these cells cannot be maintained or replaced. Whilst the Technique of Tube Bundle Systems is quite old SICK have spent many years redesigning the Tube Bundle System into a cost effective and real value for money product. The system uses state of the art sampling and highly accurate Infra-Red wide Spectrum Analysers."

Jan 1, 2016

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By Nikhil Dhawan, Shrey Agrawal, SHAILA MIR

The current study investigates the effect of microwave processing on low-grade banded iron ore using charcoal, coking coal, and non-coking coal. Charcoal showed better microwave heating response at low temperatures, and the coals exhibit better heating response at higher temperatures. Low carbon dosage ~ 12% is sufficient to generate concentrate with 61.8% iron grade and ~6% for 94.8% iron recovery comprising of magnetite phase suitable for iron-making applications. The process separation efficiency of ~ 95% is achieved at 6% carbon dosage and decreases with an increase in carbon due to formation of the fayalite phase. The metallization degree showed a strong dependency on reductant dosage and achieved amaximumvalue of 22.7%at 18%charcoal. The comparison of ore with pure iron oxide and the synthetic mixture of iron oxide indicated that the underlying bonding due to banded structure enhances the Joule heating during microwave irradiation and thereby aids in attaining higher temperature and better separation.

Sep 21, 2020

By Christophe Bragard, Rebecca Reeve

The Regional Connector Transit Corridor (RCTC) Project is a 1.9-mile-long metro light-rail extension project that traverses the historical core of downtown Los Angeles, California. This project aims to improve mobility throughout downtown LA with fewer transfers for riders. It is designed to connect two existing rail lines for a more seamless travel. The project consists of twin bore tunnels, three new stations, and is scheduled to be completed in 2022. The design-build contract was awarded to the Regional Connector Constructors (RCC) in 2014, a joint venture of Skanska and Traylor Bros, Inc. with Hatch Mott MacDonald as the designer. One of the challenging aspects of the project was the construction of a crossover cavern in a narrow public right-of-way surrounded by historical structures. RCC used Sequential Excavation Method (SEM) to construct the crossover cavern measuring 287 ft long by 58 ft wide by 36 ft tall. The initial lining of the cavern featured a 12 in. fiber reinforced shotcrete lining. The initial lining was separated from the final lining by a hydrocarbon resistant membrane, as specified by the standard requirements of Metro. The cavern features a cast-in-place final lining with a thickness of 5 ft 9 inches in the invert and 18 inches in the crown and walls. The structure also features a nonload bearing plenum slab and interior walls for ventilation.

Jun 13, 2021

By Ronney Rodrigues Silva, Renata Mendonca, Gabi Knesel, Cathrine Monyake

Locus Mining is working side-by-side with a prestigious iron ore company to evaluate the addition of Locus ESG-friendly green flotation reagents with the primary goal of improving recovery and grade. In this paper, we will focus on the cationic reverse flotation application. The most “established industry” reagents for cationic reverse flotation are amine as the collector, starch as the depressant, and in some cases frothers are also used (among them MIBC, pine oil, others). Here, we evaluate the synergies of different classes of eco-friendly biosurfactants and industry-standard reagents during the cationic reverse flotation method. Exploratory research was done first with an analog sample under different pHs, eight different biosurfactants with starch and no-starch, and a customized DOE was used to perform 145 microflotation tests. The results show Separation Efficiency from 20% (baseline) to 50% (biosurfactant), and Selectivity from 3.27 (baseline) to 5.67 (biosurfactant). Optimized result conditions were then applied to the iron ore samples received from our client to perform flotation tests on a Denver Lab cell. Similar results were obtained by improving Separation Efficiency and Selectivity, which corroborate with the previous work.

Feb 1, 2025

By GRANT COLLIGAN, BROCK O’KELLEY, Corby Anderson

With the world’s ever-expanding push to expand technological capabilities, the need for specialized materials including rare earth elements has exploded. One source found in the USA is bastnaesite, a rare earth bearing fluorocarbonate mineral, currently mined at the Mountain Pass Mine in California. To increase production, it is essential to optimize existing processes and create new ones to better utilize current resources. Therefore, a US Department of Energy Critical Materials Institute sponsored research program was carried out at the Kroll Institute for Extractive Metallurgy to expand the fundamental understanding of the industrial bastnaesite concentrate leaching system. With the help of prior knowledge, thermodynamic calculations and design of experimentation based lab testing, a novel single-stage hydrochloric leach system was created to optimize the rare earth extraction from bastnaesite. Historically, the existing industrial process has utilized a two-stage leach system involving a high-temperature hydrochloric acid leach with liquid solid separations followed by a caustic crack stage of the leach residues. A series of single-stage leach experiments were run by reacting locked cycle flotation concentrates with hydrochloric acid to test common leaching parameters. The results of these patent pending single-stage tests have shown rare earth recoveries significantly higher than reported recoveries of historic two-stage caustic crack processes, all while decreasing the equipment required and the type and amount of reagents needed.

Jan 31, 2022

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1990

By Zoë Dugdale, Gerald Poplin, Tim Bauerle

"Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetitive duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising.Mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a cookie-cutter approach. However, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; long commute times due to mine site remoteness; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present all together. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining.While the burden of fatigue on the mining population has not yet been evaluated thoroughly, methods and measures of fatigue management remain a popular point of discussion. Many commercial suppliers and consultancy groups have begun to develop technologically based fatigue monitoring systems (McMillian, 2013). Some technologies can monitor vehicle operators for indicators of wakefulness, such as percent eyelid"

Jan 3, 2018

By T. E. Bernard

"Refuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet the U.S. Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and management of heat from the occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements and carbon dioxide generation that are representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current U.S. coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in.) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in a refuge alternative. The highest likely metabolic heat generation ranged from 113 to 134 W, depending on occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 L (0.81 cu ft) of oxygen per hour per person and 20 L (0.71 cu ft) of carbon dioxide per hour per person, which means the margin of safety is 50 percent or more compared with the MSHA requirements. The information on metabolic heat generation can be used to assess refuge alternative thermal environments by testing or simulation. The required oxygen supply and carbon dioxide removal can be used to assess refuge alternative requirements. IntroductionRefuge alternatives provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their refuge alternatives meet U.S. Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen (O2), removal of carbon dioxide (CO2) and management of heat resulting from the refuge alternatives’ occupants and mechanical/ chemical systems (MSHA, 2008)."

Jan 8, 2018

By E. Jong, E. Watkins

"The application of passive tracer gas sources in underground mines is particularly useful for long-term tracer studies as well as for studies conducted in permissible areas of underground coal mines. The use of passive perfluoromethylcyclohexane (PMCH) sources has been previously demonstrated in underground mines, but this new work details the testing of multiple, distinct tracer compounds compatible with passive sources. A description of their potential application in mine ventilation systems is also provided. Three tracer compounds are detailed: (1) PMCH, (2) perfluoroethylcyclohexane (PECH) and perfluoromethylcyclopentane (PMCP). The release rates of these tracers were examined over a 180-day period at multiple temperatures. The advantages and disadvantages of these sources are presented, along with potential applications in characterizing ventilation circuits, flow through gob and leakage. IntroductionThe use of tracer gases for ventilation applications is an established practice, with various past research projects conducted using sulfur hexafluoride (SF6). Tracer gas techniques have been applied to assess flow rates, dilutions rates and auxiliary ventilation system efficiencies with quick, reliable and accurate results (Suglo and Frimpong, 2002). Perfluorocarbon tracer (PFT) compounds are a new introduction to ventilation and air modeling applications in terms of ventilation flow characterization (Watson et al., 2007).PFTs are liquids that are characterized by low background presence in air, low reactivity, high detectability and low toxicity. A design was proposed, called a permeation plug release vessel (PPRV), to convert PFTs from a liquid to a gas and then release the gaseous tracer in a controlled manner. The initial concept was originally introduced by Brookhaven National Laboratory and refined later to become the PPRV. The PPRV functions by allowing the volatile PFT liquid to become a vapor in a controlled manner. The vapor diffuses through a permeable silicone stopper at a predictable rate proportional to temperature (Zhang and Cloud, 2006)."

Jan 2, 2018

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

The main purpose of mine ventilation design is to provide sufficient quantity and quality of air to the workers and to dilute methane and other contaminants. It is generally perceived that the additional air along the longwall face will improve methane dilution on the face and in the tailgate. However, computational fluid dynamics (CFD) modeling efforts at the Colorado School of Mines (CSM) under a National Institute for Occupational Safety and Health (NIOSH) funded research project have found that higher flow velocities along the longwall face are shown to increase the pressure differential between the gob and longwall face allowing more methane to be entrained in the active face and tailgate (TG) area, thereby negating the dilution effect. The increased face ventilation causes an increase in pressure along the headgate side which allows more oxygen to ingress into the gob area, thereby increasing the amount of oxygen available to form explosive methane air mixtures in the gob and to support spontaneous combustion of the coal. Two things are happening at two different locations along the longwall face, increase in pressure as the flow enters the active area cause an increase in pressure which forces more oxygen into the gob, but as the flow is developed along the longwall face, the higher velocities causes greater pressure drop allowing methane to enter the active face further downstream from the headgate (HG) towards the tailgate side. In this paper, a parametric study will be presented to discuss the effect that varying the face air quantity has on methane concentrations in the tailgate and formation of explosive gas zones (EGZs) in the gob. Counter to conventional wisdom, it appears that increased longwall face air quantities may increase the explosion hazard as they result in increased EGZ volumes in the gob, along with increased methane quantities in the tailgate return.

Jan 1, 2015

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc., and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the 'New Missouri Lead Belt' (See Figure 1). Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated about 1,100 feet below the surface at an elevation 270 feet above sea level, the flat lying sinuous ore bodies are up to 250 feet wide, 85 feet high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite, Access to the mine is through two 18'Ø concrete lined vertical shafts - one for servicing and the other for hoisting ore (See Figure 2). The mine is being worked by a modified room and pillar method using both rubber tired equipment and a sub-level rail haulage. Ore is broken from first pass headings, back and bench faces and transported by load-haul-dump units to ore passes located on 900 foot centers. The ore is pulled from chutes on the sublevel 90 feet below into 15 ton bottom dump cars and delivered in 10 car lots by a 15 ton diesel locomotive to a 42" gyratory crusher (See Figure 3). A recent innovation has been the introduction of two 50 ton trucks with plans to haul up to 60% of the ore on the mining level to an ore pass feeding directly to the primary crusher (See Figure 4). Ventilation raises up to 16'Ø, which were originally planned for 900 foot centers, are now driven on 450 foot centers.

Jan 1, 1973

By Roger K. McLimans

Sphalerite in the ores is multi-banded. Based on color and textures, bands in samples separated by a few kilometers may be correlated. Darkness of color is directly related to iron content. Isotopic and fluid inclusion data indicate that temperatures of ore deposition were 225°C-50°C. The agreement between these two sets of data suggests that chemical and isotopic equilibrium were established. The salt content and hydrogen and oxygen isotopic compositions are similar to present-day values of oil field brines suggesting a similar mode of origin. Ore transport and deposition are not adequately explained by either chloride or bisulfide complexing. Necessarily, other mechanisms were involved.

Jan 1, 1979

By Robert M. Dreyer

The first time that a geologist is confronted with the necessity of evaluating a lateritic ore deposit, he may feel that nothing could be easier. Why should there be any problems in making an economic evaluation of a relatively flat-lying, surficial ore body? After several hundred thousand dollars worth of frustrating work often culminating in a series of non-reproducible data - the evaluator may be a sadder and wiser man. This paper will try to illustrate why the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist - and, more especially, how this problem can be solved. Volumes have been published on descriptive and genetic studies of lateritic ores. Obviously, there is time today only for the briefest description of such an ore body. The laterite is a soil formed under tropical conditions and resulting in the concentration, within the soil zone, of certain tri-valent metals.- especially, aluminum and nickel. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of, partially altered bed rock or saprolite. It is important to remember that, whereas bauxite generally is confined to the laterite zone, nickel deposits occur in both the laterite and

Jan 1, 1977

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 m (8 ft) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting. Saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can prevent solution flow through large portions of the stockpile. This implies that care must be taken to ensure that ripping is carried out to a depth of at least 2.4 m (8 ft) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2002

By Steven Hoerger

Mixed integer linear programming (MILP) production scheduling models can be used to evaluate if tonnage improvement projects will deliver value over all time periods and whether new bottlenecks will be created. These MILP models can evaluate the interconnected effects of mine and process capacities, mining locations, cutoff grades, stockpiles, and orebody grade/tonnage distributions. A case study compares potential value creation from a mine capacity increase, a mill capacity increase, or a simultaneous increase in all capacities. For perspective, project valuations for capacity increases are compared against valuations for cost reduction projects, mine planning improvements such as phase design, dynamic cutoff grades and stockpiling, and the impact of geostatistics improvements in the areas of block model accuracy and ore control selectivity.

Feb 1, 2024

By Kumara S. Rachamalla

Long-term stability, appropriate taxation and incentive policies are essential to attract and stimulate investment in the mineral sector. An outline of Ontario's $4.6 billion industry and associated tax incentives is presented. Producers are offered incentives under The Mining Tax Act, federal and provincial income tax acts for exploration and development by reducing Me after tax cost to 13-25¢ for each dollar spent. The Mining Tax Act provides generous processing incentives which have positive effects in enhancing investment and economic advantages of building processing facilities. Non-mining companies and entrepreneurial individuals can receive 25% of eligible exploration expenditures in grants/tax credits under the Ontario Mineral Exploration Program.

Jan 1, 1982